Display RENAULT CLIO 2003 X65 / 2.G User Guide

QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page16
2.16
QUICKSHIFT 5 GEARBOX(continued)
Automatic mode
Automatic mode is selected by
default every time the ignition is
switched on.
You can change it at any time when
driving by pressing the mode
change button. The letterAappears
on the display.
The vehicle is controlled using the
accelerator and the brake. Gears will
change automatically at the correct
moment to a speed suitable for the
engine because the automatic
function takes into consideration
the weight of the car, the road
surface and the chosen driving
style.Note:
Automatic mode takes account of:
- the position and speed of
depression of the accelerator
pedal to assess driving style and
select the optimum gear,
- action on the brake pedal to alert
the engine brake by anticipating
the down-change
You can stop the vehicle at red
lights, with the gear engaged, by
pressing the brake pedal; there is no
need to change to neutral.
The vehicle will move off again:
- slowly, if you release just the brake
without accelerating (e.g. when in
a traffic jam)
- quickly, if you release the brake
and accelerate.
The level of oil in the
automatic gearbox system
reservoir is variable
depending on use. Adding
oil isstrictly forbidden(except by
qualified Renault network
personnel).

QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page17
2.17
QUICKSHIFT 5 GEARBOX(continued)
Accelerating and overtaking
You have two options:
1) slowly depress the accelerator
pedal to speed up gradually.
2) depress the accelerator pedal as
far as it will go (or: take your foot
off the pedal and depress the
pedal again until you reach the
point of resistance.
Parking
It is possible to park in gear (for
example, on a slope). To do this:
- with the ignition on, select a gear
with your foot on the brake.
- check that a gear other thanNis
displayed on the instrument
panel, then remove the ignition
key.
To disengage the gear, repeat this
operation by switching on the
ignition without starting the engine
and shift the selector lever to
neutralwith your foot on the brake.
Check thatNis displayed on the
instrument panel.

QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page18
2.18
QUICKSHIFT 5 GEARBOX(continued)
Horn
•If you keep the vehicle on a slope
for too long without applying the
brakes or handbrake, there is a
risk that the clutch will overheat.
In this event, an intermittent beep
will remind you that you should
put your foot on the brake or
apply the handbrake.
• Never leave the vehicle with the
engine running when in gear.
For safety reasons you will hear
an intermittent beep when you
open the door if you have not
shifted into neutral or you have
not switched off the ignition or
pressed the brake pedal.• Your vehicle will not start:
you can start the engine when the
vehicle is moving if the battery is
not discharged (display lit up).
Proceed as before:
- switch on the ignition
- select neutral
- push or tow the car or run it
down a slope until you reach the
speed at which the warning
buzzer is activated. This will
indicate that moving the
selector lever forwards will
engage the gear most suited to
starting the engine.
Note:never attempt this in reverse.
Operating faults
When driving,ifthis
warning light comes on, it
indicates a fault in the
system.
In most cases, you may still drive
the vehicle, although it will not
function perfectly. However, you
should consult a Renault Dealer as
soon as possible.
Towing a vehicle with a
sequential gearbox
If the gearbox is stuck in a gear:
- switch on the ignition
- select neutral with yourfoot on
the brake
- check that the gearbox is in neutral
(by pushing the vehicle, for
example).
If you cannot find neutral you must
tow the vehicle with the front
wheels raised.
Towing should always take place
with the ignition switched off.

1
26
5
3
4
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page21
2.21
CRUISE CONTROL - SPEED LIMITER: limiter function
The speed limiter function allows
youtodecideonamaximum
driving speed.
This may be useful, for example, in
town driving or in areas with speed
restriction (roadworks), etc.
The system operates above a driving
speed of approximately 20 mph
(30 km/h).Controls
1Main On/Off switch
2Limited speed storage switch and
adjustment of limited speed
(increasing).
3Return to stored limited speed.
4Switching the function off (with
stored limited speed)
5Limited speed storage switch and
adjustment of limited speed
(decreasing).
Indicator light
This orange indicator light lights up
on the instrument panel to indicate
that the limiter function is in
operation.
Stored speed information appears
on instrument panel display6
permanently or for approximately
30 seconds, depending on vehicle
type.

1
2
5
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page22
2.22
CRUISE CONTROL - SPEED LIMITER: limiter function(continued)
Switching on
Press the side switch1
The indicator light lights up in the
instrument panel and the on-board
computer enters speed limiter
mode.
Limiting the speed
At a stable speed (approximately
20 mph or 30 km/h) and in the
correct gear (for vehicles with
manual gearboxes), press switch2:
the speed is stored.
Driving
When a limited speed is stored,
press on the accelerator pedal until
you reach the limited speed.
From this point, no effort on the
accelerator pedal will allow you to
exceed the programmed speed
except in an emergency (see
information on exceeding the
limited speed).
Changing the limited speed
The limited speed may be changed
by acting (pressing frequently or
continuously) on:
-button2to increase speed,
-button5to reduce speed.
If the car has the temporary display
function, the limited speed is
displayed for approximately 30
seconds.

1
3
4
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page23
2.23
CRUISE CONTROL - SPEED LIMITER: limiter function(continued)
Exceeding the limited speed
In the event of an emergency
It is possible to exceed the limited
speed at any moment. To do this:
depress the accelerator pedalfirmly
and fully(beyond the point of
resistance).
The speed flashes on the instrument
panel (on-board computer) to
inform you that the cruise control
speed is being exceeded.
When the emergency has passed,
release the accelerator pedal: the
speed limiter function will return as
soon as you reach a speed lower
than the limited speed before the
emergency.
Impossible to operate at the limited
speed
If the limited speed cannot be
maintained by the system (for
example in the event of a steep
incline), the speed will flash on the
instrument panel (on-board
computer).
Switching the function off
The speed limiter function is
interrupted when you press:
- button4,inthiscasethelimited
speed remains stored
- button1,inthiscasethelimited
speed is no longer stored.
Confirmation that the function has
been switched off is given when the
indicator light on the instrument
panel goes out.
Return to limited speed
It is possible to return to a stored
speed by pressing button3.
If the car has the temporary display
function, the limited speed is
displayed for approximately 30
seconds.

1
26
5
3
4
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page24
2.24
CRUISE CONTROL - SPEED LIMITER: cruising function
When road conditions permit (fluid
or motorway traffic), the cruise
control allows you to take your foot
off the accelerator while your car
continues to cruise at the speed you
have selected. This is called the
“cruising speed”.
This cruising speed may be set at
any speed at speeds of 20 mph
(30 km/h) and above.Controls
1Main On/Off switch
2Cruising speed storage switch and
adjustment of limited speed
(increasing)
3Return to stored cruising speed
4Switching the function off (with
stored cruising speed)
5Cruising speed storage switch and
adjustment of limited speed
(decreasing)
Indicator light
This green indicator light lights up
on the instrument panel to indicate
that the cruising function is in
operation.
Stored speed information appears
on instrument panel display6
permanently or for approximately
30 seconds, depending on vehicle
type.

1
2
5
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page25
2.25
CRUISE CONTROL - SPEED LIMITER: cruising function(continued)
Switching on
Press side switch1
The indicator light lights up in the
instrument panel and the on-board
computer enters cruise control
mode.
Activating cruise control
At a stable speed (approximately
20mphor30km/h)andinthe
correct gear (for vehicles with
manual gearboxes), press switch2:
the speed is stored.
Driving
When a cruise control speed is
stored you can lift your foot off the
accelerator pedal.
Changing the cruise control
speed
The cruise control speed may be
changed by acting (pressing
repeatedly or continuously) on:
- button2to increase speed,
- button5to reduce speed.
If the car has the temporary display
function, the limited speed is
displayed for approximately
30 seconds.
Exceeding the cruise control
speed
In the event of an emergency
Thecruisingspeedmaybe
exceeded at any time by pressing
the accelerator pedal.
The speed flashes on the instrument
panel (on-board computer) to
inform you that the cruise control
speed is being exceeded.
When the emergency has passed,
release the accelerator pedal: your
vehicle will automatically return to
the speed previously selected and
the indicator light will go out.
Impossible to operate at the speed
selected
If the adjusted speed cannot be
maintained by the system (for
example in the event of a steep
incline), the speed will flash on the
instrument panel (on-board
computer).

1
3
4
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page26
2.26
CRUISE CONTROL - SPEED LIMITER: cruising function(continued)
Switching the function off
The function is switched off when
you:
- press the brake pedal,
- press the clutch pedal to shift to
neutral for vehicles with
automatic gearbox,
- press button4; in this case the
selected speed remains stored,
- press button1; in this case the
selected speed is no longer stored.
Confirmation that the function has
been switched off is given when the
indicator light on the instrument
panel goes out.
Return to cruising speed
A stored speed can be recalled by
pressing button3if you are driving
at a speed of approximately 20 mph
(30 km/h).
If the car has the temporary display
function, the limited speed is
displayed for approximately 30
seconds.This function is an
additional aid to driving.
However, the function does
not take the place of the
driver. Under no circumstances
should it replace observation of
speed limits nor vigilance and
responsibility on the part of the
driver.

12345
13 1211 10 9 8 7 6
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T3.WIN 30/10/2002 12:12-page14
3.14
AUTOMATIC AIR CONDITIONING
Controls
1- automatic mode button
2and12- air temperature
adjustment buttons
3-display
4and7- ventilation speed
adjustment buttons5- automatic windscreen
demister-de-icer button
6- air recirculation button
8to10- air distribution buttons
11- air conditioning button
13- unit off buttonAll buttons except2,4,7,and12
have associated indicator lights
which light up when the function
is being used and go out when the
function is not in use.