warning lights RENAULT CLIO 2003 X65 / 2.G Owner's Manual

QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06- page 7
2.07
ADVICE ON ANTIPOLLUTION AND HOW TO ECONOMISE ON FUEL WHEN DRIVING(continued)
Monitoring exhaust gas
The exhaust gas monitoring system
will detect any malfunctioning of
the vehicle's exhaust gas
depollution system.
If this system malfunctions, toxic
substances may be released into the
atmosphere or mechanical damage
may occur.
This warning light on the
instrument panel will
indicate if there are any
problems with the system:
This lights up when the ignition is
switched on and then goes out.
- If it lights up continuously,
consult your Renault Dealer as
soon as possible.
- If it flashes, reduce the engine
speed until the light stops
flashing. Consult your Renault
Dealer as soon as possible.
Driving
•Drive carefully for the first few
miles until the engine reaches its
normal operating temperature
rather than letting it warm up
while stationary.
• Speed is expensive.
• “Snappy” driving uses a lot of
fuel: drive with a “light right
foot”.• Brake as little as possible by
suitably anticipating an obstacle
or bend and then simply releasing
the accelerator pedal.
• Avoid sudden acceleration.
• Do not overrev the engine in
intermediate gears.
Use the highest gear possible
without labouring the engine.
(On versions with an automatic
gearbox, try to always use
positionD.)
• Try not to maintain the same
speed up a hill as you would on
the level; keep your foot in the
same position on the accelerator
pedal.
• Double declutching and
accelerating before switching off
the engine are superfluous
actions in modern cars.
• Bad weather, flooded roads
Do not drive on flooded
roads if the depth of
water is above the lower
edge of the wheel rims.

A
J
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page12
2.12
PROACTIVE AUTOMATIC GEARBOX(continued)
Economical driving
On the open road, always leave the
lever in positionD. Press the
accelerator pedal lightly to ensure
that the gears change automatically
at a low engine speed.
Never use positions D3, 2, 1 and the
snow position unless special
circumstances apply.
Parking the vehicle
When the vehicle is stationary,
place the lever in positionPwhile
keeping your foot on the brake
pedal: the automatic gearbox is in
neutral and the drive wheels are
mechanically locked by the
gearbox.
Apply the handbrake.
Operating faults
• If the lever becomes jammed in P,
even though you are depressing
the brake pedal, it can be released
manually.
To do this, unclip the coverJthen
simultaneously press the button
(located under the coverJ) and
the unlocking buttonAto move
the lever fromP.
Consult your RENAULT Dealer.• If warning lightIcomes
on when the vehicle is
being driven, it is
indicating that there is a failure.
Consult a RENAULT Dealer as
soon as possible.
• and :Ifthese
warning lights come on
simultaneously when the
vehicle is being driven, avoid
leaving the gear lever inD
position (orR) when stopping in
traffic: always return toN
position when stopped. Consult a
RENAULT Dealer as soon as
possible.
•If a vehicle with an automatic
gearbox breaks down,refertothe
information on towing in section 5.

1
4
3
5
2
6
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page13
2.13
QUICKSHIFT 5 GEARBOX
Selector lever
1Mode selection button: enables
you to move from manual mode to
automatic mode or from
automatic to manual mode at any
time with the engine running.
Note:The selector lever
automatically returns to the middle
position after use.Display
2automatic mode
3brake pedal depressed warning
light
4gear display
5not used
6gearbox fault warning light.
Thegearused(1,2..,5,N,R)is
indicated in the instrument panel
display. In automatic mode,(A)is
also displayed.
Driving
Switch on the ignition.
The display lights up on the
instrument panel.
As long as neutral is displayed (N),
start the engine but do not depress
the accelerator.
If a gear other than neutral(N)is
displayed this will flash;it will only
be possible to start the engine if you
press down the brake pedal (the
warning light3will come on if you
forget) when holding the key in
starting position.
The vehicle will then change to
neutral (N) automatically and the
engine will start.
Note: do not attempt to start the
engine by pushing the vehicle if the
battery is flat (the display remains
off when the ignition is switched
on).

QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page15
2.15
QUICKSHIFT 5 GEARBOX(continued)
Semi-automatic mode (manual)
When in automatic mode, moving
the selector lever up or down
through the gears or pushing the
automatic mode switch will switch
the system into semi-automatic
mode. If you push the switch, you
do not need to shift up or down
through the gears.
You can initiate gear changes using
the selector lever.
To move up through the gears
simply push the selector lever
forwards without necessarily
releasing the accelerator.
To move down through the gears
simply push the selector lever
backwards without necessarily
releasing the accelerator.The system will not tolerate a series
of up or down changes that cause
the engine to underrev or overrev.
Pushing forwards twice in
succession enables a shift up of two
gears at once (except in the case of
underrev). Pulling backwards twice
in succession enables a shift down
of two gears at once (except in the
case of overrev).
When decelerating with the foot off
the pedal, the gears will
automatically drop to the low speed
limit to avoid stalling. First gear
automatically passes below a
certain speed limit. You can stop the
vehicle at red lights or junctions etc.
by pressing the brake pedal; there is
no need to change to neutral (N).The vehicle will move off again:
- slowly, if you release the brake
without accelerating (e.g. when in
a traffic jam)
- quickly, if you release the brake
and accelerate.
Note:neutral is only accessible
when you are driving or stationary
withyour foot on the brake (if you
forget, the warning light3will
come on and theNsign will flash).
Push the gear lever to the right to
engage neutral.
Moving from one mode to another
can be performed with the engine
running, at any time and in all
ratios.

21
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page19
2.19
GEAR LEVER HANDBRAKEPOWER ASSISTED STEERING
To select reverse
(vehicle stationary)
Move the lever to neutral, then lift
up ring1against the gear lever knob
to select reverse gear.
The reversing lights illuminate as
soon as reverse gear is selected
(ignition on).
To release
Pull the lever up slightly, press in
button2and lower the lever to the
floor.
If you are driving with the
handbrake incorrectly released, the
red warning light on the instrument
panel will remain illuminated.
To apply
Pull the lever upwards.
The lever should travel about 10
notches to hold the vehicle. Your
vehicle has self adjusting rear brake
shoes and the handbrake should
only be adjusted during a brake
overhaul.
When the vehicle is
stationary, make sure
that the handbrake is
properly applied so that
the vehicle does not move
unintentionally.
Make sure the handbrake is
properly released when driving,
otherwise overheating may
occur.Never leave the steering on full lock
when the vehicle is parked (risk of
damaging the power assisted
steering pump).
Never switch off the
engine when travelling
downhill, and avoid
doing so when driving in
general (power steering and
brake servo will not function).

QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page20
2.20
ANTI-LOCK BRAKING SYSTEM (ABS)
When braking sharply, the two main
aims are to reduce the stopping
distance and to keep the vehicle
under control. However, depending
on the nature of the ground, the
atmospheric conditions and your
reactions, dangers due to loss of
adherence may exist: the wheels
may lock and directional control
may be lost. To avoid these risks,
your vehicle has been fitted with
the anti-lock braking system (ABS).
The safety enhancement is that the
brake control system prevents the
wheels from locking, even if the
brakes are applied too sharply,
allowing the vehicle to be steered
and thus its direction to be controlled.
Under these circumstances, it is quite
possible for the driver to steer the
vehicle and avoid an obstacle whilst
at the same time applying the brake.
This system also allows stopping
distances to be improved, especially
when adhesion is limited (wet roads,
slippery or uneven road surface).Although this system allows this
optimisation, the ABS system in no
way increases performance which is
physically related to the local
adherence conditions between the
tyres and the ground. You must still
follow the rules of good driving
practice (driving at a safe distance
from the vehicle in front etc.).The
fact that the vehicle’s safety has been
increased should not encourage you
to take risks.
Each time the system is activated,
you will feel a certain degree of
pulsation at the brake pedal. These
tangible signs will warn you that the
adhesion between the tyres and the
ground has reached its limit and
enable you to adapt your driving
style to suit the road conditions.Operating incidents
Two situations must be considered:
1 - The warning light is
illuminated on the instrument
panel.
Braking is still assured, but
without the action of the ABS
system. Consult a Renault Dealer
as soon as possible.
2 - The warning lights
are illuminated on the instrument
panel.
This indicates a fault in one of
the ABS braking components.
Braking may be partially assured.
It is howeverdangerous to brake
sharply,soyoumuststop
immediately as soon as traffic
conditions allow. Call for the
assistance of a Renault Dealer as
soon as possible.
The braking modulation provided by the ABS system is independent of the force applied at the pedal. In an
emergency, applyfirm, continuous pressureat the brake pedal - there is no need to pump it repeatedly.

2
1
3
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page28
2.28
ELECTRONIC STABILITY PROGRAM: ESP(continued)
Disabling the function
The function is deactivated by
pressing switch2, warning light1
will light up to confirm this.
This action also deactivates traction
control: see the information on the
traction control system in section 2.As the ESP offers additional safety,
it is recommended that you do not
drive when the function is disabled.
Correct this as soon as possible by
pressing button2again.
Note:ESP is automatically
reactivated when the ignition is
switched on.
Faults
When the system detects an
operating fault, warning lights1
and3light up.
Consult your Renault Dealer.

2
1
3
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T2.WIN 30/10/2002 12:06-page30
2.30
TRACTION CONTROL SYSTEM(continued)
Disabling the function
In some situations (driving on very
wet ground: snow, mud,... or
driving with chained wheels), the
system may reduce the engine
power to limit skidding. It is
possible to deactivate the function
by pressing switch2if this is not
desirable.
Warning light1lights up.Disabling the traction control
function also deactivates the ESP
function: refer to the information on
the ESP in section 2.
Correct this as soon as possible by
pressing switch2again.
Note:traction control is
automatically reactivated when the
ignition is switched on.
Operating faults
When the system detects an
operating fault, warning lights1
and3light up.
Consult your Renault Dealer.

1
3
2
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T5.WIN 30/10/2002 12:27- page 5
5.05
CHANGING A WHEEL
•Remove the wheel embellisher
(see section on embellishers).
• Use the wheelbrace1to loosen
the wheel bolts slightly. Fit it so
that you press downwards and
not upwards.
• Offer up the jack horizontally, the
jack head must be slid
underneath the jacking point
under the body, nearest the wheel
concerned.
• Screw up the jack by hand at first
to align the base plate (which
should be inclined further
inwards than the jack head). Use a
piece of wood under the base
plate if on soft ground.• Insert the end of the wheelbrace2
into the jack3and turn a few
times to lift the wheel off the
ground:
• Remove the bolts.
• Take off the wheel.
• Position the emergency spare
wheel on the central hub and turn
it to locate the mounting holes in
the wheel and the hub.
• Tighten the bolts and lower the
jack.
• Tighten the bolts fully when the
wheel is on the ground.Park your vehicle on firm,
flat ground (if necessary,
placing a plank under the
base of the jack).
Switch on the hazard warning
lights.
Apply the handbrake and engage a
gear (first or reverse, orPon an
automatic gearbox).
Ask all the passengers to get out of
the vehicle and keep them away
from moving traffic.
If you have a puncture,
replace the wheel as soon
as possible.
A tyre which has been
punctured should always be
inspected (and repaired if possible)
by a specialist.

QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T5.WIN 30/10/2002 12:28-page23
5.23
FUSES(continued)
Allocation of fuses
(the presence of fuses depends on the vehicle equipment level)
Symbol Allocation
Air bag/Central timer
Stop lights
Heated rear screen
Windscreen wipers
Anti-lock braking (ABS)
Fan
Radio/Cigar lighter/Clock
Horn
Left hand
dipped headlight
Right hand
dipped headlight
Symbol Allocation
Right hand main beam
headlight
Left hand main beam
headlight
Dual headlights
(dipped beam headlights
and main beam
headlights)
Heated rear view mirrors
Front fog lights
Not used
Not used
Central timer
Direction
indicators/Hazard warning
lights
Rear fog light
Symbol Allocation
Left hand side light
Right hand side light
Engine immobiliser
Interior and luggage
compartment lights/Radio
Central door locking
Electric windows
Headlight washers
Heated seats
Electric sunroof