remove seats RENAULT CLIO 2003 X65 / 2.G Owners Manual

11
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T1.WIN 4/11/2002 13:44-page18
1.10
REAR HEAD RESTRAINTS
To adjust the height
Simply slide it up.
To remove it
Press tab1.
To refit the headrest
Insert the rods into the sleeves, with
the notches to the front, and lower
the headrest to the desired height.Storage position
When the headrest is fully lowered,
it is in the storage position;do not
use this position when someone is
sitting in the rear seats.
The head restraint is
important for safety: ensure
that it is positioned
correctly. The distance
between your head and the head
restraint should be as small as
possible, and the top of the head
restraint should be as close as
possible to the top of your head.

QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T1.WIN 4/11/2002 13:45-page33
1.25
CHILD SAFETY(continued)
Age of child
(weight of child)All versions (except utility version)
Front passenger seat
(2)Rear side
seatsRear centre
seat
Birth to approximately 9 months
(weight below 13 kg)I(4) U-I X
From 9 months to approximately
3 years (weight from 9 to 18 kg)I(4) U-I(3) X
From 3 years to approximately
12 years(1)(weight from 15 to 36 kg)XU(3)X
X : seat not suitable for fitting a child seat for this age range.
U : seat suitable for fitting a belt-fitted child seat classed as universal for this age range, check that it can be fitted.
I : seat equipped with anchoring points for mounting a seat for this age range using Isofix locks, only RENAULT seats are
approved.
(1) A child taller than 1.50 m or weighing more than 36 kg can be strapped in the same way as an adult, without a special
seat.
(2) Only a rear-facing child seat may be installed in this seat.
(3) Place the back of the child seat against the vehicle seatback, adjust the headrest height or remove it if necessary.
(4)DANGER RISK OF DEATH OR SERIOUS INJURY: CHECK THAT THE FRONT PASSENGER AIRBAG HAS
BEEN DEACTIVATED BEFORE INSTALLING A REAR-FACING CHILD SEAT IN THIS SEAT.
(Refer to the Deactivating the front passenger Airbag information in Section 1 of the basic manual).

3
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T1.WIN 4/11/2002 13:45-page36
1.28
CHILD SAFETY(continued)
Category 2 (15 to 25 kg) and
category 3 (22 to 36 kg)
To correctly secure the pelvis of a
child of up to 12 years old, smaller
than 1.50 m and weighing less than
36 kg, it is preferable to use child
seats that can be combined with
three-point seat belts. This is a
booster seat (figure 3) with belt
guides to ensure that the belt will be
worn flat over the thighs of the
child.A booster seat with a
height-adjustable seatback and a
belt guide are recommended as this
will allow the belt to be worn as
close to the base of the neck as
possible but not on it.
Place the head rest in the top
position to allow you to press the
seat back of the child seat firmly
against the vehicle seatback.
If a booster seat without a seatback
is used, the vehicle's headrest will
have to be adjusted to suit the
child's stature; the upper edge of the
headrest must be at the same height
as the top of the child's head and
should never be lower than in line
with the child's eyes.
The standard classifies the
restraints in five categories:Category 0 : from 0 to 10 kg (0 to 22 lbs)
Category0+:from0to13kg(0to28lbs)
Category 1 : from 9 to 18 kg (20 to 40 lbs)
Category 2 : from 15 to 25 kg (33 to 55 lbs)
Category 3 : from 22 to 36 kg (48 to 80 lbs)
We recommend that you remove
the headrest and put it in the
luggage compartment, to facilitate
fitting certain types of child seat.

1
A
3
4
3
42
B
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T3.WIN 30/10/2002 12:12-page33
3.33
REAR BENCH SEAT(operation)
The seat base and the seatback may
be folded down (in one or two
sections) to allow bulky objects to
be carried
To fold down the seat base
Lift seat baseA, against the front
seats.
To fold down the seatback
Remove the rear head restraints (if
they are fitted to the vehicle). Press
button2and lower the seatbackB.
Removing the seat base
Lift the seat base to remove brackets3
from their housing4.
To refit the seat base,carry out the
operations in reverse order to
removal.Ensure the seat base is
correctly secured.
• When refitting the seatback, ensure it is correctly locked at the top. If seat covers are being used,
check that they are not preventing the seatback locking mechanism from operating correctly.
• When moving the bench seat, check that the seat belt housings1are correctly positioned before
folding down the seat base.
Once the bench seat is in place again, ensure the seat belts are correctly repositioned.