reset RENAULT CLIO 2003 X65 / 2.G Owners Manual

23HM
1
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T1.WIN 4/11/2002 13:45-page45
1.37
CLOCK / EXTERNAL TEMPERATURE
Clock1- setting the clock
With the ignition on, press button:
HFor hours,
MFor minutes.
Clock3, setting the time
With the engine switched on,
display3set to total mileage
recorder and clock function, press
and hold button2, to access time
setting mode, then release the
button.
There are two ways to set the time:
- one long press on button2allows
you to scroll through the hours
and minutes quickly;
- short presses on button2allow
you to set the time minute by
minute.If the electrical supply is cut
(battery disconnected, feed wire
broken, etc.), the clock must be
reset.
For your safety, we recommend
that you do not reset or alter the
time while driving.
External temperature
display1
The formation of ice is
related to exposure, local
hygrometry and temperature.
The external temperature alone is
not sufficient to detect ice.

QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T1.WIN 4/11/2002 13:45-page53
1.45
INSTRUMENT PANEL(continued)
or
The presence and operation of the warning lights, described below, depend on the vehicle equipment and
country.
6Speed limiter and
cruise control indicator
light
To understand how this
operates, refer to the
information on the cruise
control and speed limiter
functions in Section 2.
Toxic fume monitoring
warning light
For vehicles equipped
with this option, the light
comes on when the ignition is
switched on then goes out.
•Ifitlightsuppermanently,
consult your Renault Dealer
as soon as possible;
• If it flashes, reduce the
engine speed until the light
stops flashing.
Consult your Renault Dealer
as soon as possible.
Refer to the information on
anti-pollution, fuel economy
and driving in Section 2.6Over-revving warning lightIndicates that you need
to change gear.
LPG mode operating
indicator
Refer to the LPG-powered
vehicles supplement.
7Multifunction display
Oil level display function
The vehicle must be parked on
level ground and the engine
shouldhavebeenswitchedoff
for some time beforehand to
obtain an accurate level
reading.
When the ignition has been
switched on for approximately
30 seconds:
-if the level is correct,the
display will show “oil OK”
- when the minimum oil level
is reached:the word “OK”
will no longer be displayed,
the dashes and the word
“Oil” will flash and the SERV
warning light will light up
until the engine is switched
off.
It is vital to top up as soon as
possible.7Total mileage recorder, trip
mileage and clock
Can be read approximately
30 seconds after the ignition is
switched on.
8Multifunction key
Press the key repeatedly to
select information on the
display, to reset the trip mileage
recorder or to set the clock.

1
3
2
QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T1.WIN 4/11/2002 13:45-page58
1.50
ON-BOARD COMPUTER
1Display
2General reset and trip mileage
recorder reset button
To reset the trip mileage recorder,
the display must show the “trip
mileometer” function.
Automatic reset
Automatic resetting will occur
when the maximum of any of the
memories is exceeded.3Display selection key
Press button3repeatedly to
scroll through the following
information:
a) total mileage recorder,
b) trip mileage recorder,
c) fuel used,
d) average consumption,
e) current consumption,
f) estimated range,
g) distance covered,
h) average speed,
i) recommended speed (speed
limiter/cruise control).
Refer to the chart on the following
page for display examples.
Interpreting certain values
displayed after a reset:
The values showing average fuel
consumption, range and average
speed will become more stable
and reliable the further you travel
since the last time the reset key
was pressed.In the first few miles after resetting,
you may notice:
• that the range increases as you
drive. This is normal as the
average consumption may reduce
when:
- the vehicle is no longer
accelerating,
- the engine reaches normal
operating temperature (reset
when engine was cold),
- you drive from a built up area to
the open road.
If average consumption is
decreased, the expected range
will therefore increase.
• average consumption increases
when the vehicle is stationary
and idling.
This is normal as the computer
takes into account the fuel used
during idling.

QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T1.WIN 4/11/2002 13:45-page59
1.51
ON-BOARD COMPUTER(continued)
Examples of
display selections by
pressing button3Interpreting the display
a) Total mileage recorder.
b) Trip mileage recorder.
c) Fuel used(in litres or gallons) since the last reset.
d) Average consumption(in mpg or l/100 km) since the last reset.
The value is displayed after covering 400 metres taking into account the
distance covered and the fuel used since the last reset.

QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T1.WIN 4/11/2002 13:45-page60
1.52
ON-BOARD COMPUTER(continued)
Examples of
display selections by
pressing button3Interpreting the display
e) Current consumption(in mpg or litres/100 km)
The value is displayed after reaching a speed of 15 mph (25 km/h).
f) Estimated range with remaining fuel(in miles or km)
This function uses the average consumption since the last general reset.
The value is displayed after covering 400 metres.
g) Distance covered(in miles or km) since the last reset.
h) Average speed(in mph or km/h) since the last reset.
The value is displayed after covering 400 metres.
i) Cruise control or speed limiter recommended speed(depending on
vehicle).
See the information on speed limiter and cruise control in section 2.

QXBIUDB*T[G      3DJH 
nu654-6 - CLIO IIC:\Documentum\Checkout
u654-6_eng_T4.WIN 28/10/2002 11:44- page 3
4.03
ENGINE OIL LEVEL
An engine uses oil for lubrication
and to coolmoving parts and it is
sometimes necessary to top up the
level between oil changes.
However, consult your Renault
Dealer if more than 0.5 litre is
being consumed every 625 miles
(1000 km) after the running-in
period.
Oil change frequency: Check the oil
level from time to time and always
before long journeys, to avoid the
risk of damaging your engine.
Reading the oil level
The car must be parked on level
ground and the engine should have
been switched off for some time
beforehand to obtain an accurate
reading.
The oil level can be read:
- on the instrument panel;
- using the dipstick.Reading the level on the instrument
panel
When ignition has been switched
on for approximately 30 seconds:
-if the level is correct, the display
will show “oil OK”: display
message1
Special note:To gain a more
precise indication of the level,
press the trip mileage counter
reset button or the information
scroll button on the on-board
computer.The squares which appear on the
display indicate the level. The
number of squares displayed
decreases as the oil level drops and
they are replaced by a dash: display
message2.
To move to on-board computer
reading, press the button again.
-When the minimum oil level is
reached,the dashes and the word
“Oil” flash, and the word “OK”
disappears (display message3)
and some versions
lights up on the instrument panel.
It is vital to top up the oil as soon
as possible.
Message 1
Level
satisfactory
Message 2
Level
display
function
Message 3
Minimum
level
(flashing)