fold seats RENAULT GRAND SCENIC 2015 J95 / 3.G Owners Manual

1.16
Heated seats(depending on vehicle)
With the engine running, turn control 6
to either position 1, 2 or 3 (depending
on the temperature required). The mes-
sage “Heated activated” will appear on
the instrument panel once the front seat
heating system is operating.
The system, which has a thermostat,
decides whether or not the heating is
needed, according to the position se-
lected.
FRONT SEATS WITH MANUAL CONTROL (2/2)
Table function
Depending on the vehicle, the passen-
ger seatback may be folded down onto
the seat base to create a table.
Lower the headrest if necessary, tilt
handle 5 and completely lower the
seatback.
65
When the front seat is in
table position, the front pas-
senger air bag must be dis-
abled (see information on
“Activating/deactivating the front
passenger air bag” in Section 1).
Risk of serious injury caused by
items resting on the seatback table
which may be dislodged when the
air bag is deployed.
The label (on the dashboard) and
the markings (on the windscreen)
remind you of these instructions.
For your safety, attach any
transported objects when
the seat is in the table po-
sition.

3.27
To fold down a seatback (table posi-
tion)
Lower headrest 3.
Lift handle 4 or, depending on the vehi-
cle, pull tab 1.
An occasional table position can be
created by folding the seatback all the
way down onto the seat cushion.
The seats can hold up to 80 kg in this
position.
For safety reasons, carry
out any adjustments when
the vehicle is stationary.
The rear seats are separate seats.
To move the seats forwards or
backwards
Lift lever 2 to unlock the seat. Once in
the desired position, release the lever
and check that the seat is correctly
locked.
ADJUSTING THE REAR SEATS
33
When moving the rear
seats, ensure that nothing
obstructs the anchorage
points (passenger’s arm or
leg, a pet, gravel, cloth, toys, etc.).
To tilt the seatback
Lift handle 4 or pull strap 1 and tilt the
seatback to the desired position.
2
1
414

3.28
Folding up a seat
Lower the headrest.
Seat with control 2
Lift the control 2, the seatback is low-
ered and lift the seat as far forwards as
possible.
Seat without control 2
Lift control 1 or pull belt 3 and tilt the
seatback into the table position. Then,
lift control 4 or pull belt 5 and lift the
seat as far forwards as possible.
REAR SEAT FUNCTIONS (1/2)
Returning a seat to its normal
position
Lower the seat until it locks in place at
floor level (movement A).
Check that it is correctly locked.
When moving the rear
seats, ensure that nothing
obstructs the anchorage
points (passenger’s arm or
leg, a pet, gravel, cloth, toys, etc.).
2
13
4
Note: it may be necessary to move
the passenger and/or driver’s seats
forwards and to lower the seatback in
order to tilt the seat as far forwards as
possible.
The seats can be folded down from the
rear of the vehicle on 7-seater vehicles.
Pull control 1 or belt 3 to tilt the seat-
backs, then tilt the seat by pulling belt 4.
11
For safety reasons, carry
out any adjustments when
the vehicle is stationary.
A
5

3.29
REAR SEAT FUNCTIONS (2/2)To fit a seat
Attach the hooks 8 to rail 7 marked 9 by
gently lifting the back of the seat.
Tilt the seat as far forward as possible,
movement B (handle 6 locks in place).
Note: it may be necessary to move
the passenger and/or driver’s seats
forwards and to lower the seatback in
order to tilt the seat as far forwards as
possible.
Lower the seat until it locks in place at
floor level.
Check that it is correctly locked.
When fitting side seats, make sure
that the seat belt buckle is inside the
vehicle.
To remove a seat
With the seat folded down, gently lower
it while lifting handle 6.
Release the handle and guide the seat
to the floor.
Remove the seat from the vehicle by
lifting it.
Once the rear seats have been re-
moved, ensure that they are rested
on a flat surface so as not to damage
the units under the seats (depend-
ing on the vehicle).
When refitting the seat-
back, make sure it is cor-
rectly locked in place.
If seat covers are fitted ,
make sure these do not prevent the
seatback latch from locking in.
Make sure that the seat belts are
positioned correctly.
Reposition the headrests.
When driving with the seats
folded down: ensure you
check that the seats are
moved fully forward before
folding them down and place the
load as close as possible to prevent
the seats from falling back when ac-
celerating or during sudden braking.
6
B
6
8
7
9

3.30
To unfold a seat
– From the luggage compartment, remove the luggage cover and store
it (refer to the information on the “lug-
gage cover: long chassis versions” in
Section 3);
– pull strap 2, lock the seat by pull-
ing on the top of the seatback and
ensure that it is correctly locked in
place;
– fit the headrest.Third row rear seats
Folding up a seat
– From the luggage compartment, lower the headrest;
– pull strap 2;
– push the seatback (areas A) to lock
the seat, ensuring that it is correctly
locked.
Note: the hooks 1 secure the seat belt
buckles.
REAR SEAT OPERATION: 7-seater version (1/2)
When moving third row rear
seats:
– check that no one is near
to any of the moving parts;
– check that there is sufficient space around the seat;
– check that nothing obstructs the section of the luggage compart-
ment reserved for storing the
seat.
For safety reasons, carry out any
adjustments when the vehicle is sta-
tionary.
2
AA
1
2
AA
1

3.31
REAR SEAT OPERATION: 7-seater version (2/2)
Accessing the third row rear
seats
– Via the rear doors, push the second row seat forwards;
– lower the seat headrest;
– lift handle 3; the seatback lowers
itself. Fold the seat down;
– sit in the third row rear seat; – pull the second row rear seat to put it
into the table position;
– lift the seatback.
Use restriction
It is not permitted to drive with a second
row rear seatback or seat folded down
when there is a passenger occupying a
third row rear seat.
The label located on the back of the
seats reminds you of this.
3

3.37
Always place the objects to be trans-
ported so that their largest side rests
against the back of the rear bench seat,
for normal loads (example A) or against
the back of the front seats B when the
rear bench seatbacks are folded down.
If you have to place objects on the
folded seat back, it is vital that you
remove the headrests before folding
the seat back so that it can be folded as
flat as possible against the seat.
TRANSPORTING OBJECTS IN THE BOOT (1/2)
A
Always position the heavi-
est items directly on the
floor. Use the lashing points
on the floor of the luggage
compartment, if these are fitted to
the vehicle. The luggage should be
loaded in such a way that no items
will be thrown forward and strike the
occupants if the driver has to brake
suddenly. Fasten the rear seat belts,
even if the seats are not occupied.
B