stop start RENAULT KANGOO 2012 X61 / 2.G Owner's Manual

3.8
ENG_UD10847_2
Air conditionné automatique (X61 - F61 - K61 - X61 BUp - Renault)
ENG_NU_813-11_FK61_Renault_3
Jaune NoirNoir texte
Only the temperature and the AUt O
symbol are displayed
Functions managed in automatic mode
are not displayed.
– press button 6 to increase the tem -
perature;
– press button 3 to decrease the tem-
perature.
n ote: The maximum and minimum
settings of 15°C and 27°C allow the
system to produce a minimum or maxi-
mum temperature, whatever the ambi-
ent conditions.
In automatic mode (AUTO indicator
light on the display is lit), all air con-
ditioning functions are controlled by
the system.
When you modify certain functions
the AUTO indicator light goes out.
Only the modified function stops
being controlled by the system.
To reach and keep the chosen comfort
level and to maintain good visibility, the
system controls:
– ventilation speed;
– air distribution;
– air recirculation management;
– air conditioning start/stop;
– the air temperature.Automatic mode
Press button 5 . The AUTO operating
tell-tale will come on.
The automatic climate control system
guarantees comfort in the passen -
ger compartment and good visibility
(except in the event of extreme condi -
tions), while optimising fuel consump -
tion.
t his is the recommended mode of
use.
AUt OMA tiC CLiMA te COntrOL (2/8)
365

bonnet................................................... (up to the end of the DU)
maintenance: mechanical ...................................... (up to the end of the DU)
4.2
ENG_UD25823_5
Capot moteur (X61 - F61 - K61 - Renault)
ENG_NU_813-11_FK61_Renault_4
Jaune NoirNoir texte
To open, pull handle 1 , located on the
left-hand side of the dashboard.Unlocking the bonnet catch
Lift the bonnet by several centimetres
and push lever 2 to the left.
Bonnet
Bonnet (1/2)
The engine may be hot
when carrying out opera -
tions in close proximity. In
addition, the engine cooling
fan can come on at any moment.
Risk of injury.
1
2
In the event of an impact,
even slight, against the ra -
diator grille or bonnet, have
the bonnet catch checked
by an approved dealer as soon as
possible.
4
5
3
Deactivate the Stop and
Start function for any opera -
tion performed in the engine
compartment.
opening the bonnet
Lift the bonnet up and release stay 4
from its holder 5 . For your own safety,
it is very important to fit the stay into
its retainer 3 . Check that it is correctly
locked.

JauneNoirNoir texte
4.5
ENG_UD25824_5
Niveau huile moteur : généralités (X61 - F61 - K61 - Renault)\
ENG_NU_813-11_FK61_Renault_4
exceeding the maximum
engine oil level
The oil level should only be read with
the dipstick as explained above.
If the oil level exceeds the maximum
level, do not start your vehicle and
contact an approved Dealer.
Consult your approved Dealer at
once if you notice an abnormal or
repeated drop in any of the fluid
levels.
The engine may be hot
when carrying out opera -
tions in close proximity. In
addition, the engine cooling
fan can come on at any moment.
Risk of injury.
Under no circumstances
should maximum filling
level B be exceeded: this
could damage the engine
and the catalytic converter.
In order to prevent splashback, it is
recommended that a funnel be used
when topping up/filling with oil.
engIne oIl level: general information (2/2)
Reading the level using the
dipstick
Engine switched off:
– remove the dipstick and wipe with a
clean, lint-free cloth;
– push the dipstick in as far as it will
go;
– take out the dipstick again;
– read the level: it should never fall
below minimum mark A or exceed
maximum mark B.
Once the level has been read, push the
dipstick in as far as it will go.
A
B
A
B
Deactivate the Stop and
Start function for any opera -
tion performed in the engine
compartment.

levels .................................................... (up to the end of the DU)
levels: brake fluid ........................................................ (current page)
brake fluid .............................................................. (current page)
4.8
ENG_UD25825_5
Niveaux / Filtres (X61 - F61 - K61 - Renault)
ENG_NU_813-11_FK61_Renault_4
Jaune NoirNoir texte
Levels
levelS (1/3)
Brake fluid level
This should be checked frequently,
and immediately if you notice even the
slightest loss in braking efficiency.
The level should be read with the engine
switched off and on level ground. level 1
It is normal for the level to drop as the
brake shoes become worn, but it must
never drop lower than the
“MInI" warn-
ing line.
If you wish to check the disc and drum
wear yourself, you should obtain the
document explaining the checking pro-
cedure from our network or from the
manufacturer’s website. t
opping up
After any operation on the hydraulic cir-
cuit, a specialist must replace the fluid.
Only use fluids approved by our
Technical Department (and taken from
a sealed container).
Replacement intervals
Refer to the Maintenance Document for
your vehicle.
The engine may be hot
when carrying out opera -
tions in close proximity. In
addition, the engine cooling
fan can come on at any moment.
Risk of injury.
1
Consult your approved dealer at
once if you notice an abnormal or
repeated drop in any of the fluid
levels.Deactivate the Stop and
Start function for any opera -
tion performed in the engine
compartment.

levels:windscreen washer reservoir ........................... (current page)
filter ........................................................................\
(current page)
windscreen washer fluid ........................................ (current page)
4.10
ENG_UD25825_5
Niveaux / Filtres (X61 - F61 - K61 - Renault)
ENG_NU_813-11_FK61_Renault_4
levelS (3/3)/FIlteRS
Filters
Windscreen washer reservoir
t opping up
– Unscrew cap 3;
– fill until you can see the fluid;
– close the cap. liquid
Screen wash product (product with
antifreeze in winter).
Jets
To adjust the height of the windscreen
washer jets, use a tool such as a flatb-
lade screwdriver.
Filters
The replacement of filter elements (air
filter, cabin filter, diesel fuel filter, etc.)
is scheduled in the maintenance opera
-
tions for your vehicle.
Replacement intervals for filter el -
ements: refer to the Maintenance
Document for your vehicle.
The engine may be hot
when carrying out opera -
tions in close proximity. In
addition, the engine cooling
fan can come on at any moment.
Risk of injury.
3
Deactivate the Stop and
Start function for any opera -
tion performed in the engine
compartment.

battery................................................... (up to the end of the DU)
4.11
ENG_UD26568_4
Batterie (X61 - F61 - K61 - Renault)
ENG_NU_813-11_FK61_Renault_4
It does not need to be serviced; never
open cover 1 on the battery.
Battery
Handle the battery with care
as it contains sulphuric acid,
which must not come into
contact with eyes or skin. If
it does, wash the affected area with
plenty of cold water. If necessary,
consult a doctor.
Ensure that naked flames, red hot
objects and sparks do not come into
contact with the battery as there is a
risk of explosion.
BA tteR y (1/2)
Depending on the vehicle, a system
continuously checks the battery charge
status.
When the ignition is off, some consum-
ers may also be switched off (dipped
beam headlights, radio, ventilation,
etc.). On the instrument panel, the
message “battery saving mode” or “batt
save” appears when they are switched
off . When the level is extremely low,
the message “low battery, start engine”
is displayed.
The charge status of the battery can
decrease, especially if you use your ve-
hicle:
– for short journeys;
– for driving in town;
– when the temperature drops, etc.;
– with the vehicle stopped and the
engine off.
The engine may be hot
during operations in close
proximity. In addition, the
engine cooling fan may
start at any moment.
Risk of injury.
1
label A
Observe the indications on the battery:
– 2 naked flames and smoking are
prohibited;
– 3 eye protection required;
– 4 keep away from children;
– 5 explosive materials;
– 6 please consult the driver’s hand -
book;
– 7 corrosive materials.
A234
567

4.12
ENG_UD26568_4
Batterie (X61 - F61 - K61 - Renault)
ENG_NU_813-11_FK61_Renault_4
BA tteR y (2/2)
Replacing the battery
As this operation is complex, we advise
you to contact an approved Dealer.
v ehicle fitted with the Stop and Start
function
The function will have to be restarted
each time the battery is replaced. To
restart the function, press and hold the
Stop and Start activation/deactivation
switch 8 until you hear a beep.
The battery is a specific
type , please ensure it is
replaced with the same
type. Consult an approved
dealer.
8
Deactivate the Stop and
Start function for any opera -
tion performed in the engine
compartment.

JauneNoirNoir texte
5.5
ENG_UD29751_1
Kit de gonflage des pneumatiques (2 kits) (X61 - F61 - K61 - Renault)\
ENG_NU_813-11_FK61_Renault_5
Once the tyre is inflated correctly:
– stop using the kit;
– close the integrated cap on the bottle
again;
– disconnect adapter 8;
tyre InFlatIOn KIt (3/5)
– affix the driving recommendation
label 10 to the dashboard where it
can easily be seen by the driver;
– store the kit;
– at the end of this initial inflation op -
eration, air will still escape from the
tyre; you must drive a short distance
in order to seal the hole;
– start immediately and drive at be -
tween 12 and 40 mph (20 and
60 km/h) in order to distribute the
product evenly in the tyre and, after
driving for 2 miles, stop and check
the pressure;
– if the pressure is greater than 1.3 bar
but less than the recommended
pressure (refer to the label affixed to
the edge of the driver’s door), read-
just it; otherwise, please contact an
authorised dealer: the tyre cannot be
repaired.
n ote: after using the inflation kit, you
should visit an approved Dealer to re -
place the inflation hose and the bottle
of repair product.
Following repair with the kit,
do not travel further than
120 miles (200 km). In addi -
tion, reduce your speed and
under no circumstances exceed
48 mph (80 km/h). The label, which
you must affix in a prominent posi -
tion on the dashboard, reminds you
of this. Depending on the country or
local legislation, a tyre repaired with
the tyre pressure kit will need to be
replaced.
Nothing should be placed
around the driver ’s feet
as such objects may slide
under the pedals during
sudden braking manoeuvres and
obstruct their use.
10
8
Please be aware that a
poorly tightened or miss -
ing valve cap can make the
tyres less airtight and lead
to pressure loss.
Always use valve caps identical to
those fitted originally and tighten
them fully.
Precautions when using the
kit
The kit should not be operated for more
than 15 consecutive minutes.
e

JauneNoirNoir texte
5.7
ENG_UD29751_1
Kit de gonflage des pneumatiques (2 kits) (X61 - F61 - K61 - Renault)\
ENG_NU_813-11_FK61_Renault_5
tyre InFlatIOn KIt (5/5)
Precautions when using the kit
The kit should not be operated for more
than 15 consecutive minutes.
Nothing should be placed
around the driver ’s feet
as such objects may slide
under the pedals during
sudden braking manoeuvres and
obstruct their use.
Please be aware that a
poorly tightened or miss -
ing valve cap can make the
tyres less airtight and lead
to pressure loss.
Always use valve caps identical to
those fitted originally and tighten
them fully.
Following repair with the kit,
do not travel further than
120 miles (200 km). In addi -
tion, reduce your speed and
under no circumstances exceed
48 mph (80 km/h). The sticker,
which you must affix in a prominent
position on the dashboard, reminds
you of this.
Depending on the country or local
legislation, a tyre repaired with the
inflation kit may need to be replaced.
11
If a minimum pressure of 1.8 bar is
not reached after 15 minutes, repair
is not possible; do not drive the ve-
hicle but contact an approved dealer. Once the tyre is correctly inflated,
remove the kit: slowly unscrew the in
-
flation adapter 11 to prevent any repair
product from escaping and store the
container in plastic packaging to pre -
vent the product from escaping.
– Affix the driving recommendation
label to the dashboard where it can
easily be seen by the driver;
– Put the kit away.
– At the end of this initial inflation op-
eration, air will still escape from the
tyre. You must drive a short distance
in order to seal the hole.
– Start immediately and drive at be -
tween 12 and 40 mph (20 and
60 km/h) in order to distribute the
product evenly in the tyre and, after
driving for 2 miles (3 km), stop and
check the pressure.
– If the pressure is greater than 1.3 bar
but less than the recommended
pressure (refer to the label affixed to
the edge of the driver’s door), read-
just it. Otherwise, please contact an
authorised dealer: the tyre cannot be
repaired.
F

bulbschanging ......................................... (up to the end of the DU)
changing a bulb .................................... (up to the end of the DU)
front lights changing bulbs ................................ (up to the end of the DU)
bulbs changing ......................................... (up to the end of the DU)
lights: dipped beam headlights ................................... (current page)
lights changing bulbs ................................ (up to the end of the DU)
lights front ................................................. (up to the end of the DU)
5.15
ENG_UD25826_4
Projecteurs : remplacement des lampes (X61 - F61 - K61 - Renault)
ENG_NU_813-11_FK61_Renault_5
Headlights: changing bulbs
The bulbs are under pres -
sure and can break when
replaced.
Risk of injury.
Dipped beam/main beam
headlights
Turn cover 1 a quarter of a turn to
unlock it.
Disconnect the wiring.
Remove rubber protector 2.
Unclip spring 3 to remove the bulb.
lIghts: changing bulbs (1/2)
1
2
3
Do not touch the bulb glass. hold it
by its base.
To refit it, carry out the above opera -
tions in reverse order.
Ensure that rubber protector 2 is re -
positioned correctly so that the three
strips can be seen.
The engine may be hot
during operations in close
proximity. In addition, the
engine cooling fan may
start at any moment.
Risk of injury.
Deactivate the Stop and
Start function for any opera -
tion performed in the engine
compartment.
Bulb type: h4
It is essential to use 55W anti UV bulbs
to prevent damage to the lights' plastic
glass.