lock RENAULT KANGOO 2013 X61 / 2.G Access Security User Guide

82D-30V1 MR-376-X76-82D000$140.mif
82D
UCH
Vdiag No.: 0F
Tool command Diagnostic tool name Comments
AC004Central door locking Refer to the interpretation of the command.
AC005Central door unlocking Refer to the interpretation of the command.
AC006Driver's door unlocking Refer to the interpretation of the command.
AC136Remote locking buzzer Refer to the interpretation of the command.
SC003Spare Refer to the interpretation of the command.
SC015Key allocation Refer to the interpretation of the command.
ACCESS - SECURITY
Fault finding – Command summary table

82D-31
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-82D000$150.mif
82D
UCH
Vdiag No.: 0F
AC004
AC005
AC006OPENING ELEMENT LOCKINGOPENING ELEMENT UNLOCKING
DRIVER'S DOOR UNLOCKING
NOTESThere must be no present or stored faults.
This command is for testing locking relay operation.
This command lasts for 2 seconds.
Special Note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check the condition and connection of the UCH connector, component code 645.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the condition and connection of the connectors of the components: driver's door central locking,
component code 140, passenger door central locking, component code 141, luggage compartment lid central
locking, component code 142 and side door central locking computer, component code 1200 (depending on
version).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity, insulation and the absence of interference resistance on the following connections:
Driver's door electric lock:
–20AU between components 140 and 645,
–20D between components 140 and 645.
UCH_V0F_AC004/UCH_V0F_AC005/UCH_V0F_AC006
ACCESS - SECURITY
Fault finding – Interpretation of commands

82D-32
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-82D000$150.mif
ACCESS - SECURITY
Fault finding – Interpretation of commands82D
UCH
Vdiag No.: 0F
AC004
AC005
AC006
CONTINUED
Passenger door electric lock:
–20C between components 141 and 645,
–20D between components 141 and 645,
Boot lid electric lock:
–20C between components 142 and 645,
–20D between components 142 and 645,
Side door central locking (depending on version):
–20C between components 1200 and 645,
–20D between components 1200 and 645,
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the techline.

82D-36
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-82D000$150.mif
ACCESS - SECURITY
Fault finding – Interpretation of commands82D
UCH
Vdiag No.: 0F
Key allocation procedure
– Establish dialogue with the UCH.
– Select the Repair mode menu.
– Select the Programming menu.
– Select line SC015 Allocate key.
The key allocation procedure takes place in two stages:
1. Key insertion stage.
2. Key allocation stage.
1- Key insertion stage
Clip requires that the keys to be allocated are inserted.
Insert ALL the keys to be allocated (old and new blank keys). Any keys not inserted at this stage will be rejected at
the Key allocation stage and the operation will have to be restarted from the beginning.
Once all the keys are inserted, the Clip diagnostic tool displays the programming key in "not connected" mode.
To obtain the immobiliser code, (see Technical Note 5037A, Code delivery procedure).
2- Key allocation stage:
Continue the procedure following the instructions on the Clip diagnostic tool.
Once the keys have been allocated, make sure that all the keys can lock and start the vehicle.
SC015
CONTINUED 2
IMPORTANT
In "not connected" mode, the programming key can only be used for a limited amount of time, as indicated by the
CLIP diagnostic tool. After this time, the programming key and associated immobiliser code are no longer valid.
The operation must be restarted from the beginning.

82D-37V1 MR-376-X76-82D000$160.mif
82D
UCH
Vdiag No.: 0F
Starting fault
NOTESOnly refer to these customer complaints after carrying out a complete check with
the diagnostic tool
The vehicle will not startALP 7
No electric window operationALP 8
The electric door locking/unlocking control operates erratically ALP 9
ACCESS - SECURITY
Fault finding – Customer complaints

82D-38
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V1 MR-376-X76-82D000$170.mif
82D
UCH
Vdiag No.: 0F
ALP 7 The vehicle will not start
NOTESOnly refer to the customer complaints after performing a complete check using
the diagnostic tool.
Does the central locking operate?See 87B, Passenger compartment
connection unit.
Switch on the ignition. Has the immobiliser
warning light gone out?
Turn the starter.
Nothing happens.The starter clicks
but the engine
does not turn over.The starter motor
turns but there is
no engagement.The engine turns
but does not start.The engine turns
over progressively
more slowly and
does not start.
Perform an
injection domain
test using the
diagnostic tool.
See 13B, Diesel
Injection or 17B,
Petrol Injection.Check the battery
voltage. Check the
condition of the
starter.
NO
YES
NOA
YES
BCD
UCH_V0F_ALP07
ACCESS - SECURITY
Fault finding – Fault finding chart

82D-41
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V1 MR-376-X76-82D000$170.mif
ACCESS - SECURITY
Fault finding – Fault finding chart82D
UCH
Vdiag No.: 0F
ALP 7
CONTINUED 3
Check the battery voltage when the starter is turning and check the earth straps connecting the engine and
transmission assembly to the vehicle chassis.
Check that the starter motor has not seized or locked.
If the fault is still present, replace the starter motor (see MR 374, Mechanical, 16A, Starting - Charging, Starter:
Removal - Refitting).
C

82D-47
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V1 MR-376-X76-82D000$170.mif
ACCESS - SECURITY
Fault finding – Fault finding chart82D
UCH
Vdiag No.: 0F
ALP 9 The electric door locking/unlocking control operates erratically
Check the condition and connection of the UCH connector, component code 645 and the electric door locking
control connector, component code 123.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
For locking:
Check the continuity and the insulation of the following connections:
–20A between components123 and 645,
–MK between components 123 and earth.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
A
UCH_V0F_ALP09

82D-48
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V1 MR-376-X76-82D000$170.mif
ACCESS - SECURITY
Fault finding – Fault finding chart82D
UCH
Vdiag No.: 0F
ALP 9
CONTINUED
For unlocking:
Check the continuity and the insulation of the following connections:
–20B between components123 and 645,
–MK between components 123 and earth.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
A