diagnostic menu RENAULT KANGOO 2013 X61 / 2.G Access Security Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2013, Model line: KANGOO, Model: RENAULT KANGOO 2013 X61 / 2.GPages: 48, PDF Size: 0.31 MB
Page 13 of 48
82D-13V1 MR-376-X76-82D000$050.mif
ACCESS - SECURITY
Fault finding – Configuration82D
UCH
Vdiag No.: 0F
Access and Safety function configurations in the UCH
Configuration readings available using the diagnostic tool:
*RAID: Renault Anti-Intruder Device.
*CPE: Electric central door locking.
• Check the configurations in the Read configurations menu Equipment required:
CLIP diagnostic tool
Configuration
readingName of configuration Option Configuration
LC012Automatic relockingWITH OR WITHOUT
SC008 UCH type LC097Type of keyONE BUTTON or
TWO BUTTONS
LC113AirbagWITH OR WITHOUT
LC170RAID* function authorisation by diag
toolWITH OR WITHOUT
LC171Radiofrequency functionWITH OR WITHOUT
LC172Type of central door locking button
(CPE)*1 POSITION or 2
POSITIONS
Page 14 of 48
82D-14V1 MR-376-X76-82D000$060.mif
82D
UCH
Vdiag No.: 0F
UCH PROGRAMMING PROCEDURE
The UCH programming procedure is carried out using the diagnostic tool.
– Establish dialogue with the UCH computer.
– In the menu Special commands, select the command SC004 Program UCH.
The tool displays Remove the key from the anti-theft switch,
The tool displays Please enter the After-Sales code. With the ignition off, enter the secret After-Sales code and
validate.
If the code format is correct, the tool displays Insert a key which has already been programmed to the vehicle
and the programming procedure starts.
The tool displays UCH programming completed, please start key programming procedure, the UCH is coded.
Enter key programming mode to allocate the other keys (maximum of three). Several seconds may elapse before
this message appears.
SPECIAL CASES
If the screen displays:
– The After Sales code entered does not correspond with the key inserted. Check that you have entered
the code correctly and you have inserted a key belonging to the vehicle:
– The code read is incorrect or the UCH has already been coded on another vehicle.
–The UCH is not blank. Please start the key programming procedure: The UCH has already been
programmed for this vehicle.
–Check the After-Sales code: the code entered is incorrect. Check, then try entering the data again,
–UCH programming failure, key cannot be used on this vehicle: the key code does not correspond to the
code entered (the key belongs to a vehicle from a different range).
–The key inserted is blank. Please insert another key which has already been programmed to this vehicle:
the key is blank. Insert a key which has already been coded on this vehicle. IMPORTANT:
The maximum delay time between each operation is 5 minutes, otherwise the procedure is cancelled.
Once the UCH is coded, it is impossible to clear it or program it with a new code.
ACCESS - SECURITY
Fault finding – Programming
Page 33 of 48
82D-33
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-82D000$150.mif
ACCESS - SECURITY
Fault finding – Interpretation of commands82D
UCH
Vdiag No.: 0F
This command is used to recover a code which will allow the Techline to supply the After-Sales code.
Recovery procedure for Spare code:
– Establish dialogue with the UCH.
– Select the menu Repair mode.
– Select the menu Programming.
– Select the line SC003 Spare.
Follow the instructions on the Clip diagnostic tool.
SC003SPARE
Equipment required
CLIP
UCH_V0F_SC003
Page 36 of 48
82D-36
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-82D000$150.mif
ACCESS - SECURITY
Fault finding – Interpretation of commands82D
UCH
Vdiag No.: 0F
Key allocation procedure
– Establish dialogue with the UCH.
– Select the Repair mode menu.
– Select the Programming menu.
– Select line SC015 Allocate key.
The key allocation procedure takes place in two stages:
1. Key insertion stage.
2. Key allocation stage.
1- Key insertion stage
Clip requires that the keys to be allocated are inserted.
Insert ALL the keys to be allocated (old and new blank keys). Any keys not inserted at this stage will be rejected at
the Key allocation stage and the operation will have to be restarted from the beginning.
Once all the keys are inserted, the Clip diagnostic tool displays the programming key in "not connected" mode.
To obtain the immobiliser code, (see Technical Note 5037A, Code delivery procedure).
2- Key allocation stage:
Continue the procedure following the instructions on the Clip diagnostic tool.
Once the keys have been allocated, make sure that all the keys can lock and start the vehicle.
SC015
CONTINUED 2
IMPORTANT
In "not connected" mode, the programming key can only be used for a limited amount of time, as indicated by the
CLIP diagnostic tool. After this time, the programming key and associated immobiliser code are no longer valid.
The operation must be restarted from the beginning.