seat memory RENAULT KANGOO 2013 X61 / 2.G Air Bags AC4 And Pretensioners Workshop Manual

88C-15
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-88C000$060.mif
88C
2nd generation
(AC4 phase II)
DF001
PRESENT
OR
STOREDCOMPUTER
1.DEF: Internal electronic fault
2.DEF: Impact detected
NOTESUse Wiring Diagrams Technical Note for Kangoo VLL.
Replace the airbag computer, component code 756 (consult the section "Replacement of components" for this
operation) (see MR Mechanical: MR-AIRBAGS-SRP, 88, Airbags and seat belt pretensioners, Computer:
Removal-refitting).
AIRBAGS AND PRETENSIONERS
Fault finding – Interpretation of faults

88C-17
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-88C000$060.mif
AIRBAGS AND PRETENSIONERS
Fault finding – Interpretation of faults88C
2nd generation
(AC4 phase II)
DF003
PRESENT
OR
STOREDDRIVER'S FRONTAL AIRBAG CIRCUITCC: Short circuit
CO: Open circuit
CC.1: Short circuit to 12 volts
CC.0: Short circuit to earth
NOTESNever carry out measuring operations on ignition lines using any tool other than Clip,
NXR or XRBAG.
Use Wiring Diagrams Technical Note for Kangoo VLL.
CO
CC
NOTESNone.
Lock the computer using the command on the diagnostic tool.
Switch off the ignition and remove the 2 mounting bolts from the steering wheel cushion.
Check that it is correctly connected.
Disconnect the steering wheel airbag and connect a dummy ignition module to the ignition module connector.
Switch on the ignition and carry out a check using the diagnostic tool.
Replace the airbag if the fault is now stored (fault no longer declared as present) (see MR Mechanical: MR-
AIRBAGS-SRP, 88, Airbags and seat belt pretensioners, Driver's airbag: Removal-refitting).
With the ignition switched off, disconnect and reconnect the connector of the rotary contact beneath the steering
wheel.
Check the connections if the fault has become stored (fault no longer declared present).

88C-25
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-88C000$060.mif
AIRBAGS AND PRETENSIONERS
Fault finding – Interpretation of faults88C
2nd generation
(AC4 phase II)
DF016
PRESENTCOMPUTER CONFIGURATION
NOTESThis fault may appear after using the passenger airbag locking command, by not
observing the procedure described in the Technical Note (this command allows a child
seat to be fitted on the passenger seat).
It is vital that you never use this passenger airbag locking command before a
Technical Note dealing with the subject has been distributed.
This fault corresponds to an inconsistency between the computer configuration and the vehicle equipment
detected by the computer. The computer has detected the presence of a component additional to its configuration.
Modify the computer configuration using the Configuration command on the diagnostic tools.

88C-26
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-88C000$060.mif
AIRBAGS AND PRETENSIONERS
Fault finding – Interpretation of faults88C
2nd generation
(AC4 phase II)
DF029
PRESENT
OR
STOREDDRIVER'S PRETENSIONER CIRCUITCC: Short circuit
CO: Open circuit
CC.1: Short circuit to 12 volts
CC.0: Short circuit to earth
NOTESNever carry out measuring operations on ignition lines using any tool other than Clip,
NXR or XRBAG.
Use Wiring Diagrams Technical Note for Kangoo VLL.
CO - CC
NOTESNone.
Lock the computer using the command on the diagnostic tool.
Switch off the ignition and check that the driver’s pretensioner ignition module is connected correctly.
Disconnect the passenger pretensioner ignition module and connect a dummy ignition module to the ignition
module connector.
Switch on the ignition and carry out a check using the diagnostic tool.
Replace the driver's pretensioner if the fault is now stored (fault no longer declared as present).
The CLIP, NXR or XRBAG tools must be used for measuring the resistance at point C1 (seat connector) on the
driver's pretensioner line.
If the value obtained is not correct, replace the wiring between points C1 and C3 (seat wiring).

88C-27
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-88C000$060.mif
AIRBAGS AND PRETENSIONERS
Fault finding – Interpretation of faults88C
2nd generation
(AC4 phase II)
DF029
CONTINUED 1
Disconnect the computer connector and fit the B40 30-track adapter.
The CLIP, NXR or XRBAG tool must be used to measure resistance on the cable marked D on the adapter.
If the value obtained is not correct, check the connections of the connector (tracks 1 and 2) and replace the wiring
if necessary.
If the checks carried out have not shown the presence of a fault, check on the base of the airbag computer for the
presence of the 5 shunt opening pins for the 30-track connector.
Check the condition of the computer connections.
Check the condition of the 30-track connector (locking system, etc.).
CC.1 - CC.0
NOTESNone.
Lock the computer using the command on the diagnostic tool.
Disconnect the ignition module of the driver's pretensioner and connect a dummy ignition module to the ignition
module connector.
Switch on the ignition and carry out a check using the diagnostic tool.
If the fault is now stored (fault no longer declared as present), check the condition of the seat wiring.
Replace the driver's pretensioner if the wiring is not faulty.

88C-28
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-88C000$060.mif
AIRBAGS AND PRETENSIONERS
Fault finding – Interpretation of faults88C
2nd generation
(AC4 phase II)
DF029
CONTINUED 2
The CLIP, NXR or XRBAG tool must be used for measuring the insulation appropriate to the type of fault at point
C1 (seat connector) of the driver's pretensioner line.
If the value obtained is not correct, replace the wiring between points C1 and C3 (seat wiring).
Disconnect the computer connector and fit the B40 30-track adapter.
The CLIP, NXR or XRBAG tools must be used for measuring the insulation appropriate to the type of fault on the
cable marked D on the adapter.
If the value obtained is not correct, check the connections of the connector (tracks 1 and 2) and replace the wiring
if necessary.
If the checks carried out have not shown the presence of a fault on the driver's pretensioner circuit, check on the
base of the airbag computer for the presence of the 5 shunt opening pins for the 30-track connector.
Check the condition of the computer connections.
Check the condition of the 30-track connector (locking system, etc.).

88C-29
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-88C000$060.mif
AIRBAGS AND PRETENSIONERS
Fault finding – Interpretation of faults88C
2nd generation
(AC4 phase II)
DF030
PRESENT
OR
STOREDPASSENGER'S PRETENSIONER CIRCUITCC: Short circuit
CO: Open circuit
CC.1: Short circuit to 12 volts
CC.0: Short circuit to earth
NOTESNever carry out measuring operations on ignition lines using any tool other than Clip,
NXR or XRBAG.
Use Wiring Diagrams Technical Note for Kangoo VLL.
CO - CC
NOTESNone.
Lock the computer using the command on the diagnostic tool.
Switch off the ignition and check that the passenger pretensioner ignition module is connected correctly.
Disconnect the passenger pretensioner ignition module and connect a dummy ignition module to the ignition
module connector.
Switch on the ignition and carry out a check using the diagnostic tool.
Replace the passenger's pretensioner if the fault has been stored (fault no longer indicated).
The CLIP, NXR or XRBAG tools must be used for measuring the resistance at point C1 (seat connector) on the
passenger pretensioner line.
If the value obtained is not correct, replace the wiring between points C1 and C3 (seat wiring).

88C-30
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-88C000$060.mif
AIRBAGS AND PRETENSIONERS
Fault finding – Interpretation of faults88C
2nd generation
(AC4 phase II)
DF030
CONTINUED 1
Disconnect the computer connector and fit the B40 30-track adapter.
The CLIP, NXR or XRBAG tool must be used to measure resistance on the cable marked C on the adapter.
If the value obtained is not correct, check the connections of the connector (tracks 3 and 4) and replace the wiring
if necessary.
If the checks carried out have not shown the presence of a fault, check on the base of the airbag computer for the
presence of the 5 shunt opening pins for the 30-track connector.
Check the condition of the computer connections.
Check the condition of the 30-track connector (locking system, etc.).
CC.1 - CC.0
NOTESNone.
Lock the computer using the command on the diagnostic tool.
Disconnect the passenger pretensioner ignition module and connect a dummy ignition module to the ignition
module connector.
Switch on the ignition and carry out a check using the diagnostic tool.
If the fault is now stored (fault no longer declared as present), check the condition of the seat wiring.
Replace the passenger pretensioner if the wiring is not faulty.

88C-31
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-88C000$060.mif
AIRBAGS AND PRETENSIONERS
Fault finding – Interpretation of faults88C
2nd generation
(AC4 phase II)
DF030
CONTINUED 2
The CLIP, NXR or XRBAG tools must be used to measure the insulation appropriate to the type of fault at point
C1 (seat connector) on the passenger pretensioner line.
If the value obtained is not correct, replace the wiring between points C1 and C3 (seat wiring).
Disconnect the computer connector and fit the B40 30-track adapter.
The CLIP, NXR or XRBAG tools must be used for measuring the insulation appropriate to the type of fault on the
cable marked C on the adapter.
If the value obtained is not correct, check the connections of the connector (tracks 3 and 4) and replace the wiring
if necessary.
If the checks carried out have not shown the presence of a fault on the passenger pretensioner circuits, check on
the base of the airbag computer for the presence of the 5 shunt opening pins for the 30-track connector.
Check the condition of the computer connections.
Check the condition of the 30-track connector (locking system, etc.).

88C-32
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-88C000$060.mif
AIRBAGS AND PRETENSIONERS
Fault finding – Interpretation of faults88C
2nd generation
(AC4 phase II)
DF034
PRESENTCOMPUTER LOCKED1.DEF: Locked after impact
2.DEF: Locked with diagnostic tool
NOTESNone.
This fault allows the locked status of the computer to be displayed.
When it occurs, all the trigger lines are inhibited, preventing triggering of the airbags and seat belt pretensioners.
1.DEF
NOTESNone.
This fault is present after the seat belt pretensioners have been triggered with or without triggering of the front
airbags or after the triggering of the side airbags.
Replacement of the computer and the components which operated at the time of impact is compulsory.