fuel consumption RENAULT KANGOO 2013 X61 / 2.G Diesel DCM 1.2 Injection Workshop Manual

13B-24V1 MR-376-X76-13B000$060.mif
DIESEL INJECTION
Fault finding – Fault summary table13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
Tool fault Associated DTC Diagnostic tool name
DF242 0654Engine speed signal output
DF261 0045Turbocharger actuator circuit
DF427 2263Turbocharger actuator control
DF433 0656Fuel consumption signal (ADAC)
DF489 0645Air conditioning compressor control
DF532 2502Alternator charge signal
DF631 0703Brake light switch signal
DF859 0170Injector programming cycle not done
DF886 2269Presence of water in the diesel fuel
DF1083 3264Water in diesel fuel warning light circuit

13B-111
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF433
PRESENT
OR
STOREDFUEL CONSUMPTION SIGNAL (ADAC)
CC.1: Short circuit to + 12 V
CO.0: Open circuit or short circuit to earth
NOTESNone.
Check the connection and condition of the instrument panel connector, component code 247.
Check the connection and condition of the engine management computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connectors, otherwise
replace the wiring.
Check the insulation, continuity and the absence of interference resistance of the following connection:
●47H between components 120 and 247.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If the fault is still present, contact the Techline.
DCM1.2_V08_DF433

13B-175
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP 13 Excessive consumption
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check that the fuel tank is correctly filled and that the appropriate fuel is used.
Apply TEST 13 Diesel fuel conformity check.
Check the levels of engine oil and coolant.Replace the fuel temperature sensor (see MR
388 (Logan/Sandero), MR 423 (Thalia 2/Symbol
2), MR 451 (Duster) or MR 374 (Kangoo VLL),
Mechanical, 13B, Diesel injection, Rail pressure
sensor: Removal - Refitting). Is the fuel temperature sensor leaking?
Check the low pressure circuit by running TEST 1 Low pressure circuit check.
Visually check that there are no leakages on the high pressure circuit by running TEST 7 High pressure circuit
sealing check.
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes
YES
NO
A
DCM1.2_V08_ALP13