weight RENAULT KANGOO ZERO EMISSION 2012 X61 / 2.G Owners Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2012, Model line: KANGOO ZERO EMISSION, Model: RENAULT KANGOO ZERO EMISSION 2012 X61 / 2.GPages: 213, PDF Size: 6.08 MB
Page 37 of 213
partition ................................................. (up to the end of the DU)
1.32
ENG_UD21408_2
Cloison de séparation (X61 - F61 - K61 - Renault)
ENG_NU_911-4_F61e_Renault_1
t o rotate the partition
– Unlock the seat base by moving
handle 1 downwards;
– lift the front passenger seat base
vertically (arrow);
– lower headrest 2 to its lowest setting;
– unlock the seatback by moving
handle 1 downwards again and po -
sition the seatback horizontally. To
make the manoeuvre easier, rotate
the headrest 2 ; –
Pivot the moving section 90 degrees,
lock it at point 5 and lower catch 3.
Note: before refitting the swivelling
section in its original position, check
that locking point 4 is clean.
–
unlock the swivelling section by lift -
ing catch 3;
– reposition the seat base, proceeding
in reverse order.
Swivelling partition
The swivelling section must
always be locked when the
vehicle is driven. Risk of
injury.
SWivelliNg PArtitiON
When moving the swivelling parti -
tion, ensure the seat belt is not dam-
aged. Hold it aside when you rotate
the partition.
1
23
4
5
Maximum weight on the seat in
table position is 80 kg. The weight
must be evenly distributed.
Page 53 of 213
1.48
ENG_UD26558_3
Sécurité enfants : installation du siège enfant (X61 - F61 - R\
enault)
ENG_NU_911-4_F61e_Renault_1
Jaune NoirNoir texte
chilD SAFetY : fitting a child seat (2/5)
child seat attached using the belt
¬ Seat which allows a child seat
with “Universal” approval to be attached
by a seat belt.
² Seat not suitable for fitting child
seats.
³ Check the status of the front
airbag before fitting a child seat or al -
lowing a passenger to use the seat.
(1) Before fitting a child seat: position
the vehicle seat as far back as pos-
sible.
type of seat group
(weight of the child) Seats suitable for fitting a child seat
Front passenger seat (1)
With PASSeNger Air BAg (2) WithOUt
PASSeNger Air BAg
group 0, 0+
(weight below 13 kg) U
U
group i
(weight from 9 kg to 18 kg) U
U
groups ii and iii
(weight from 15 kg to 36 kg) U
U
(2) riSK OF D eAth Or
S eri OUS iNJU rY: Before
installing a child seat on the
front passenger seat, check
that the airbag has been deacti -
vated (refer to “Child safety: front
passenger airbag deactivation and
activation” in Section 1).
2-seat version
Page 55 of 213
1.50
ENG_UD26558_3
Sécurité enfants : installation du siège enfant (X61 - F61 - R\
enault)
ENG_NU_911-4_F61e_Renault_1
Jaune NoirNoir texte
chilD SAFetY : fitting a child seat (4/5)
5-seat version
t ype of child seat Weight of
the child Seat size
ISOFIX Front passenger
seat (1) (2) rear side seats
rear centre seat
carrycot fitted across the
vehicle
Group 0 < 10 kg
F, G XU - IL (3) U (3)
Shell seat/rear-facing seat
Group 0, 0+ and 1 < to 13 kg
a n d 9 t o
18 kg
C, D, E
U - IL (6) U - IL (4)U (4)
Forward-facing seat
Group 1 9 to 18 kg
A, B, B1 XU - IUF - IL (5) U (5)
Booster seat
Group 2 and 3 15 to 25 kg
a n d 2 2 t o
36 kg
X
U (5)U (5)
(1) riSK OF DeA th Or SeriOUS iNJUrY: Before fitting a rear-facing child seat on the front passenger seat, check
that the airbag has been deactivated (refer to the information on “Child safety: front passenger airbag deactivation/
activation” in Section 1).
the table below summarises the information already shown on the diagram on the previous page, to ensure the regula-
tions in force are respected.
Page 132 of 213
rear bench seat..................................... (up to the end of the DU)
rear seats functions ......................................... (up to the end of the DU)
3.21
ENG_UD26786_3
Banquette arrière : fonctionnalité (X61 - F61 - Renault)
ENG_NU_911-4_F61e_Renault_3
Rear bench seat
t o raise the seatback
Before raising the seatback, make sure
there are no objects (water bottle, tool
box etc.) which will prevent it from lock-
ing properly.
Raise the seatback and click it into po-
sition. Check that it is correctly locked.
to fold down the seatback
Before moving the bench seat, make
sure the front seats are pushed forward
enough, that the rear seat belts are un-
fastened and that nothing will obstruct
the manoeuvre.
Lower the rear headrests to storage po-
sition.
Pull lever 1 of the seatback you wish to
fold down (on the right or left-hand side
of the bench seat), and bring the seat-
back down.
reAr BenCH seA t: functions (1/2)
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
When moving the rear
bench seat, make sure
the bench seat anchor -
age points are clean (they
should be free from grit, cloths etc.).
When refitting the seatback,
make sure it is correctly
locked.
If using seat covers, make
sure they do not prevent the seat -
back and seat base latches from
locking in. Ensure that the seat belts
and seat belt fasteners are correctly
positioned.
Reposition the headrests.
Max. weight: 300 kg, evenly distrib-
uted.
1
Page 136 of 213
towingtowing equipment ............................ (up to the end of the DU)
towing equipment fitting ............................................... (up to the end of the DU)
3.25
ENG_UD29274_3
Remorquage : attelage (X61 - F61 - K61 - Renault)
ENG_NU_911-4_F61e_Renault_3
A = 776.5 mm.
Towbar
Permissible nose weight, maxi -
mum permissible towing weight,
braked and unbraked : refer to
Section 6 “Weights”.
Refer to the manufacturer’s instruc-
tions for information on how to fit
and operate the towing equipment.
Please keep these instructions with
the rest of the vehicle documenta -
tion.
t oWBAr
A
If the towbar ball obscures the regis-
tration plate or the rear fog lights, it
should be removed when not in use.
In all cases, comply with local leg -
islation.
Page 140 of 213
JauneNoirNoir texte
4.3
ENG_UD20963_2
Capot moteur (X61 - F61 - Renault)
ENG_NU_911-4_F61e_Renault_4
4
5
3
Closing
Check that nothing has been left in the
engine compartment.
Release the stay and replace it in its
holder 5.
Lower the bonnet and release it when it
is approximately 20 cm from the closed
position. It will latch automatically under
its own weight.
Ensure that the bonnet is
properly locked.
Check that nothing is pre -
venting the catch from lock-
ing (gravel, cloth, etc.).
BOnnet (2/2)
Page 145 of 213
tyre pressure.......................................................... (current page)
tyres ....................................................................... (current page)
tyre pressures ....................................... (up to the end of the DU)
4.8
ENG_UD28661_2
Pressions de gonflage des pneumatiques (en bar) (X61 - F61 - Renault)ENG_NU_911-4_F61e_Renault_4
Tyre pressure
tyRe pRessuRe
a
B : tyre pressures for the front wheels
(non-motorway).
C : tyre pressures for the rear wheels
(non-motorway). D : tyre pressures for the front wheels
(motorway).
E
: tyre pressures for the rear wheels
(motorway).
s pecial note concerning fully laden
vehicles (Maximum Permissible All-Up
Weight) and towing a trailer: the maxi-
mum speed must be limited to 60 mph
(80 km/h) and the tyre pressure in -
creased by 0.2 bar.
Please refer to the information on
“Weights” in Section 6.
t yre safety and use of snow chains:
Refer to the information on “Tyres” in
Section 5 for the servicing conditions
and, depending on the version, the use
of chains.
BC
eD
a
When they need to be replaced, only tyres of the same make, size, type
and profile should be used.
they must: either be identical to those fitted originally or conform
to those recommended by your authorised dealer.
Label A
Open the driver’s door to read it.
Tyre pressures should be checked
when the tyres are cold.
If the tyre pressures cannot be checked
when the tyres are cold, increase the
pressures from 0.2 to 0.3 bar (or 3 psI).
never deflate a hot tyre.
Page 190 of 213
6.1
ENG_UD29097_4
Sommaire 6 (X61 - F61 - Renault)
ENG_NU_911-4_F61e_Renault_6
Section 6: Technical specifications
Vehicle identification plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.2
Engine identification plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3
Engine specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3
Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5
Replacement parts and repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.7
Service sheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.8
Anti-corrosion check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.14
Page 191 of 213
technical specifications ......................... (up to the end of the DU)
vehicle identification ............................. (up to the end of the DU)
paintwork reference .......................................................... (current page)
vehicle identification plates ................... (up to the end of the DU)
6.2
ENG_UD29122_4
Plaques d’identification (X61 - F61 - Renault)
ENG_NU_911-4_F61e_Renault_6
Vehicle identification plates
Vehicle identification plates
a
B
a
t he information shown on the ve -
hicle identification plate should be
quoted on all correspondence or
orders.
Vehicle identification plate A
1 Manufacturer name.
2 EC design number or approval
number.
3 Identification number.
depending on the vehicle, this
information is also given on
marking B.
4 MAM (Maximum Authorised Mass)
for front axle.
5 GTW (Gross train weight: vehicle
fully loaded, with trailer).
6 MPAW (Maximim Permissible
Weight) for front axle.
7 MPAW on rear axle.
8 Reserved for related or additional
entries.
9 Paint reference (colour code).
7
8
96
5
4
3
2
1
Page 193 of 213
weights .................................................................. (current page)
technical specifications .......................................... (current page)
6.4
ENG_UD26560_2
Masses (X61 électrique - Renault)
ENG_NU_911-4_F61e_Renault_6
Weights
Weights (in kg)
the weights indicated are for a basic vehicle without options: they vary depending on the your vehicle’s equipment.
contact an approved dealer.
Maximum permissible all-up weight (MMac)
t otal train weight (MtR) Medium
long
Weights are indicated on the vehicle identification plate (refer to the information on “Vehicle identification plates” in Section 6)
Braked t railer Weight * found by calculating: MtR - MMac
Unbraked trailer weight * 374322
permissible nose weight * 75
Maximum permissible load on roof 100 (including the carrying device)
* t owing weight (t owing a caravan, boat, etc.)
Towing is prohibited when the GTW - MAM calculation is equal to zero, or when the GTW is equal to zero (or is not listed) on the
identification plate.
– It is important to comply with the towing weights, governed by local legislation in each country and, in particular, laid down in
the Road Traffic Regulations. Contact an approved Dealer about any towing equipment.
– When towing, under no circumstances may the total train weight (vehicle + trailer) be exceeded . However the following is
permitted:
– the Maximum permissible weight at the rear may be exceeded by no more than 15%,
– the maximum permissible all-up weight may be exceeded by no more than 10% or 100 kg (whichever occurs first).
In either case, the maximum speed of the towing assembly must not exceed 48 mph (80 km/h) and the tyre pressure must be
increased by 0.2 bar (3 PSI).