engine RENAULT MEGANE HATCHBACK 2016 X95 / 3.G Repair Manual

levels:windscreen washer reservoir ........................... (current page)
windscreen washer ................................................ (current page)
filter air filter ............................................................. (current page)
filter passenger compartment filter .......................... (current page)
filter oil filter ............................................................. (current page)
filter diesel filter ........................................................ (current page)
tanks and reservoirs: windscreen washer .......................................... (current page)
Jaune NoirNoir texte
4.9
ENG_UD18903_5
Niveaux / filtres (X95 - B95 - D95 - Renault)
ENG_NU_837-8_BDK95_Renault_4
windscreen/headlight washer reservoir
Filters
levelS (3/3)FilteRS
Windscreen/headlight washer
reservoir
topping up
W ith the engine switched off, open
cap
1 ,

fill until you can see the fluid,
then refit the cap.
l
iquid
Screen wash product (product with an-
tifreeze in winter).
Jets
Use a tool such as a needle to adjust
the height of the windscreen washer
jets.
nOte
D
epending on the vehicle, to find
out the fluid level, open cap
1

and
pull out the dipstick.
Filters
The replacement of filter elements (air
filter, passenger compartment filter,
diesel filter, etc.) is scheduled in the
maintenance operations for your vehi-
cle.
Replacement intervals for filter el-
ements: refer to the Maintenance
Service Booklet for your vehicle.
1

battery................................................... (up to the end of the DU)
4.11
ENG_UD11753_3
Batterie (X95 - B95 - D95 - Renault)
ENG_NU_837-8_BDK95_Renault_4
The battery 1 does not require any
maintenance.label A
Observe the indications on the battery:
–
2
n
aked flames and smoking forbid-
den;
–
3 eye protection required;
–
4 keep away from children;
–
5 explosive materials;
–
6 refer to the handbook;
–
7 corrosive materials.
Battery
The battery is a specific
type , please ensure it is
replaced with the same
type. Consult an approved
dealer.
Handle the battery with care
as it contains sulphuric acid,
which must not come into
contact with eyes or skin. If
it does, wash the affected area with
plenty of cold water. If necessary,
consult a doctor.
Ensure that naked flames, red hot
objects and sparks do not come into
contact with the battery as there is a
risk of explosion.
BAtte Ry
Depending on the vehicle, a system
continuously checks the battery charge
status. If the level drops, the message
“Battery low start engine” is displayed
on the instrument panel. In this case,
start the engine. Then the message
“Battery charging” appears on the in-
strument panel for the duration of the
charging time.
The charge status of your battery can
decrease especially if you use your ve-
hicle:
–

for short journeys;
–


for driving in town;
–


when the temperature drops;
–


a
fter extended use of consumers
(radio etc.) with the engine switched
off.
Replacing the battery
As this operation is complex, we advise
you to contact an approved Dealer.
1
The engine may be hot
during operations in close
proximity. In addition, the
engine cooling fan may
start at any moment.
Risk of injury.
A234
567

maintenance:bodywork ........................................ (up to the end of the DU)
washing ................................................ (up to the end of the DU)
paintwork maintenance ................................... (up to the end of the DU)
anti-corrosion protection ....................... (up to the end of the DU)
cleaning: outside the vehicle .......................... (up to the end of the DU)
4.12
ENG_UD22865_9
Entretien de la carrosserie (X45 - H45 - J77 - X81 - X85 - B85 - C85 - \
S85 - X91 - B91 - K91 - D91 - X83 - X61 - X77 ph2 - K85 - X95 - B95 - D9\
5 - K95 - J95 - R95 - L38 -
ENG_NU_837-8_BDK95_Renault_4
Jaune NoirNoir texte
Bodywork maintenance
BODyWORk MAintenAnCe (1/2)
– Allow rust to form following minor im-
pacts.
–

U
se solvents not approved by our
Technical Department to remove
stains as this could damage the
paintwork.
–

D
rive frequently in snow or muddy
conditions without washing the ve-
hicle, particularly under the wheel
arches and body.
–
mino
r impacts
You should take a minimum number of
precautions in order to safeguard your
vehicle against such risks and not to
lose the benefit of your vehicle’s anti-
corrosion protection.
What you should not do
– Degrease or clean mechanical com-
ponents (e.g. the engine compart-
ment), underneath the body, parts
with hinges (e.g. inside the fuel tank
flap) and painted plastic external
fittings (e.g. bumpers) using high-
pressure cleaning equipment or by
spraying on products not approved
by our Technical Department. If ade-
quate precautions are not taken, this
could give rise to corrosion or opera-
tional faults.
–

W
ash the vehicle in bright sunlight or
freezing temperatures.
–

S
crape off mud or dirt without
prewetting.
–

Allow
dirt to accumulate.
A well-maintained vehicle will last
longer. It is therefore recommended to
maintain the exterior of the vehicle reg-
ularly.
protection against the effects
of corrosive agents
Although your vehicle has been treated
with very effective anti-corrosion prod-
ucts, it nevertheless remains subject to
the effects of:
–

corrosives in the atmosphere
–


a
tmospheric pollution (built-up
and industrial areas),
–

s
aline atmospheres (near the
sea, particularly in hot weather),
–

seasonal
and damp climatic con-
ditions, (e.g.: road salt in winter,
water from road cleaners, etc.).
–

abrasives
W

ind-borne dust and sand, mud,
road grit thrown up by other vehi-
cles, etc.

JauneNoirNoir texte
4.13
ENG_UD22865_9
Entretien de la carrosserie (X45 - H45 - J77 - X81 - X85 - B85 - C85 - \
S85 - X91 - B91 - K91 - D91 - X83 - X61 - X77 ph2 - K85 - X95 - B95 - D9\
5 - K95 - J95 - R95 - L38 -
ENG_NU_837-8_BDK95_Renault_4
– Before going through a roller type car
wash, return the windscreen wiper
stalk to the Park position (refer to
the information on the “Windscreen
wash/wipe” in Section 1). Check the
mounting of external accessories,
additional lights and mirrors, and
ensure that the wiper blades are se-
cured with adhesive tape.
Remove the radio aerial mast if your
vehicle is fitted with this equipment.
Remember to remove the tape and
refit the antenna after washing.
–

S
pray mechanical components,
hinges, etc. with products approved
by our Technical Department to
protect them after they have been
cleaned.
BODyWORk MAintenAnCe (2/2)
We have selected special products
to care for your vehicle and you can
obtain these from the manufactur-
er’s accessory outlets.
you should
– Observe the vehicle stopping dis- tances when driving on gravelled
surfaces to prevent paint damage.
–

R
epair, or have repaired quickly,
areas where the paint has been
damaged, to prevent corrosion
spreading.
–

R
emember to visit the body shop
periodically if your vehicle has an
anti-corrosion warranty. Refer to the
Maintenance Service Booklet.
–

R
espect local regulations about
washing vehicles (e.g. do not wash
your vehicle on a public highway). –

W
ash your car frequently,
with the
engine off , with cleaning products
recommended by our Technical
Department (never use abrasive
products) and be sure to jet-rinse off:
–

s
pots of tree resin and industrial
grime;
–

b
ird droppings, which cause a
chemical reaction with the paint
that rapidly discolours paint-
work and may even cause the
paint to peel off;



W
ash the vehicle immediately to
remove these marks since it is im-
possible to remove them by pol-
ishing;
–

s
alt, particularly in the wheel
arches and underneath the body
after driving in areas where the
roads have been gritted;
–

mud
in the wheel arches and un-
derneath the body which forms
damp patches.

5.4
ENG_UD21559_4
Kit de gonflage (X95 - B95 - D95 - L38 - X38 - X32 - B32 - Renault)
ENG_NU_837-8_BDK95_Renault_5
Jaune NoirNoir texte
Depending on the vehicle, remove the
central partition in the storage compart-
ment to access the inflation kit.
Open the kit, remove caps
1 and 3 (the
cap must not be removed from the
bottle) then screw bottle
2 to its base 3.
wi

th the engine running and the
parking brake applied,
–

unscrew
the valve cap on the wheel
concerned and screw inflation
adapter
6 onto the valve;
–

connect
adapter
8
to the accessories
socket on the dashboard of the vehi-
cle;
–

p
ress switch
5

to inflate the tyre to
the recommended pressure (check
the label affixed to the edge of the
driver’s door);
–

after
a maximum of 5 minutes, stop
inflating and read the pressure (on
pressure gauge

4
);
no

te: while the bottle is emptying
(approximately 30 seconds), pres-
sure gauge
4

will briefly indicate a
pressure of 6 bar, then the pressure
will drop.
tyre Pressure KIt (2/3)
143
5
6
78
2– adjust the pressure: to increase it, continue inflating with the kit, to
reduce it, turn button
7

located on
the inflation adapter.
If a minimum pressure of 1.8 bar is
not reached after 15 minutes, repair
is not possible; do not drive the ve-
hicle but contact an approved dealer.
Depending on the vehicle, in the event
of a puncture, use the kit located under-
neath the luggage compartment carpet.
Before using this kit, park
the vehicle at a sufficient
distance from traffic, switch
on the hazard warning
lights, apply the handbrake, ask all
passengers to leave the vehicle and
keep them away from traffic.
If the vehicle is parked on
the hard shoulder, you must
warn other road users of
your vehicle’s presence
with a warning triangle or with other
devices as per the legislation apply-
ing to the country you are in.

JauneNoirNoir texte
5.13
ENG_UD22105_3
Projecteurs avant : remplacement des lampes (X95 - B95 - D95 - Renault)\
ENG_NU_837-8_BDK95_Renault_5
The engine may be hot
when carrying out opera-
tions in close proximity. In
addition, the engine cooling
fan can come on at any moment.
Risk of injury.
The bulbs are under pres-
sure and can break when
replaced.
Risk of injury.
To comply with current legislation,
or as a precaution, you can obtain
an emergency kit from an approved
dealer containing a set of spare
bulbs and fuses.
heaDlIghts: changing bulbs (2/2)
main beam headlight
Remove the cover E , press the bulb
holder 5 downwards to unlock it.
Bulb type:
h 7.
BcDe3245B6
Front side light
Remove the cover E and pull the bulb
holder 6 .
Bulb type:
w 5 w
.

5.24
ENG_UD23613_2
Fusibles (X95 - B95 - D95 - K95 - Renault)
ENG_NU_837-8_BDK95_Renault_5
Fuses (2/2)
Some accessories are protected by
fuses located in the engine compart-
ment in fuse box
C.
However, because of their reduced ac-
cessibility, we advise you to have your
fuses replaced by an approved Dealer.allocation of fuses(the presence of certain fuses depends
on the vehicle equipment level)
1 Electronic parking brake;
2 Brake lights;
3 Automatic door locking;
4 Driver’s electric window;
5 Passenger compartment unit;
6 Direction indicator lights;
7 Navigation system; 8 Interior rear-view mirror;
9 Rear screen wiper;
10 and
11 Rear electric windows;
12 ABS/ESP;
13 Passenger electric window;
14 Windscreen washer;
15 Heated door mirrors;
16 Radio;
17 Luggage compartment accessories
socket;
18 Rear seat accessories socket;
19 Cigarette lighter.
c
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19

batterytroubleshooting ............................... (up to the end of the DU)
5.25
ENG_UD9611_2
Batterie : dépannage (X95 - B95 - D95 - Renault)
ENG_NU_837-8_BDK95_Renault_5
Battery
Battery: troubleshooting (1/2)
to avoid all risk of sparks:
– Ensure that any electrical consumers
(courtesy lights, etc.) are switched
off before disconnecting or recon-
necting the battery.
–

W
hen charging, stop the charger
before connecting or disconnecting
the battery.
–

D
o not place metal objects on the
battery to avoid creating a short cir-
cuit between the terminals.
–

Always
wait at least one minute after
the engine has been switched off
before disconnecting a battery.
–

M
ake sure that you reconnect the
battery terminals after refitting.
connecting a battery charger
the battery charger must be com-
patible with a battery with nominal
voltage of 12 volts.
Do not disconnect the battery when the
engine is running. Follow the instruc-
tions given by the manufacturer of
the battery charger you are using.
Special procedures may be
required to charge some
batteries. Contact your ap-
proved dealer.
Avoid all risk of sparks which may
cause an immediate explosion, and
charge the battery in a well-venti-
lated area. Risk of serious injury.
Handle the battery with care
as it contains sulphuric acid,
which must not come into
contact with eyes or skin. If
it does, wash the affected area with
plenty of cold water. If necessary,
consult a doctor.
Ensure that naked flames, red hot
objects and sparks do not come into
contact with the battery as there is a
risk of explosion.
The engine may be hot when car-
rying out operations in close prox-
imity. In addition, the engine cooling
fan can come on at any moment.
Risk of injury.

5.26
ENG_UD9611_2
Batterie : dépannage (X95 - B95 - D95 - Renault)
ENG_NU_837-8_BDK95_Renault_5
Attach positive lead A to mounting 1
attached to (+) terminal 2
then to
(+)
t

erminal
3

of the battery supplying
the current.
Attach the negative lead
B

to the
(–
) t

erminal
4

of the battery supplying
the current, then to the (–) terminal
5


of the discharged battery.
Start the engine. As soon as it is run-
ning, disconnect leads
A

and
B

in the
reverse order (
5 - 4 - 3 - 2 ).
starting the vehicle using the
battery from another vehicle
If you have to use the battery from an-
other vehicle to start, obtain suitable
jump leads (with a large cross section)
from an approved dealer or, if you al-
ready have jump leads, ensure that
they are in perfect condition.
t

he two batteries must have an iden-
tical nominal voltage of 12 volts. The
battery supplying the current should
have a capacity (amp-hours, Ah) which
is at least the same as that of the dis-
charged battery.
Ensure that there is no risk of contact
between the two vehicles (risk of short
circuiting when the positive terminals
are connected) and that the discharged
battery is properly connected. Switch
off your vehicle ignition.
Start the engine of the vehicle supply-
ing the current and run it at an interme-
diate engine speed.
Battery: troubleshooting (2/2)
2
3
4
5
a
B
1
Check that there is no con-
tact between leads A and B
and that the positive lead
A
is not touching any metal
parts on the vehicle supplying the
current.
Risk of injury and/or damage to the
vehicle.
2
5

wiper blades ......................................... (up to the end of the DU)
wipers blades ............................................. (up to the end of the DU)
5.30
ENG_UD21380_4
Balais d’essuie-vitres (X95 - B95 - D95 - L38 - X38 - X32 - B32 - Re\
nault)
ENG_NU_837-8_BDK95_Renault_5
Wipers (replacing blades)
wInDscreen wIPer BlaDes
replacing windscreen wiper
blades 1
with the ignition on and engine
switched off, lower the windscreen
wiper stalk completely: they stop
slightly away from the bonnet.
Lift wiper arm
3 ,

pull tab
2

(move-
ment
A) and push the blade upwards.
to refit
S

lide the blade along the arm until it
clips on. Make sure that the blade is
correctly locked in position. Return the
windscreen wiper stalk to the park po-
sition.
1
2
3
Check the condition of the wiper
blades. You are responsible for their
service life:
–

clean
the blades, windscreen and
rear screen regularly with soapy
water;
–

do
not use them when the wind-
screen or rear screen are dry;
–

free
them from the windscreen or
rear screen when they have not
been used for a long time.
rear screen wiper blade 4
– Lift wiper arm 6;
–
pivot
blade
4
until some resistance is
met (movement
C);
–

d
epending on the vehicle, press
tab
5, then remove the blade by pull-
ing it (movement
B).
to refit
T

o refit the wiper blade, proceed in re-
verse order to removal. Make sure that
the blade is correctly locked in position.
4
5
B
c
a
6
– In frosty weather, make
sure that the wiper blades
are not stuck by ice (to
avoid the risk of the motor
overheating).
–

Check
the condition of the wiper
blades.
Replace the wiper blades as soon
as they begin to lose efficiency
(approximately once a year).
Whilst changing the blade, take care
not to drop the arm onto the window
after it has been removed as this
may break the window.