wheel bolts RENAULT MEGANE HATCHBACK 2016 X95 / 3.G Owners Manual

tool kit ................................................... (up to the end of the DU)
hubcap tool ........................................... (up to the end of the DU)
jack ....................................................... (up to the end of the DU)
puncture................................................ (up to the end of the DU)
wheelbrace ........................................... (up to the end of the DU)
trims ...................................................... (up to the end of the DU)
emergency spare wheel ....................... (up to the end of the DU)
wheelbrace ............................................................ (current page)
5.6
ENG_UD18915_3
Bloc-outils (X95 - B95 - D95 - Renault)
ENG_NU_837-8_BDK95_Renault_5
Tool kit (jack, wheelbrace, etc.)
Hubcap
tOO l KI t / wheel tr I m – wheel
The tool kit is located in the luggage
compartment: lift the carpet.
The tools included in the tool kit depend
on the vehicle.
wheelbrace 1
Jack 2
When replacing the jack, fold it cor-
rectly and position the wheelbrace cor-
rectly before replacing it in its position.
h

ubcap tool
3
T

his tool is used to remove the wheel
trims.
w

heel bolt guide
4
T

o finish loosening or starting to tighten
the wheel bolts.
towing hitch


5
Refer

to the information on “Towing” in
Section 5.
Do not leave the tools unsecured inside the vehicle as they may come
loose under braking. After use, check that all the tools are correctly
clipped into the tool kit, then position it correctly in its housing: there is a
risk of injury.
If wheel bolts are supplied in the tool kit, only use these bolts for the emergency
spare wheel: refer to the label affixed to the emergency spare wheel.
The jack is designed for wheel changing purposes only. Under no circumstances
should it be used for carrying out repairs underneath the vehicle or to gain access
to the underside of the vehicle.
2
1
3
5
wheel trim
Remove it using the hubcap tool 3 by
connecting the hook in the recess pro-
vided next to the valve
6 (to attach the
metal clip).
To refit wheel trim, align it with valve
6.
Push the retaining hooks in fully, start-
ing with side
B near the valve, followed
by
C and D, finishing at E opposite the
valve.
no

te: if you are using anti-theft bolts,
refer to the information on “Changing a
wheel”.
6
B
cD
e
4

changing a wheel.................................. (up to the end of the DU)
puncture................................................ (up to the end of the DU)
lifting the vehiclechanging a wheel ............................ (up to the end of the DU)
5.7
ENG_UD18916_4
Changement de roue (X95 - B95 - D95 - Renault)
ENG_NU_837-8_BDK95_Renault_5
Offer up the jack 4 horizontally; the jack
h ead must be lined up with jacking
point
1 located on the underside of the
sill, closest to the wheel concerned, as
shown by arrow

2
.
Start cranking the jack up by hand to
align the base plate (which should be
pushed slightly under the vehicle).
Turn the wheelbrace until the wheel lifts
off the ground.
Changing a wheel
Switch on the hazard warn-
ing lights.
Keep the vehicle away from
traffic and on a level sur-
face where it will not slip (if neces-
sary, place a solid support under the
jack base).
Apply the parking brake and engage
a gear (first or reverse, or P for auto-
matic transmissions).
Ask all the passengers to leave the
vehicle and keep them away from
traffic.
3
1
2
4
changIng a wheel (1/2)
To prevent any risk of injury
or damage to the vehicle,
only crank the jack until the
wheel you are replacing is
a maximum of 3 centimetres off the
ground.
If the vehicle is parked on
the hard shoulder, you must
warn other road users of
your vehicle’s presence
with a warning triangle or with other
devices as per the legislation apply-
ing to the country you are in.
Vehicles equipped with a jack
and wheelbrace
If necessary, remove the wheel trim.
Use the wheelbrace

3
to slacken off the
wheel bolts. Position it so as to be able
to push from above.
If the vehicle is not equipped with a
jack or wheelbrace, you can obtain
these from your approved dealer.

5.8
ENG_UD18916_4
Changement de roue (X95 - B95 - D95 - Renault)
ENG_NU_837-8_BDK95_Renault_5
Undo the bolts and take off the wheel.
Fit the emergency spare wheel onto
the hub and rotate it until the mounting
holes in the wheel coincide with those
of the hub.
If bolts are supplied with the emergency
spare wheel, only use these bolts for
the emergency spare wheel. Tighten
the bolts, checking that the wheel is
correctly positioned on its hub and
lower the jack.
With the wheel on the ground, tighten
the bolts fully and have the tightness
of the bolts checked (tightening torque:
110 N.m) and the emergency spare
wheel pressure checked as soon as
possible.
changIng a wheel (2/2)
anti-theft bolt
I f you use anti-theft bolts, fit these
nearest the valve (wheel trim may
not be able to fit).
If you have a puncture, re-
place the wheel as soon as
possible.
A tyre which has been punc-
tured should always be inspected
(and repaired, where possible) by a
specialist.