RENAULT MEGANE SCENIC 1995 Service Repair Manual

LOWER STRUCTURE
Front towing ring mounting reinforcement
41Front towing ring mounting reinforcement
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the front end cross
member.
For standardisation purposes, the cross member is
delivered by the Parts Department without a
reinforcement.
It will be necessary to screw the towing ring bracket to
the cross member to position the reinforcement.
In the operation described below, only descriptions of
the joints specific to the part concerned are given.
The information on the additional parts will be dealt
with in their appropriate chapters (see contents).
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part delivered alone
PARTS CONCERNED (thickness in mm):
1
2
3Front end cross member reinforcement
Front end cross member
Front end cross member closure panel 2.5
1.5
1.2
41-10
V

LOWER STRUCTURE
Front towing ring mounting reinforcement
41
41-11
641V1-17954
V

LOWER STRUCTURE
Rear towing ring bracket
41PRear towing ring bracket
INTRODUCTION
The replacement of this part is a basic operation for a
right hand rear collision.
The rear towing ring bracket is bolted to the right hand
rear side member and to the lower section of the end
panel.
This may help with positioning when replacing the rear
end panel.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Assembled part with threaded roller.REMOVAL OF THE REAR TOWING RING
BRACKET
Remove:
– the two mounting bolts (A) passing through the side
member and their reinforcement,
– the mounting bolt (B) on the lower section of the end
panel.
PRF4115
41-12
W

LOWER STRUCTURE
Bearing rear mounting support
41SBearing rear mounting support
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the centre floor.
For standardisation purposes, the floor is delivered by
the Parts Department without the bearing rear
mounting support.
It will be necessary to fit the support after fitting the
centre floor.
The repair bench must be used.
In the operation described below, only descriptions of
the joints specific to the part concerned are given.
The information on the additional parts will be dealt
with in their appropriate chapters (see contents).
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part delivered alone.
PARTS CONCERNED (thickness in mm):
PRF4116
1
2
3
4Bearing rear mounting support
Sleeve stop
Tunnel stiffener
Centre floor1
1.5
1
1
41-13
X

LOWER STRUCTURE
Bearing rear mounting support
41P
41-14
641Y1-17627-1
X

LOWER STRUCTURE
Bearing front mounting support
41PBearing front mounting support
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the centre floor.
For standardisation purposes, the floor is delivered by
the Parts Department without the bearing front
mounting support.
It will be necessary to fit the support after fitting the
centre floor.
The repair bench must be used.
In the operation described below, only descriptions of
the joints specific to the part concerned are given.
The information on the additional parts will be dealt
with in their appropriate chapters (see contents).
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part delivered alone.
PARTS CONCERNED (thickness in mm):
PRF4117
1
2Bearing front mounting support
Front cross member under the front seat1
1.5
644X1-17896-1
41-15
Y

LOWER STRUCTURE
Acceleration sensor mounting
41SAcceleration sensor mounting
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the centre floor.
For standardisation purposes, the centre floor is
delivered by the Parts Department without the
acceleration sensor mounting.
In the operation described below, only descriptions of
the joints specific to the part concerned are given.
The information on the additional parts will be dealt
with in their appropriate chapters (see contents).
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part delivered alone.
PARTS CONCERNED (thickness in mm):
1
2
3
4
5Acceleration sensor mounting
Front seat height adjuster
Front seat height adjuster reinforcement
Centre floor
Tunnel stiffener 1.2
1.5
1.5
1
1
41-16
Z

LOWER STRUCTURE
Acceleration sensor mounting
41P
41-17
X1 = 122 mm
Z

LOWER STRUCTURE
Central floor rear reinforcement
41Central floor rear reinforcement
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the centre floor or the
cross member.
For standardisation purposes, these parts are
delivered by the Parts Department without the rear
floor reinforcement.
In the operation described below, only descriptions of
the joints specific to the part concerned are given.
The information on the additional parts will be dealt
with in their appropriate chapters (see contents).
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part delivered alone.
PARTS CONCERNED (thickness in mm):
PRF4119
1
2
3
4
5Central floor rear reinforcement
Sill panel closure panel component
Cross member
Rear side member
Centre floor 1.5
1.8
1.2
1.5
1
641Z1-17951
41-18
AA

LOWER STRUCTURE
Central floor rear reinforcement
41
41-19
AA