RENAULT MEGANE SCENIC 1995 Service Repair Manual
Manufacturer: RENAULT, Model Year: 1995, Model line: MEGANE SCENIC, Model: RENAULT MEGANE SCENIC 1995Pages: 2492, PDF Size: 32.28 MB
Page 1 of 2492
77 11 176 201APRIL 1995Edition Anglaise
General
"The repair methods given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The methods may be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories
from which his vehicles are constructed."All copyrights reserved by the Regie Nationale des Usines Renault.
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of the
Regie Nationale des Usines Renault.
Régie Nationale des Usines Renault S.A. 1995
SPECIFICATIONS
LIFTING
TOWING
LUBRICANTS CONSUMABLES
DRAINING, RE-FILLING
BA0A - BA0E - BA0F - BA0G - BA0L - BA0U
C
VALUES AND SETTINGS
Page 2 of 2492
SECTION VIEW
Page 3 of 2492
TOWING
All types
Contents
SPECIFICATIONS
Engine - Clutch - Gearbox
Vehicle identification01-1
01-2
LIFTING
Trolley jack - Axle stands
Vehicle liftsPage01
02
03
General
02-1
02-2
03-1
LUBRICANTS - CONSUMABLES
Packaging 04-1
DRAINING, RE-FILLING
Engine
Gearbox
Power assisted steering
04
05
05-1
05-3
05-4
VALUES AND SETTINGS
Dimensions
Capacity - Grades
Belt tension
Accessories belt tension
Timing belt tension
Tightening the cylinder head
Dimensions of the main braking
components
Values for checking the front axle
geometry
Values for checking the rear axle
geometry
Underbody heights
Brake limiter
07
07-1
07-2
07-5
07-7
07-13
07-15
07-17
07-18
07-21
07-22
07-23
Page 4 of 2492
SPECIFICATIONS
Engine- Clutch - Gearbox
01
Vehicle typeEngine
Type CapacityClutch typeType of manual gearbox and
automatic transmission
BA0E E7J 1390180 DST 3050
180 CP 3300JB1
BA0F
BA0LK7M 1598 200 HR 4000 JB1
BA0G F3R 1998 215 HRN 4000 JB3
BA0A
BA0UF8Q 1870200 HRV 4600
200 HRV 3100JB1
BA0F K7M 1598 - AD4
VEHICLE IDENTIFICATION
Example : BA0E
B : Body type (example 5 door hatchback)
A : Project code (example 64)
0E : Engine suffix (example E7J 764)
01-1
Page 5 of 2492
SPECIFICATIONS
Vehicle identification
• near to the emergency spare wheel (B) with a
duplicate label of the oval plate on the lower
section of the passenger door (C).
01
LOCATION OF THE VEHICLE IDENTIFICATION
PLATE
Two possible locations on the vehicle:
• in the engine compartment (A),
98485-1R
98517R
98516R
01-2
Page 6 of 2492
SPECIFICATIONS
Vehicle identification
01
REGIE NATIONALE DES
USINES RENAULT S.A.
e000-00/00000-0000-00
VF0000000
00000000
0000 kg
0000 kg
1
- 0000 kg
2
- 0000 kg
10 0 0 0 0
0 0 0 0 0 0 0 0
0 0 0 0 0 0 011 0 0 0 0 0 0 0 0
7
13
8
14
9
12
Renault
1
2
3
4
5
6
VF0000000
00000000
0000
00 000 000
00 000 000
0000000
9
10
12 11 1
2
8
7
14
13
B A
01-3
Page 7 of 2492
SPECIFICATIONS
Vehicle identification
01
It shows:
At A : the name of the manufacturer,
At B : the E.E.C. approval number
At 1 : the type mines of the vehicle preceded by the world manufacturers identification code (VF1 corre-
sponds to RENAULT FRANCE),
At 2 : the chassis number,
At 3 : the maximum permissible weight,
At 4 : the maximum permitted total train weight,
At 5 : the maximum permitted weight on the front axle,
At 6 : the maximum permitted weight on the rear axle,
At 7 : the first figure indicates the gearbox or factory options,
the second figure indicates the equipment level,
At 8 : the vehicle type,
At 9 : the technical equipment code,
At 10 : additional factory optional equipment,
At 11 : the equipment level,
At 12 : the paint code,
At 13 : a letter describing the factory of manufacture followed by the fabrication number,
At 14 : the trim code.
NOTE : Depending on the country of export, certain details might not be given. The plate described above
shows all possible information.
ALLOCATION OF TECHNICAL EQUIPMENT CODES
The equipment code, the three letters which appear in (9), must be documented for vehicle identification
reasons (ordering spare parts, warranty claim, etc.)
01-4
Page 8 of 2492
LIFTING
Trolley jack - Axle stands
AXLE STANDS
When putting the vehicle on axle stands, they
must be positioned:
- either under the reinforcements designed for
lifting the vehicle using the vehicle’s jack,
- or under the points located behind the
reinforcements.
Axle stands are positioned at the rear when the
vehicle is lifted from the side.
02
98699R
Safety symbol (special precautions to be taken when carrying out operations).
SPECIAL TOOLING REQUIRED
Cha. 280 -02 Adaptable cross piece for trolley
jack
Cha. 408 -01
or Adaptable socket for trolley jack
Cha. 408 -02
If a trolley jack is used, appropriate axle
stands must always be used.
It is forbidden to lift the vehicle by supporting its
weight under the front suspension arm or under
the V shaped part of the rear axle.
Depending on the type of trolley jack, use sockets
Cha. 408-01 or Cha. 408-02 to position the cross
piece Cha. 280-02.
To lift the front or rear, support the vehicle’s
weight under the vehicle’s jacking points .
TROLLEY JACK USED FROM THE SIDE
Use cross piece Cha. 280-02.
Take the weight under the sill, level with the front
door.
Position the flange correctly in the groove of the
cross piece.
98336G85679-1G7
02-1
Page 9 of 2492
LIFTING
Vehicle lifts
02
SAFETY INSTRUCTIONS
Several scenarios should be considered:
1 - WHEN REMOVING COMPONENTS
In general, never use a 2 post lift, if a four post lift
can be used.
If this is not possible, position the lifting pads
under the body sill, level with the vehicle’s jacking
points.2 - SPECIAL CASE - REMOVING AND REFITTING
THE ENGINE AND TRANSMISSION ASSEMBLY
In this special case, the body of the vehicle must
be firmly attached to the arms of the two post lift
using the special pads.
FOG
Reference FOG 449 8111 - 449 8411
or
CHEMICO
Reference 39 2550 0001
or
SCHENCH
Reference 776 684
98703S
FRONT
98704S
REAR
These must be positioned in line with the vehicle’s
jacking points. They must be clipped into the
holes in the body sill.
02-2
Page 10 of 2492
TOWING
All types
FRONT
03
OBSERVE THE LEGAL TOWING REQUIREMENTS OF THE COUNTRY YOU ARE IN.
NEVER USE THE DRIVESHAFTS FOR TOWING THE VEHICLE.
The towing points may only be used for towing the vehicle on the road. They should never be used for remo-
ving the vehicle from a ditch or for any other similar breakdown operation or to lift the vehicle, either direct-
ly or indirectly.
98705S
REAR
98702S
03-1