ESP RENAULT MEGANE SCENIC 1995 Service Owner's Manual

LOWER STRUCTURE
Rear end pillar lower reinforcement
PRE4109
41E
INTRODUCTION
The replacement of this part is a complementary
operation to the rear end cross member.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Part assembled with welded nuts.
PARTS CONCERNED (thickness in mm) :
1Rear end pillar lower reinforcement 1
2Rear end cross member 0.8
3Body side lining 0.7
4Rear end pillar lining 1
5Rear floor 0.7
6Rear side member 1.2
7Lights mounting 0.7
8Rear end pillar lining 1
41-8

LOWER STRUCTURE
Rear end cross member assembly
PRE4110
41F
INTRODUCTION
The replacement of this part is a complementary
operation to the rear end panel.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Part assembled with:
- striker plate reinforcement,
- central reinforcement.
PARTS CONCERNED (thickness in mm) :
1Rear end cross member 0.8
2Rear end pillar lower reinforcement 1
3Rear floor base 0.8
4Rear floor 0.7
5Tailgate striker plate central
reinforcement 1.2
6Rear floor central reinforcement 0.8
41-11

LOWER STRUCTURE
Rear floor unit
PRE4111
41G
INTRODUCTION
The replacement of this part is identical to the me-
thod described in the basic manual (M.R. 313 -
Section 41). Only the joints at the rear end pillar
lower reinforcements are different, which are des-
cribed in this document (section 41-E).
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Part assembled with:
- side member assemblies,
- floor assembly,
- cross member under the floor,
- floor base assembly,
- rear end cross member assembly,
- rear end pillar reinforcement.
41-14

UPPER SIDE STRUCTURE
Top of body
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the roof for a
front side impact.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page) and MR 313 for the front
section.
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Part assembled with welded pin.
43A
PRE4310
PARTS CONCERNED (thickness in mm) :
1Body side 0.77
2Rear quarter panel lining 0.7
3Rear pillar upper reinforcement 1
4Rear pillar lower reinforcement 1
5Stretcher lining 1.2
6Centre pillar reinforcement 1.5
7Rear corner reinforcement 1.2
8Rear end pillar lining 1
9Rear upper side drip moulding 1or
43-1

UPPER REAR STRUCTURE
Rear wing panel
INTRODUCTION
This part may be replaced in two ways:
• by part section as a basic operation for a rear
side impact (see diagram),
• completely, as a complementary operation to
the roof.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Part assembled with:
- striker plate reinforcement,
- pin to be welded 3 x2.9,
- soundproofing,
- bumper mounting reinforcement assembly.
PRE4415
44A
or
PARTS CONCERNED (thickness in mm) :
1Wing panel 0.8
2Rear quarter panel lining 0.7
3Sill panel closure panel 1.5
4Rear pillar reinforcement 1
5Rear outer wheel arch 0.7
6Rear upper side drip moulding 1
7Lights moulding 0.7
8Rear end pillar lining 1
9Rear end panel 1
10Rear end pillar lower reinforcement 1
44-1

UPPER REAR STRUCTURE
Rear lights mounting
PRE4416
44B
INTRODUCTION
The replacement of this part is a complementary
operation to the wing panel.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Single part.
PARTS CONCERNED (thickness in mm) :
1Lights mounting 0.7
2Rear upper side drip moulding 1
3Rear end pillar lining 1
4Rear end panel 1
254b01-15380
A
CAA11536-2R7
12
44-10

UPPER REAR STRUCTURE
Upper side drip moulding
44C
INTRODUCTION
The replacement of this part is a complementary
operation to the rear wing panel.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Part assembled with:
- balancer ball joint,
- parcel shelf mounting.
PARTS CONCERNED (thickness in mm) :
1Rear upper side drip moulding 1
2Lights mounting 0.7
3Rear end pillar lining 1
4Rear end pillar lower reinforcement 1
PRE4423
44-12

UPPER REAR STRUCTURE
Rear pillar reinforcement
PRE4417
44D
INTRODUCTION
The replacement of this part is a complementary
operation to the rear wing panel for a rear side
impact.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Part assembled with:
- upper pillar reinforcement,
- mounting nuts,
- lower pillar reinforcement,
- acoustic plug.
NOTE : for this operation the upper part of the
reinforcement must be unpicked on the new part.
PARTS CONCERNED (thickness in mm) :
1Rear pillar lower reinforcement 1
2Rear pillar upper reinforcement 1
3Rear quarter panel lining 0.7
4Rear outer wheel arch 0.7
5Rear inner wheel arch 0.8
6Sill panel closure panel 1.5
7Seat belt mounting reinforcement 1.5
8Stretcher lining 1.2
44-15

UPPER REAR STRUCTURE
Rear quarter panel lining assembly
PRE4419
44F
INTRODUCTION
The replacement of this part is a complementary
operation to a complete wing panel.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Part assembled with:
- outer wheel arch,
- seat mounting reinforcement,
- connecting bracket,
- rear end pillar lining assembly,
- upper corner reinforcement assembly.
PARTS CONCERNED (thickness in mm) :
1Body side lining 0.7
2Rear quarter panel lining 0.7
3Centre pillar lining 1.2
4Front sill closure panel 1.5
5Rear sill closure panel 0.8
6Rear inner wheel arch 0.8
7Seat belt mounting reinforcement 1.5
8Stretcher lining 1.2
9Rear floor base 0.8
10Rear floor 0.7
11Rear end pillar lining 1
12Rear end pillar lower reinforcement 1
or
NOTE : to avoid replacing the part located behind
the sill panel, cut the front lower section of the li-
ning, see section (C) in the diagram below.
44-21

UPPER REAR STRUCTURE
Outer wheel arch
PRE4421
44G
INTRODUCTION
This part can be replaced in two ways:
• by part section A , complementary to the rear
end pillar,
• by part section B , complementary to the wing
panel.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Part assembled with:
- outer wheel arch,
- seat mounting reinforcement,
- connecting bracket,
- rear end pillar lining assembly,
- upper corner reinforcement assembly.
PRE4420
SECTION A : complementary to rear end pillar
reinforcement.
SECTION B : complementary to rear wing panel.
PARTS CONCERNED (thickness in mm) :
1Body side lining 0.7
2Rear quarter panel lining 0.7
3Rear end pillar lining 1
4Rear floor base 0.8
5Rear floor 0.7
6Rear inner wheel arch 0.8
7Seat belt mounting reinforcement 1.5or
44-27