height RENAULT MEGANE SCENIC 1995 Service Repair Manual

TOWING
All types
Contents
SPECIFICATIONS
Engine - Clutch - Gearbox
Vehicle identification01-1
01-2
LIFTING
Trolley jack - Axle stands
Vehicle liftsPage01
02
03
General
02-1
02-2
03-1
LUBRICANTS - CONSUMABLES
Packaging 04-1
DRAINING, RE-FILLING
Engine
Gearbox
Power assisted steering
04
05
05-1
05-3
05-4
VALUES AND SETTINGS
Dimensions
Capacity - Grades
Belt tension
Accessories belt tension
Timing belt tension
Tightening the cylinder head
Dimensions of the main braking
components
Values for checking the front axle
geometry
Values for checking the rear axle
geometry
Underbody heights
Brake limiter
07
07-1
07-2
07-5
07-7
07-13
07-15
07-17
07-18
07-21
07-22
07-23

VALUES AND SETTINGS
Underbody heights
07
Axle type Tubular axle 4 bar axle
Vehicle type
BA0A - BA0E - BA0F - BA0L - BA0UBA0G
Wheel diameter (inches) 13" 14"
H1 - H2 (mm) 121 ± 5 123.5 ± 5
H4 - H5 (mm) 44.5 ± 11 52 ± 11
07-22

FUEL TANK
Gauge
19
For petrol engines, the pump and gauge sender
unit are an inseparable assembly.
For diesel engines, there is no pump submerged in
the fuel tank, there is only a gauge sender unit.
For removing the gauge sender unit refer to the
section FUEL TANK "Pump - sender unit".
Checking the gauge sender unit
Ensure the resistance varies by moving the float.
DisplayValue between terminals
A1 and B1 (in Ω)
4/4 7 maximum
3/4 54.5 ± 7
1/2 98 ± 10
1/4 155 ± 16
Minimum 300 ± 20
Display Height H (in mm)
4/4 48
3/4 90
1/2 133
1/4 147
Minimum 190
Measuring the height H
With the gauge sender unit removed, place it on a
flat surface.
H is the height measured between the float pin
and the working surface.
NOTE : these value are given for information only.
19-25

30
GENERAL
Uderbody heights / Consumables

33
REAR AXLE
Underbody heights for tubular rear axle

33
REAR AXLE
Underbody heights for four bar rear axle

33
REAR AXLE
Underbody heights for four bar rear axle

33
REAR AXLE
Underbody heights for four bar rear axle

33
REAR AXLE
Underbody heights for four bar rear axle

GLAZING
Front door window
Fit the window flush with the fixed window pillar
seal (C).
The height of the window is adjusted by moving
the stop (7) of the window mechanism toothed
wheel.
54
Tighten the upper pillar bolt (6).
Open the door and tighten the lower pillar
mounting (6).
Position the fixed window fully in the pillar
groove.
Fit the window flush with the pillar seal (A) and
with a protrusion (B = 1 mm) with the exterior
mirror seal.Tighten the mounting bolts (5).
Tightening torque of all mounting bolts 8 N.m.
MM M M
OO O O
VV V V
AA A A
BB B B
LL L L
EE E E

WW W W
II I I
NN N N
DD D D
OO O O
WW W W
12281-1R1
12281-1R2
12277-2R
12469R
54-3