instrument panel RENAULT MEGANE SCENIC 1995 Service Repair Manual

DIESEL EQUIPMENT
Pre-post-heating unit
13
DIAGRAM KEY
104Ignition switch
163Starter
171Air conditioning clutch
206Air conditioning trifunction pressure switch
247Instrument panel
251Bi-function coolant temperature switch
257Pre-heating unit
398EGR solenoid valve
412Fast idle solenoid valve (AC version)
597Engine fuse box
642AC / pre-heating separation diode
645Passenger compartment fuse box
680Pre-heating unit n° 1
681Pre-heating unit n° 2
682Pre-heating unit n° 3
683Pre-heating unit n° 4
711Diesel fuel pump
741Altimetric capsule
743Altimetric relay
777Power feed for fuse boxConnector (A)
+ Bat+ before ignition feed
Connector (B)
1Feed to heater plugs 1 and 3
2Feed to heater plugs 2 and 4
Connector (C)
A1 / S2Load dependence solenoid valve
control
A2 / PCLoad lever microswitch information
A3 / CTNCTN type sensor coolant temperature
information
B1/+APC+ after ignition feed
B2 / DEMStarter information
B3 / TemPre-heating warning light control (via
earth)
C1 / S1Not used
C2 / -Bat Earth
C3 / ClimFast idle solenoid valve control during
post-heating phase
92206-2R
IDENTIFICATION OF CONNECTORS
13-30

DIESEL EQUIPMENT
Pre-post-heating unit
13
FAULT FINDING
1. The pre-heating warning light does not operate
TEST SOLUTION
Earth the warning light output of connector (C) using
a 2 A fuse when the ignition is turned on (track B3).
• The fuse blows.
• The warning light does not illuminate.
• The warning light does illuminate.The warning light wiring in the instrument panel is in
short circuit. Repair the wiring.
The bulb is blown or the wiring is faulty.
Replace the bulb or repair the wiring.
Check:
- + battery on connector (A),
- + after ignition on connector (C),
- battery earth on connector (C).
If the feed is correct, replace the pre-post-heating
unit.
2. The pre-heating warning light only operates for a fraction of a second when the ignition is turned on.
TEST SOLUTION
Disconnect connector (B) and test the pre-heating:
• The warning light illuminates and there is a
voltage at the connector outputs (B).
• The warning light illuminates and there is no
voltage at the connector outputs (B).
• The pre-heating warning light illuminates for a
fraction of a second only.Check the plugs circuit. If it is correct, check and
replace the faulty plug(s).
Replace the pre-post-heating unit.
Check the before ignition feed to the pre-heating
unit.
13-33

STARTING - CHARGING
Alternator
16
OPERATION - FAULT FINDING
These vehicles are fitted with alternators with in-
ternal ventilation, an integral regulator and a
warning light on the instrument panel which ope-
rates as follows :
- when the ignition is turned on, the warning
light illuminates,
- when the engine starts, the warning light ex-
tinguishes,
- if the warning light illuminates again when
the engine is running, there is a "charging"
fault.
LOOKING FOR FAULTS
The warning light does not illuminate when the
ignition is turned on.
Check:
- the electrical connections are correct,
- the bulb is not blown (to do this, earth the cir-
cuit; the bulb should illuminate).
The warning light illuminates when the engine is
running
There is a charging fault which could be due to:
- the alternator drive belt being broken or the
charging cable being cut,
- internal damage to the alternator (rotor, sta-
tor, diodes or brushes),
- regulator fault,
- an excess voltage.The customer complains of a charging fault and
the warning light operates correctly.
If the regulated voltage is less than 13.5 V, check
the alternator. The fault could be caused by:
- a destroyed diode,
- a cut phase,
- track contamination or wear.
Checking the voltage
Connect a voltmeter across the battery terminals
and read the battery voltage.
Start the engine and increase the engine speed
until the voltmeter needle stabilises at the
regulated voltage.
This voltage should be between 13.5 V and 14.8 V.
Connect as many consumers as possible, the
regulated voltage should remains between 13.5 V
and 14.8 V.
IMPORTANT: if arc welding is carried out on the
vehicle, the battery and the regulator must be
disconnected.
16-2

INJECTION
General
17
K7M engine
SPECIAL NOTES FOR MULTIPOINT INJECTION
•55 track SIEMENS FENIX 5 computer.
•Semi-sequential multipoint injection. Injectors controlled in pairs (injectors for cylinders 1 and 4 then
injectors for cylinders 2 and 3).
•Static ignition with two coils.
•Canister bleed solenoid controlled by RCO signal.
•EGR solenoid valve controlled by RCO signal (K7M 703).
•Idle speed correction depending on:
- air conditioning,
- heated windscreen,
- power assisted steering pressostat.
•Injection warning light on instrument panel operational.
•Use fault finding fiche N° 27.
FITTING A 2ND GENERATION ENGINE IMMOBILISER REQUIRES A SPECIAL PROCEDURE FOR REPLACING THE
COMPUTER.
17-8

INJECTION
General
17
F3R engine
SPECIAL NOTES FOR MULTIPOINT INJECTION
•55 track SIEMENS FENIX 5 computer.
•Injection cylinder by cylinder (sequential).
•Static ignition with two coils.
•Canister bleed solenoid controlled by RCO signal.
•Idle speed correction depending on:
- battery voltage,
- air conditioning,
- heated windscreen.
•Injection warning light on instrument panel operational.
•Use fault finding fiche N° 27.
•Computer configuration depending on gearbox type (manual gearbox or automatic transmission).
FITTING A 2ND GENERATION ENGINE IMMOBILISER REQUIRES A SPECIAL PROCEDURE FOR REPLACING THE
COMPUTER.
17-10

INJECTION
Injection fault warning light
17
PRINCIPLE FOR ILLUMINATION OF THE INJECTION FAULT WARNING LIGHT ON THE INSTRUMENT PANEL
• Vehicle without engine immobiliser system
When the ignition is turned on, the warning light illuminates for 3 seconds then extinguishes.
• Vehicle with engine immobiliser system deactivated
When the ignition is turned on, the warning light illuminates for 3 seconds then extinguishes.
When the doors are unlocked, the red immobiliser warning light, which was previously flashing, extin-
guishes. When the ignition is turned on, it illuminates for 3 seconds then extinguishes.
• Vehicle with engine immobiliser system activated
When the ignition is turned on, the computer does not identify the code and the vehicle cannot be star-
ted. The injection warning light illuminates for 3 seconds then extinguishes.
Before the ignition is turned on, the red immobiliser warning light flashes. When the ignition is turned
on, this light flashes twice as fast.
If a fault in the immobiliser system is detected when the engine is running, the injection warning light
will flash in the engine speed range from idle speed to 1 500 rpm approximately.
• Fault with an injection system component
Faults in the following components cause the warning light to illuminate:
- absolute pressure sensor,
- throttle position potentiometer,
- injectors,
- idle speed regulation stepping motor (K7M engine),
- idle speed regulation valve (F3R engine),
- no vehicle speed information when the vehicle is moving,
- EGR solenoid valve (K7M 703 engine),
- automatic transmission computer → injection computer (F3R - K7M engines).
17-24

INJECTION
Operating wiring diagram
17
KEY TO OPERATIONAL WIRING DIAGRAMS (E7J, F3R, K7M)
COMPONENT NO DESCRIPTION
109
119
120
146
147
149
193 to 196
218
222
224
225
228
236
238
242
244
247
250
272
310
319
341
371
398
437
565
597
645
649
663
664
679
746
772
777
927
MF
MHOn board computer
Automatic transmission computer
Injection computer
Pinking sensor (located under the inlet manifold for E7J engine)
Absolute pressure sensor
TDC sensor
Injectors
Fuel pump
Throttle position potentiometer
Power assisted steering pressostat
Diagnostic socket
Idle speed regulation micromotor
Fuel pump relay (in engine fuse box)
Injection feed locking relay
Oxygen sensor
Coolant temperature sensor
Instrument panel
Vehicle speed sensor
Air temperature sensor
Ignition power module
Air conditioning control panel
Idle speed regulation solenoid valve
Fuel vapour recirculation solenoid valve
Exhaust gas recirculation solenoid valve (EGR)
Throttle body heater (under throttle body)
Throttle body assembly
Engine fuse box
Passenger compartment connection unit
Idle speed regulation stepping motor
Dual ignition coil n°1 (cylinders 1 and 4)
Dual ignition coil n° 2 (cylinders 2 and 3)
Radio anti-interference condenser
Cylinder reference sensor
Heater relay (in engine fuse box)
Power fuse board (near battery)
Inertia switch
Rear right hand electrical earth
Engine electrical earth (located on the cylinder block between the starter and the al-
ternator for the E7J engine)
17-39

INJECTION
Operating wiring diagram
17
E7J engine
COMPUTER TRACK ALLOCATION
TrackALLOCATION
1Power earth
2Electronic earth
3Vehicle speed information
4+ before ignition (permanent) computer memory
5Canister bleed signal (sequential earth period)
6Pump relay control (via track N° 2)
7Locking relay control (via track N° 2)
8Diagnostic line for erasing the memory and power assisted steering pressostat information
9Throttle position potentiometer information (pin N° 4 on 222)
10Heater relay command
11TDC sensor signal (track B)
12Rev counter information at instrument panel
13Connection with injection fault warning light on instrument panel
14Air temperature information
15Coolant temperature information
16+ 5 V feed for absolute pressure sensor and throttle potentiometer
17Common earth for absolute pressure sensor, throttle potentiometer and coolant temperature
sensor
18Emission of diagnostic signal to diagnostic socket
19Main computer feed via injection locking relay
20Air conditioning compressor command
21Injector control via earth
22Not used
23+ or - feed to idle speed micromotor (pin N° 1)
24+ or - feed to idle speed micromotor (pin N° 2)
17-41

INJECTION
Operating wiring diagram
17
TrackALLOCATION
25Not used
26Not used
27Not used
28Command for coil for cylinders 1 and 4
29Command for coil for cylinders 2 and 3
30Command for injector n° 1 and n° 4 via earth (n° 1 flywheel end)
31Pinking sensor screened cable
32+12 V before ignition
33TDC sensor signal (track B)
34TDC sensor signal (track A)
35Stepping motor command (0 - 12 V)
36Stepping motor command (0 - 12 V)
37Immobiliser coded line input
38Uni-directional diagnostic line L for entry into diagnostic mode only
(looking for computer)
39Not used
40Stepping motor command (0 - 12 V)
41Throttle angle information for automatic transmission computer
42RCO control (sequential earth period for canister bleed solenoid valve RCO)
43Command for injection fault warning light on instrument panel
44Common earth for pinking sensor and coolant temperature sensor and absolute pressure sensor
45+ 5 V feed for absolute pressure sensor and throttle position potentiometer
46Common earth for air temperature sensor and throttle position potentiometer
47Not used
48Command (via earth) for fuel pump relay and engine speed information
49Not used
K7M engine
17-45

INJECTION
Operating wiring diagram
17
TrackALLOCATION
25Command for injector n° 2 via earth
26Command for injection fault warning light on instrument panel
27Not used
28Command for coil for cylinders 1 and 4
29Command for coil for cylinders 2 and 3
30Command for injector n° 4 via earth (timing end)
31Pinking sensor screened cable
32+12 V before ignition
33TDC sensor signal (track B)
34TDC sensor signal (track A)
35Immobiliser coded line input
36Not used
37Not used
38Uni-directional diagnostic line L for entry into diagnostic mode only
(looking for computer)
39Not used
40Not used
41Throttle angle information for automatic transmission computer
42Cylinder reference sensor information
43Engine speed information
44Common earth for pinking sensor and coolant temperature sensor and absolute pressure sensor
45+ 5 V feed for absolute pressure sensor and throttle position potentiometer
46Common earth for air temperature sensor and throttle position potentiometer
47Not used
48Command (via earth) for fuel pump relay (236)
49Not used
F3R engine
17-49