jacking RENAULT MEGANE SCENIC 1995 Service Repair Manual

LIFTING
Trolley jack - Axle stands
AXLE STANDS
When putting the vehicle on axle stands, they
must be positioned:
- either under the reinforcements designed for
lifting the vehicle using the vehicle’s jack,
- or under the points located behind the
reinforcements.
Axle stands are positioned at the rear when the
vehicle is lifted from the side.
02
98699R
Safety symbol (special precautions to be taken when carrying out operations).
SPECIAL TOOLING REQUIRED
Cha. 280 -02 Adaptable cross piece for trolley
jack
Cha. 408 -01
or Adaptable socket for trolley jack
Cha. 408 -02
If a trolley jack is used, appropriate axle
stands must always be used.
It is forbidden to lift the vehicle by supporting its
weight under the front suspension arm or under
the V shaped part of the rear axle.
Depending on the type of trolley jack, use sockets
Cha. 408-01 or Cha. 408-02 to position the cross
piece Cha. 280-02.
To lift the front or rear, support the vehicle’s
weight under the vehicle’s jacking points .
TROLLEY JACK USED FROM THE SIDE
Use cross piece Cha. 280-02.
Take the weight under the sill, level with the front
door.
Position the flange correctly in the groove of the
cross piece.
98336G85679-1G7
02-1

LIFTING
Vehicle lifts
02
SAFETY INSTRUCTIONS
Several scenarios should be considered:
1 - WHEN REMOVING COMPONENTS
In general, never use a 2 post lift, if a four post lift
can be used.
If this is not possible, position the lifting pads
under the body sill, level with the vehicle’s jacking
points.2 - SPECIAL CASE - REMOVING AND REFITTING
THE ENGINE AND TRANSMISSION ASSEMBLY
In this special case, the body of the vehicle must
be firmly attached to the arms of the two post lift
using the special pads.
FOG
Reference FOG 449 8111 - 449 8411
or
CHEMICO
Reference 39 2550 0001
or
SCHENCH
Reference 776 684
98703S
FRONT
98704S
REAR
These must be positioned in line with the vehicle’s
jacking points. They must be clipped into the
holes in the body sill.
02-2

Contents
GENERAL
Opening clearances
Description of parts
Sub-frame dimensions
Central floor
Main bodywork dimensions40-1
40-3
40-5
40-6
40-7
LOWER STRUCTURE
41-1
41-2
41-3
41-4 Pages40
41
Bodywork
AFront jacking pad
BSill panel stiffener
CRear seat belt mounting
strengthener
DExtreme rear crossmember
UPPER SIDE STRUCTURE
43
43-1
43-3
43-5
43-8
43-9
43-10
43-12
43-15
43-17
43-19 AWindscreen frame
BFrame upright trim
C"A" post assembly
D"A" post trim strengthener
E"A" post trim (scuttle side)
F"B" post strengthener
G"B" post trim with rear section of sill
panel
H"B" post trim only
IWing panel upper front trim
assembly
JPartial sill panelUPPER REAR STRUCTURE
44
44-1
44-2
44-7
44-10
44-11
44-18
44-21
44-23
44-27
44-31
44-35
44-37
44-39
44-41 AHydraulic pump bracket
BRear wing panel
CLights bracket
DWing panel closing device
ERight-hand wing panel trim
FWing panel trim
GRear lights bracket strengthener
HWing panel drip moulding
IRear end panel assembly
JInterior right-hand wheel arch
KUpper rear floor extender
LLower rear floor extender
MRear side member extender
NHood compartment rear partition
assembly
OPENINGS OTHER THAN SIDE DOORS48
48-1
48-2Boot
Hood cover

GENERAL
Description of parts
40
PRS4043
1 Windscreen frame
2 Hood cover lid (composite)
3 Rear end panel assembly
4 Lights bracket
5 Rear wing panel
6 Sill panel
7 "A" post assembly
8 Front jacking pad
40-3

LOWER STRUCTURE
Front jacking pad
II I I
NN N N
TT T T
RR R R
OO O O
DD D D
UU U U
CC C C
TT T T
II I I
OO O O
NN N N
The changing of this part is an additional opera-
tion to the changing of the front side crossmem-
ber.
CC C C
OO O O
MM M M
PP P P
OO O O
SS S S
II I I
TT T T
II I I
OO O O
NN N N

OO O O
FF F F

TT T T
HH H H
EE E E

RR R R
EE E E
PP P P
LL L L
AA A A
CC C C
EE E E
MM M M
EE E E
NN N N
TT T T

PP P P
AA A A
RR R R
TT T T
Part only.
41A
PRE4101
CC C C
OO O O
NN N N
NN N N
EE E E
CC C C
TT T T
II I I
OO O O
NN N N

TT T T
OO O O

TT T T
HH H H
EE E E

FF F F
RR R R
OO O O
NN N N
TT T T

SS S S
II I I
DD D D
EE E E
CC C C
RR R R
OO O O
SS S S
SS S S
MM M M
EE E E
MM M M
BB B B
EE E E
RR R R1
Thickness of the panels concerned (mm)
Front jacking pad 2.5
Side crossmember 1
Unpicking
3 MAG weld seams
30 mm long
Welding
11994
41-1