oil filter RENAULT MEGANE SCENIC 1995 Service Repair Manual

API SG 5W30
API SH 5W30API SG 10W40
API SH 10W40 API SG 15W40
API SH 15W40
VALUES AND SETTINGS
Capacity - Grades
07
Components
After
draining
3,5
5,5
(plus 0.5 litres
for the oil
filter)E.E.C. countries
Other countries Capacity
in litres
Grade
Petrol engine
(oil)
E7J
K7M
F3R
0°C
+30°C-30°C
+10°C+20 °C-20°C-10°C
-15°C
CCMC-G5 10W30 - 10W40 -
10W50
CCMC-G5 5W40 - 5W50
CCMC-G5 5W30
CCMC-G4 15W40 - 15W50
API SG 10W30
API SH 10W30
0°C
+30°C-30°C+10°C+20 °C -20°C-10°C
-15°C
07-2

VALUES AND SETTINGS
Capacity - Grades
07
Components
After
draining
5
(plus 0.5 litres
for the oil
filter)E.E.C. countries
Other countries Capacity
in litres
Grade
Diesel engine
(oil)
F8Q
0°C
+30°C-30°C+10°C+20 °C-20°C-10°C
-15°C+15°C
CCMC-PD2 15W40
CCMC-PD2 10W40
API CD 10W30
0°C
+30°C-30°C+10°C+20 °C-20°C-10°C
-15°C+15°C
API CD 15W40
API CD 10W40
07-3

Contents
Consumables
Identification
Oil consumption
Oil pressure
Engine - Gearbox
Engine and transmission assembly
Sump10-1
10-1
10-2
10-3
10-4
10-19
10-43
TOP AND FRONT OF ENGINE
Timing belt
Cylinder head gasketPage Page
11
Engine and
peripherals
11-1
11-12 ENGINE AND PERIPHERALS
10FUEL SUPPLY - PUMPS -
PREHEATING
Fuel supply
Fuel cut-out on impact
Fuel gallery
Injectors
Fuel filter
Pump flow
Supply pressure
Diesel equipment
Specifications
Description of the pump
Tightening torques (in daN.m)
Special notes
Idle speed settings
Microswitches
Pump
Pump - timing
Coded solenoid valve
Operating diagram
Pre-post-heating unit
Injector holder - heater plug
Fuel filter
Coolant temperature sensor
Inlet - exhaust manifolds
Pump
Brake assistance vacuum pump
Mechanical power assisted steering
pump13-1
13-3
13-8
13-9
13-10
13-11
13-15
13-16
13-17
13-18
13-20
13-22
13-23
13-27
13-28
13-29
13-30
13-36
13-37
13-39
13-40
13-41
13-4213
FUEL MIXTURE
Specifications
Throttle body
Inlet manifold
Exhaust manifold
Manifolds12-1
12-7
12-15
12-18
12-2012

ENGINE AND PERIPHERALS
Engine - Gearbox
10
F8Q engine
- the air inlet sleeve, the air filter and its
mounting,
- the cooling assembly (see section 19
"Radiator"),
- the alternator belt (see section 16
"Alternator").
Disconnect the compressor feed wire (if fitted).
Remove:
- the compressor mounting bolts (if fitted) and
secure it to the front cross member,
- the power assisted steering pump pulley,
- the oil filter,
- the power assisted steering pump mounting
bolts as well as the power assisted steering
pipe bracket bolt.
Move the pump away and secure it to the sub-
frame.
Disconnect:
- the heating hoses on the thermostat
mounting,
98904R1
- the preheating unit (secure it to the engine),
- the accelerator and clutch cables,
- the altimetric sensor corrector,
- the relay plate and the engine connection unit
electrical connector,
- the fuel supply pipe on the diesel filter using
tool Mot. 1311-06,
98756R
99461R
- the connector on the diesel filter. - the brake servo pipe,
- the pipes and connectors on the fast idle and
EGR solenoid valves,
10-15

ENGINES AND PERIPHERALS
Engine and transmission assembly
10
E7J Engine
SPECIAL TOOLING
Mot. 1040-01 Dummy cradle for removing and
refitting the engine and
transmission assembly
Mot. 1202 Hose clip pliers
Front sub-frame mounting bolt 6
Rear sub-frame mounting bolt 11
Upper shock absorber cup mounting bolt 3
Wheel bolts 9
Brake caliper mounting bolt 3.5
Universal steering joint mounting bolt 3.5
TIGHTENING TORQUES (in daN.m)
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect:
- the battery,
- the relay plate and the engine connection unit
electrical connector,
98756R
- the connectors of the ignition module and the
HT coil wire,
- the oxygen sensor connector,
- the accelerator and clutch cables.
Drain:
- the cooling circuit,
- the engine if necessary,
- the gearbox (by removing the cover) if
necessary.
Remove:
- the earth strap,
- the air filter,
- the nut and the eccentric bolt (1) (remove
using a roll pin punch) from the steering shaft
yoke after having pushed the protector back.
97390-1R
10-19

ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F8Q engine
- the pipes and connectors for the fast idle and
EGR solenoid valves,
- the brake servo pipe,
- the accelerator and clutch cables,
- the diesel fuel filter connector,
- the compressor feed wire (if fitted).
Remove:
- the cooling assembly (see section 19
"Radiator"),
- the alternator belt (see section 16),
- the compressor mounting bolts (if fitted) and
attach it to the front cross member.
NOTE: cut the base of tool Mot. 1159 to 30 mm.
99023R2
99024R2
Remove the oil filter.
Unclip the alternator wiring and move it to one
side.
Diagram for drilling tool Mot. 1159. (For
instructions on use, refer to page 10-40).
99028R
Fit tool Mot. 1159.
10-39

TOP AND FRONT OF ENGINE
Cylinder head gasket
11 F3R ENGINE
Remove:
- the timing belt (see section 11-Timing belt),
- the spark plug caps.
98899R
98900S
Disconnect:
- the pinking sensor,
- the cylinder reference sensor,
- the absolute pressure sensor and its pipe,
- the idle speed valve,
- the air and coolant sensors,
- the throttle potentiometer,
- the injectors,
- the canister solenoid valve pipe,
- the oil vapour rebreathing pipe,
- the brake servo pipe,
- the accelerator cable,
- the fuel supply and return pipes (gallery end),
- the coolant temperature sensor (9).
Remove:
- the air filter,
- hoses 3, 4, 5, 6, 7, 8,
99222R
11-17

TOP AND FRONT OF ENGINE
Cylinder head gasket
11F8Q ENGINE
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect the battery.
Remove the engine undertray.
Drain the cooling circuit via the lower radiator
hose (radiator end).
SPECIAL TOOLING REQUIRED
TIGHTENING TORQUES (in daN.m)
Wheel bolt 9
Crankshaft pulley bolt 12
Suspended engine mounting cover bolt 6
Suspended engine mounting limiter bolt 4
Tensioner nut 5
EQUIPMENT REQUIRED
Star socket ST X 14 FACOM for example
Star socket EX 255 FACOM for example
Engine support tool DESVIL M300 for example
99174R
Mot. 251-01 Dial gauge mounting
Mot. 252-01 Pressure plate for measuring cylinder liner protrusion
Mot. 1311-06 Tool for removing fuel pipe
Mot. 591-02 Index
Mot. 591-04 Angular wrench for tightening the cylinder head
Mot. 1054
TDC pin
Mot. 1159 Tool for retaining the engine on the sub-frame
Mot. 1202 Hose clip pliers
Mot. 1273 Tool for checking belt tension
Mot. 1281-01 Oil filter wrench
Mot. 1289-03 Fork for centring suspended engine mounting limiter
Remove:
- the timing belt (see section 11 - timing belt),
- bolts (A) mounting the tensioner, together
with bolt (B) for the alternator drive belt ten-
sion strut mounting,
11-22

TOP AND FRONT OF ENGINE
Cylinder head gasket
11F8Q ENGINE
- the exhaust flange at the manifold outlet,
- the air filter,
- the earth strap,
- the fuel return union on the injection pump,
together with the mounting bracket on the
manifold,
- the mounting bolts for the inner timing cover
on the engine block.
95658-4R
Remove the oil filter.
Release the wiring from the alternator and move
the wiring to one side. Fit tool Mot. 1159 under the oil pump.
Note : cut the base of tool Mot. 1159 to 30 mm.
99023R2
99024R2
11-23

TOP AND FRONT OF ENGINE
Cylinder head gasket
11F8Q ENGINE
99028R
Diagram for drilling tool Mot. 1159 (diameter 10.5
mm).
Fit the bracket of tool Mot. 1159 under the water
pump.
99310R
98904S
Disconnect:
- the thermostat hoses,
- the connectors for the sensors,- the brake servo pipe,
- the 2 oil vapour rebreathing hoses on the decan-
ter,
- the accelerator cable,
- the preheater plug connector,
- the injection pump connectors,
- the solenoid valve pipes,
- the fuel supply pipe to the diesel fuel filter using
tool Mot. 1311-06
99461R
Remove the cylinder head bolts using the star
socket 55 toolEX 255
FACOM for example.
11-24