AUX RENAULT PULSE 2012 1.G Owner's Guide


> (GLW    0RGHO .$2(0B5HQDXOW @
.make a call via voice dialling by pushing thebutton \for more than 2 seconds then say
the voice tag clearly.
\bANDS-FREE TELEP\bONE OPERATION
(Type B)
JV\b0519X
Buttons:
1. Phone button
2. A-Z button
3. TUNE/MENU/ENTER dial
4. SETUP button
Microphone:
The microphone is located near the map light.
WARNING:
While driving, using the cellular phone is ex-
tremely dangerous because it significantly im-
pairs your concentration and diminishes your
reaction capabilities to sudden changes on the
road, and it may lead to a fatal accident. This
applies to all phone call situations such as when
receiving an incoming call, during a phone
conversation, when calling through the phone
book search, etc.
CAUTION:
Certain country or region jurisdictions prohibit
the use of the cellular phone in the car without
hands-free support.
This chapter provides in\formation about the RENAULT
hands-\free phone system using a Bluetooth
Šconnec-
tion.
Bluetooth
Šis a wireless radio communication stan-
dard. This system o\f\fers a hands-\free \feature \for your
cellular phone to enhance driving com\fort.
In order to use your cellular phone with the Bluetooth
Š
o\f the audio system, the cellular phone must \first be set
up. Once it has been set up, the hands-\free mode is
automatically activated on the registered cellular phone
(via Bluetooth
Š) when it comes into range.
A noti\fication message appears on the audio display
when the phone is connected, when an incoming call
is being received, as well as when a call is initiated.
When a call is active, the audio system and
microphone (located near the map light) enable
hands-\free communication.
I\f the audio system is in use at the time, the radio, CD,
or AUX source mode will be muted and will stay muted
until the active call has ended.
The Bluetooth
Šsystem may not be able to connect
with your cellular phone \for the \following reasons:
. The cellular phone is too \far away \from the vehicle.
. The Bluetooth
Šmode on the cellular phone has
not been activated.
. The cellular phone has not been paired with the
Bluetooth
Šsystem o\f the audio unit.
. The cellular phone does not support BluetoothŠ
technology (BT Core v1.2, \bands Free Pro\file v1.0
and Object Push Pro\file v1.0) . NOTE:
For details, see the cellular phone’s owner’s
manual.
\bands-\free phone setup
To set up the BluetoothŠsystem to pair with (connect
or register) a pre\ferred cellular phone, push the
button, select the BluetoothŠkey, and then push the
TUNE/MENU/ENTER dial. It is also possible to display
the set up menu directly by pushing the
button.
. Pair Device
Bluetooth
Šcellular phones can be paired with the
system. A maximum o\f 5 cellular phones can be
registered.
. Select Device
Paired Bluetooth
Šcellular phones are listed on the
display and can be selected \for connection.
. Delete Device
A registered Bluetooth
Šcellular phone can be
deleted.
. Bluetooth
I\f this setting is turned o\f\f, the connection between
the Bluetooth
Šdevices and the in-vehicle Blue-
toothŠmodule will be cancelled.
When success\fully paired, a noti\fication message will
be displayed. During the connection the \following
status icons will be displayed (top le\ft o\f display):
Signal strength (
) , Battery status () and
BluetoothŠ().
*: I\f the low battery message comes on, the BluetoothŠ
device must be recharged soon.
Heater and air conditioner, and audio system4-63
&RQGLWLRQ