ECO mode RENAULT PULSE 2012 1.G Workshop Manual


> (GLW    0RGHO .$2(0B5HQDXOW @
5-14Starting and driving
JVS0014XRight-Hand Drive (RHD) modelTo release the shi\ft lock, \ber\form the \following
\brocedure
1. Models with Intelligent KEY system: Place theignition switch in the “OFF” or “LOCK” \bosition.
Models without Intelligent KEY system: Place the
ignition switch in the “LOCK” \bosition and remove
the key.
2. A\b\bly the \barking brake.
3. De\bress the shi\ft lock release button.
4. Push and hold the selector lever button and move the selector lever to the “N” (Neutral) \bosition
while holding down the shi\ft lock release button.
5. Place the ignition switch to the “ON” \bosition to release the steering wheel lock.
The vehicle may be moved, by \bushing, to the desired
location.
I\f the selector lever cannot be moved out o\f the “P”
(Park) \bosition, have a RENAULT dealer check the AT
system as soon as \bossible.
Fail-sa\fe
When the \fail-sa\fe o\beration occurs, the AT will be
locked in third gear.
If the vehicle is driven under extreme conditions,
such as excessive wheel spinning and subse-
quent hard braking, the fail-safe system may be
activated. This will occur even if all electrical
circuits are functioning properly. In this case,
turn the ignition switch off and wait for 3
seconds. Then turn the ignition switch back to
the “ON” position. The vehicle should return to
its normal operating condition. If it does not
return to its normal operating condition, have a
RENAULT dealer check the transmission and
repair it if necessary.
DRIVING WITH CONTINUOUSLY VARI-
ABLE TRANSMISSION (CVT)
The Continuously Variable Transmission (CVT) in your
vehicle is electronically controlled to \broduce maximum
\bower and smooth o\beration.
The recommended o\berating \brocedures \for this
transmission are shown on the \following \bages. Follow
these \brocedures \for maximum vehicle \ber\formance
and driving enjoyment.
WARNING:
Do not downshift abruptly on slippery roads.
This may cause a loss of control.
CAUTION:
. The cold engine idle speed is high, so use
caution when shifting the transmission into
a forward or reverse position before the
engine has warmed up. .
Avoid revving up the engine while the
vehicle is stopped. This could cause unex-
pected vehicle movement.
. Never shift to either the “P” (Park) or “R”
(Reverse) position while the vehicle is mov-
ing. This could cause serious damage to the
transmission.
. Start the engine in either the “P” (Park) or
“N” (Neutral) position. The engine will not
start in any other position. If it does, have
your vehicle checked by a RENAULT dealer.
. Shift into the “P” (Park) position and apply
the parking brake when at a standstill for
longer than a short waiting period.
. Keep the engine at idling speed while
shifting from the “N” (Neutral) position to
any driving position.
. When stopping the vehicle on an uphill
grade, do not hold the vehicle by depressing
the accelerator pedal. The foot brake pedal
should be depressed in this situation.
Starting vehicle
1. A\fter starting the engine, \fully de\bress the \foot
brake \bedal be\fore moving the selector lever out
o\f the “P” (Park) \bosition.
2. Kee\b the \foot brake \bedal de\bressed and move the selector lever to a driving \bosition.
3. Release the \barking brake, the \foot brake \bedal, and then gradually start the vehicle in motion.
The CVT is designed so the foot brake pedal
MUST be depressed before shifting from the “P”
(Park) position to any driving position while the
ignition switch is in the “ON”position.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-16Starting and driving
P (Park):
Use this position when the vehicle is par\fed or when
starting the engine.Make sure that the vehicle is
completely stopped and move the selector lever
into the \bP”(Park) position. Apply the par\fing
bra\fe. When par\fing on a hill, first depress the foot
bra\fe pedal, apply the par\fing bra\fe, and then move
the selector lever into the \bP” (Par\f) position.
R (Reverse):
Use this position to bac\f up. Ma\fe sure that the vehicle
is completely stopped before selecting the \bR”
(Reverse) position.
N (Neutral):
Neither the forward nor reverse gear is engaged. The
engine can be started in this position. You may shift to
the \bN” (Neutral) position and restart a stalled engine
while the vehicle is moving.
D (Drive):
Use this position for all normal forward driving.
L (Low):
Use this position when climbing steep hills slowly or
driving slowly through deep snow, sand or mud, or for
maximum engine bra\fing on steep downhill grades.SPORT mode switch
JVC0027XRight-Hand Drive (RHD) modelTo select the SPORT mode, push the SPORT mode
switch with the selector lever in the \bD” (Drive)
position. The SPORT mode indicator light
in the
meter panel illuminates. To turn off the SPORT mode,
push the SPORT mode switch again. The SPORT
mode indicator light will turn off. When the selector
lever is shifted to any position other than \bD”, the
SPORT mode will be automatically turned off.
“OFF” position:
For normal driving and fuel economy, use the \bOFF”
position.
“ON” position:
For driving up or down long slopes where engine
bra\fing is necessary, or for powerful acceleration, use
the \bON” position. The transmission will automatically
select a different gear ratio, allowing the engine to
provide high output.
When driving conditions change, push the switch to
turn the SPORT mode off.
Remember not to drive at high speeds for extended
periods of time with the SPORT mode in the \bON”
position. This reduces fuel economy.
Accelerator downshift - in the \bD” position -
For passing or climbing hills, depress the accelerator
pedal to the floor. This shifts the transmission down
into a lower gear, depending on the vehicle speed.
Shift loc\f release
JVC0028XRight-Hand Drive (RHD) modelIf the battery charge is low or discharged, the selector
lever may not be moved from the \bP” (Par\f) position
even with the bra\fe pedal depressed and the selector
lever button pushed.
To move the selector lever, perform the following
procedure:
1. Model with Intelligent Key system:
Place the ignition switch in the \bOFF” or \bLOCK”
position.
Model without Intelligent Key system:
Place the ignition switch in the \bLOCK” position,
and remove the \fey if it is inserted.
2. Apply the par\fing bra\fe.
3. Depress the shift loc\f release button.
4. Push the selector lever button and move the selector lever to the \bN” (Neutral) position while
holding down the shift loc\f release.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5. Place the ignition switch in the “ON” \fosition tounlock the steering wheel.
\bhe vehicle may be moved to the desired location.
Re\flace the removed shift lock release cover after the
o\feration.
For model with Intelligent Key system: If the battery is
discharged com\fletely, the steering wheel cannot be
unlocked. Do not move the vehicle with the steering
wheel locked.
If the selector lever cannot be moved out of the “P”
(Park) \fosition, have a RENAUL\b dealer check the
CV\b system as soon as \fossible.
WARNING:
If the selector lever cannot be moved from the
“P” (Park) position while the engine is running
and the brake pedal is depressed, the stop lights
may not work. Malfunctioning stop lights could
cause an accident injuring yourself and others.
High fluid tem\ferature \frotection mode
\bhis transmission has a high fluid tem\ferature \frotec-
tion mode. If the fluid tem\ferature becomes too high
(for exam\fle, when climbing stee\f grades in high
tem\ferature with heavy loads, such as when towing a
trailer) , engine \fower and, under some conditions,
vehicle s\feed will be decreased automatically to
reduce the chance of transmission damage. Vehicle
s\feed can be controlled with the accelerator \fedal,
but engine and vehicle s\feed may be limited.
Fail-safe
When the fail-safe o\feration occurs, the CV\b will not
be shifted to the selected driving \fosition.
If the vehicle is driven under extreme conditions,
such as excessive wheel spinning and subse-
quent hard braking, the fail-safe system may be
activated. This will occur even if all electrical
circuits are functioning properly. In this case,
place the ignition switch in the “OFF”position
and wait for 10 seconds. Then turn the ignition
switch back to the “ON”position. The vehicle
should return to its normal operating condition.
If it does not return to its normal operating
condition, have a RENAULT dealer check the
transmission and repair it if necessary.
WARNING:
When the fail-safe operation occurs, vehicle
speed may be gradually reduced. The reduced
speed may be lower than other traffic, which
could increase the chance of a collision. Be
especially careful when driving. If necessary, pull
to the side of the road at a safe place and allow
the transmission to return to normal operation,
or have it repaired if necessary.
DRIVING WI\bH MANUAL \bRANSMISSION
(M\b)
WARNING:
. Do not downshift abruptly on slippery roads.
This may cause a loss of vehicle control.
. Do not over-rev the engine when shifting to
a lower gear. This may cause a loss of
vehicle control or engine damage.
CAUTION:
.Do not rest your foot on the clutch pedal
while driving. This may damage the clutch
system.
. Fully depress the clutch pedal before shift-
ing to help prevent transmission damage.
. Stop the vehicle completely before shifting
into the “R” (Reverse) position.
. When the vehicle is stopped for a period of
time, for example waiting at stoplights, shift
to the “N” (Neutral) position and release the
clutch pedal with the foot brake pedal
depressed.
. Do not shift to the "N" (Neutral) position
while driving. Doing so may result in an
accident due to loss of engine braking.
Starting and driving5-17
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-22Starting and driving
.The driver ’s seat belt is unfastened, or
driver’s door is open (for MT model) .
. The hood is open.
The Stop/Start System is al\fays engaged at the start
o\b a journey (once the engine has been started) . The
engine is automatically stopped and restarted during
the journey i\b conditions are suitable.
STOP/START SYSTEM DISPLAY AND IN-
DICATORS
Engine stop
JVS0071X
When the engine is stopped the in\bormation is
displayed \bor a \be\f seconds.
Vehicle information display: 1. Engine stop guidance
Instrument panel: 2. Stop/Start System indicator light
See “Vehicle in\bormation display” (P.2-20) about the
display. NOTE:
Automatic engine restart is possible whenever
the Stop/Start System indicator light is illumi-
nated in the meter.
CO2 saved
JVS0073X
Whilst the engine remains stopped the vehicle
in\bormation display sho\fs the accumulated quantity
(estimate) o\b carbon dioxide exhaust emissions pre-
vented by the Stop/Start System.
Vehicle information display:
1. CO2 saved in\bormation
Instrument panel: 2. Stop/Start System indicator light
. Push and hold the
button to reset the [CO2
Saved] value.
. The display can be s\fitched bet\feen Stop/Start
System in\bormation and drive computer in\borma-
tion by a short press o\b the
button.
System \bault
JVS0074X
When automatic restart is not possible the in\bormation
is displayed. The engine must be started by turning or
pushing the ignition s\fitch.
The message can be cleared by pressing the
button, restarting the engine, or turning or pushing the
ignition OFF.
Key LOCK \farning
JVS0081XType A
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
PRECAUTIONS ON CRUISE CONTROL
.If the cru\fse contro\b system ma\bfunct\fons, \ft
cance\bs automat\fca\b\by. The SET \fnd\fcator and the
cru\fse contro\b \fnd\fcator \b\fght w\f\b\b b\b\fnk to warn the
dr\fver.
. If the eng\fne coo\bant temperature becomes
excess\fve\by h\fgh, the cru\fse contro\b system w\f\b\b
be cance\bed automat\fca\b\by.
. If the SET \fnd\fcator and cru\fse contro\b \fnd\fcator
\b\fght b\b\fnk, turn off the cru\fse contro\b MAIN sw\ftch
and have the system checked by a RENAULT
dea\ber.
. The SET \fnd\fcator and cru\fse contro\b \fnd\fcator
\b\fght may b\b\fnk when the cru\fse contro\b MAIN
sw\ftch \fs turned on wh\f\be push\fng the RES+, SET
í, CANCEL sw\ftch. To proper\by set the cru\fse
contro\b system, use the fo\b\bow\fng procedures.
CRUISE CONTROL OPERATIONS
The cru\fse contro\b a\b\bows dr\fv\fng at speeds above 40
km/h (25 MPH) w\fthout keep\fng your foot on the
acce\berator peda\b.
The cru\fse contro\b w\f\b\b automat\fca\b\by be cance\bed \ff the
veh\fc\be s\bows down more than approx\fmate\by 13 km/h
(8 MPH) be\bow the set speed.
Mov\fng the se\bector \bever to the “N” (Neutra\b) pos\ft\fon
(Cont\fnuous\by Var\fab\be Transm\fss\fon mode\b) or depres-
s\fng the c\butch peda\b (Manua\b Transm\fss\fon mode\b) w\f\b\b
cance\b the cru\fse contro\b and the SET \fnd\fcator w\f\b\b
turn off.
The cru\fse contro\b sw\ftches are \bocated on the steer\fng
whee\b.
SSD0891
1. RES/+ sw\ftch
2. SET/í sw\ftch
3. CANCEL sw\ftch
4. Cru\fse contro\b MAIN sw\ftch
5. Speed \b\fm\fter MAIN sw\ftch (For deta\f\bs, see “Speed \b\fm\fter (\ff equ\fpped for Europe)” (P.5-26) .)
Cru\fse contro\b d\fsp\bay and \fnd\fcators (Type B
mode\b)
JVS0027X
The cru\fse contro\b operat\fng cond\ft\fon \fs shown on the
veh\fc\be \fnformat\fon d\fsp\bay and \fnstrument pane\b. Vehicle information display:
1. CRUISE \fnd\fcator
2. Set speed \fnd\fcator
Instrument panel: 3. Cru\fse contro\b \fnd\fcator \b\fght
4. SET \fnd\fcator \b\fght
Cru\fse contro\b d\fsp\bay and \fnd\fcators (Type C
mode\b)
JVS0028X
Vehicle information display:1. CRUISE \fnd\fcator
2. SET \fnd\fcator \b\fght
3. Set speed \fnd\fcator \b\fght
Instrument panel: 4. Cru\fse contro\b \fnd\fcator \b\fght
Turn\fng on cru\fse contro\b
Push the cru\fse contro\b MAIN sw\ftch. The cru\fse
contro\b \fnd\fcator \b\fght \f\b\bum\fnates. The set speed
\fnd\fcator shows “- - -”.
Starting and driving5-29
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
quickly become high enough to cause se-
vere or possibly fatal illness to people and
animals.
SSD0488
Left-Hand Drive (LHD) model
SSD0489
Right-Hand Drive (RHD) model1. Firmly apply the par\fing bra\fe.
\b. Automatic Transmission (AT)/Continuously Vari-able Transmission (CVT) model: Move the selector
lever to the “P” (Par\f) position.
Manual Transmission (MT) model: Move the shift
lever to the “R” (Reverse) position. When par\fing
on an uphill grade, move the shift lever to the “1”
(1st) position. 3. To help prevent the vehicle from moving into traffic
when par\fed on an incline, it is a good practice to
turn the wheels as illustrated.
HEADED DOWNHILL WITH CURB
*1
Turn the wheels into the curb and move the vehicle
forward until the curb side wheel gently touches
the curb. Then apply the par\fing bra\fe. HEADED UPHILL WITH CURB
*2
Turn the wheels away from the curb and allow the
vehicle to move bac\f until the curb side wheel
gently touches the curb. Then apply the par\fing
bra\fe.
HEADED UPHILL OR DOWNHILL, WITHOUT
CURB
*3
Turn the wheels toward the side of the road so the
vehicle will move away from the center of the road
if the vehicle moves. Then apply the par\fing bra\fe.
4. Model with Intelligent Key system:
Place the ignition switch in the “OFF” position.
Model without Intelligent Key system:
Place the ignition switch in the “LOCK” position
and remove the \fey.
NOTE:
For Model with Stop/Start (Idling Stop) System:
Use this system when the vehicle is stopped for
a period of time, for example waiting at stop-
lights.
Stop the engine with the ignition switch when
parking, etc. for an extended period of time.
Starting and driving5-31
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
5-34Starting and driving
JVS0031X
Measurement result:
The displa\f indicatin\b the measurement result
*B(“OK”, “DIFFICULT” or “NOT ADVISED” ) will appear in
the meter as illustrated.
CAUTION:
.This system provides you with an estimation
of the space in which parallel parking is
possible. Be aware that the system does not
guarantee that parking is always possible in
this space.
. This system may not be able to measure the
parking space correctly between the tall
vehicles such as trucks.
. When the tire pressure is not correct, this
system may not be able to measure the
parking space correctly.
. When replacing a tire with one other than a
genuine RENAULT tire (the same size as the
original tire) , have your vehicle adjusted by
RENAULT dealer. If genuine RENAULT tires
are not used, the system cannot guarantee
accurate measurement of the parking space. .
When the sensor is covered in snow or mud,
the system may not be able to measure the
parking space correctly. Always keep your
sensor clean.
JVS0029X
*1Parkin\b space measurement switch
*2ON indicator li\bht
Setting the level mode:
Dependin\b on \four drivin\b level, the modes can be
selected from the followin\b.
. Amateur .
Normal
. Expert
To set the mode, perform the followin\b procedure:
1. Push and hold the parkin\b space measurement switch
*1for at least 5 seconds. The buzzer then
sounds for 5 seconds.
2. Push the switch
*1the number of times needed
to set the desired mode within 10 seconds. After
10 seconds, the buzzer sounds the number of
times previousl\f pushed.
If the switch is not pushed, the buzzer will sound the
number of times that corresponds to the current mode
set.
The mode can be selected to "Amateur", "Normal" and
"Expert" b\f pushin\b the switch once to three times
while the buzzer sounds as follows:
. Push the switch once to select Amateur mode.
. Push the switch two times to select Normal mode.
. Push the switch three times to select Expert mode.
Each mode indicates the size of space in which
parkin\b is possible as follows:
. The Amateur mode indicates the lar\best parkin\b
space.
. The Normal mode indicates the medium parkin\b
space.
. The Expert mode indicates the smallest parkin\b
space.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
6 In case of emergency
Flat tire ..................\c..................\c..................\c.......................\c..................\c........ 6-2Stopping vehicle ..................\c..................\c..........................\c................. 6-2
\freparing tools ..................\c..................\c..................\c............................\c 6-2
Changing flat tire \bfor model with spare tire) ..................\c.......... 6-2
Repairing flat tire \bfor model with emergency tire puncture
repair kit) ..................\c..................\c...............................\c..................\c........ 6-5 Jump starting ..................\c..................\c..........................\c..................\c............ 6-8
\fush starting ..................\c..................\c..........................\c..................\c......... 6-10
If your vehicle overheats ..................\c..................\c..........................\c...... 6-10
Towing your vehicle ..................\c..................\c...............................\c.......... 6-11
Towing precautions ..................\c..................\c..................\c............... 6-11
Towing recommended by RENAULT ..................\c..................\c.. 6-11
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
WARNING:
.Never use wheel nuts which are not provided
with your vehicle. Incorrect wheel nuts or
improperly tightened wheel nuts may cause
the wheel to become loose or come off. This
could cause an accident.
. Never use oil or grease on the wheel studs
or nuts. This may cause the wheel nuts to
become loose.
. The T-type spare tire is designed for emer-
gency use only.
1. Clean any mud or dirt from the surface \fetween the wheel and hu\f.
2. Carefully put the spare tire on and ti\bhten the wheel nuts with your fin\bers. Check that all the
wheel nuts contact the wheel surface horizontally.
3. Ti\bhten the wheel nuts alternately and evenly, more than 2 times in the sequence illustrated (
*1-*4) , with the wheel nut wrench, until they are
ti\bht.
4. Lower the vehicle slowly until the tire touches the \bround.
5. Ti\bhten the wheel nuts securely, with the wheel nut wrench, in the sequence illustrated.
6. Lower the vehicle completely.
Tighten the wheel nuts to the specified torque
with a torque wrench as soon as possible. Wheel nut tightening torque:108 N·m (11 kg-m, 80 ft-lb)
The wheel nuts must be kept tightened to
specification at all times. It is recommended
that the wheel nuts be tightened to specification
at each lubrication interval.
WARNING:
Retighten the wheel nuts when the vehicle has
been driven for 1,000 km (600 miles) . (also in
cases of a flat tire, etc.)
Stowin\b dama\bed tire and tools
WARNING:
. Be sure that the tire, jack and tools used are
properly stored after use. Such items can
become dangerous projectiles in an accident
or sudden stop.
. The T-type spare tire is designed for emer-
gency use only.
1. Securely store the dama\bed tire, jack and tools used in the stora\be area.
2. Replace the spare tire cover and the floor cover.
3. Close the \fack door.
REPAIRING FLAT TIRE (for model with
emer\bency tire puncture repair kit)
The emer\bency tire puncture repair kit is supplied with
the vehicle instead of a spare tire. This repair kit must
\fe used for temporarily fixin\b a minor tire puncture.
After usin\b the repair kit, see a RENAULT dealer as
soon as possi\fle for tire inspection and repair/
replacement.
CAUTION:
. RENAULT recommends using only Genuine
RENAULT Emergency Tire Sealant provided
with your vehicle. Other tire sealants may
damage the valve stem seal which can cause
the tire to lose air pressure. .
Do not use the emergency tire puncture
repair kit provided with your vehicle on other
vehicles.
. Do not use the emergency tire puncture kit
for a purpose other than to inflate and check
the tire pressure for the vehicle.
. Use the emergency tire puncture kit only on
DC12V.
. Keep water and dust off the emergency tire
puncture kit.
. Do not disassemble or modify the emer-
gency tire puncture kit.
. Do not galvanize the emergency tire punc-
ture kit.
. Do not use the emergency tire puncture
repair kit under the following conditions.
Contact a RENAULT dealer or professional
road assistance.
— when the sealant has passed its expira-
tion date (shown on the label attached
to the bottle)
— when the cut or the puncture is approxi- mately 6 mm (0.25 in) or longer
— when the side of the tire is damaged
— when the vehicle has been driven with a considerable loss of air from the tire
— when the tire is completely displaced inside or outside the rim
— when the tire rim is damaged
— when two or more tires are flat
In case of emergency6-5
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
1. If the booster battery is in another vehicle*B,
\fosition the two vehicles*Aand*Bto bring the
batteries into close \fro\bimity to each other.
CAUTION:
If the battery of vehicle*Aequipped with the
Intelligent Key system is discharged, the ignition
switch cannot be moved from the “LOCK”
position and, if the steering lock is engaged,
the steering wheel cannot be moved. Connect
the jumper cables to the booster vehicle
*Bbefore turning the ignition switch and disenga-
ging the steering lock.
2. A\f\fly the \farking brake.
3. Automatic Transmission (AT)/Continuously Vari- able Transmission (CVT) model: Move the selector
lever to the “P” (Park) \fosition.
Manual Transmission (MT) model: Move the shift
lever to the “N” (Neutral) \fosition.
4. Switch off all unnecessary electrical systems (headlights, heater, air conditioner, etc.) .
5. Turn the ignition switch to the “LOCK” \fosition.
6. Remove the vent ca\fs, if equi\f\fed, on the battery.
7. Cover the battery with a firmly wrung out moist cloth to reduce the hazard of an e\b\flosion.
8. Connect the jum\fer cables in the sequence as illustrated (
*1,*2,*3,*4).
CAUTION:
.Always connect positive +to positive +and
negative 7to body ground, NOT to the
battery’s negative 7. .
Be sure that the jumper cables do not touch
moving parts in the engine compartment.
. Be sure that the jumper cable’s clamps do
not contact any other metal.
9. Start the engine of the booster vehicle
*Band let
it run for a few minutes.
10. De\fress the accelerator \fedal of the booster vehicle
*Bat about 2,000 r\fm.
11. Start the engine of the jum\fed vehicle
*Ain the
normal manner.
CAUTION:
. Never keep the starter motor engaged for
more than 10 seconds. If the engine does not
start right away, turn the ignition switch
“OFF” and wait at least 10 seconds before
trying again.
. If the starter motor does not start by pushing
the ignition switch, push the ignition switch
to the OFF position before trying again.
12. After the engine is started, carefully disconnect the jum\fer cables in the o\f\fosite sequence from
that illustrated (
*4,*3,*2,*1).
13. Remove and dis\fose of the cloth as it may be contaminated with corrosive acid.
14. Re\flace the vent ca\fs, if removed.
NOTE:
. For model with Stop/Start (Idling Stop)
System, use the special battery that is
enhanced in regard to the charge-discharge
capacity and life performance. Avoid using a
non-special battery for the Stop/Start (Idling
Stop) system, as this may cause early deterioration of the battery or a malfunction
of the Stop/Start (Idling Stop) system. For
the battery, it is recommended to use
Genuine RENAULT parts. For more informa-
tion, contact a RENAULT dealer.
. For model with Stop/Start (Idling Stop)
System, it may take some time until Stop/
Start (Idling Stop) System activates when
the battery is replaced or the battery term-
inal is disconnected for extended periods
and then reconnected.
In case of emergency6-9
&RQGLWLRQ