ECO mode RENAULT PULSE 2012 1.G Owner's Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2012, Model line: PULSE, Model: RENAULT PULSE 2012 1.GPages: 352, PDF Size: 6.46 MB
Page 133 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
Troubleshooting guide (model with type A, B, C, D, E, F audio unit):Symptom Cause and Countermeasure
Cannot play Check i\f the disc was inserted correctly.
Check i\f the disc is scratched or dirty.
Check i\f there is condensation inside the player, and i\f there is, wait until the condensation is \bone (about 1 hour) be\fore usin\b the
player.
I\f there is a temperature increase error, the CD player will play correctly a\fter it returns to the normal temperature.
I\f there is a mixture o\f music CD \files (CD-DA data) , MP3/WMA \files on a CD, only the music CD \files (CD-DA data) will be played.
Files with extensions other than “.MP3”, “.WMA”, “.mp3” or “.wma” cannot be played. In addition, the character codes and number o\f
characters \for \folder names and \file names should be in compliance with the speci\fications.
Check i\f the disc or the \file is \benerated in an irre\bular \format. This may occur dependin\b on the variation or the settin\b o\f MP3/WMA
writin\b applications or other text editin\b applications.
Check i\f the \finalization process, such as session close and disc close, is done \for the disc.
Check i\f the disc is protected by copyri\bht.
Poor sound quality Check i\f the disc is scratched or dirty.
It takes a relatively lon\b time be\fore
the music starts playin\b. I\f there are many \folder or \file levels on the MP3/WMA disc, or i\f it is a multisession disc, some time may be required be\fore the music
starts playin\b.
Music cuts o\f\f or skips The writin\b so\ftware and hardware combination mi\bht not match, or the writin\b speed, writin\b depth, writin\b width, etc., mi\bht not
match the speci\fications. Try usin\b the slowest writin\b speed.
Skippin\b with hi\bh bit rate \files Skippin\b may occur with lar\be quantities o\f data, such as \for hi\bh bit rate data.
Move immediately to the next son\b
when playin\b. When a non-MP3/WMA \file has been \biven an extension o\f “.MP3”, “.WMA”, “.mp3, “.wma”, or when play is prohibited by copyri\bht
protection, there will be approximately 5 seconds o\f no sound and then the player will skip to the next son\b.
The son\bs do not play back in the
desired order. The playback order is the order in which the \files were written by the writin\b so\ftware, so the \files mi\bht not play in the desired order.
Heater and air conditioner, and audio system4-13
& R Q G L W L R Q
Page 137 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
Audio main operation
The audio system operates when the ignition switch is
in the \fACC” or \fO\b” position.
POWER button:
To turn on the audio system, push the Power button.
.The system will turn on in the mode, (radio or CD)
which was used immediately before the system
was turned off.
. If there is no CD loaded, the radio will be turned
on.
To turn off the audio system, push the Power button.
Volume control:
To control the volume, turn the VOL control knob.
Turn the knob clockwise to make the sound louder.
Turn the knob counterclockwise to make the sound
quieter.
MENU button:
To change the audio settings (BASS, TREBLE,
FADER, BALA\bCE, BEEP and CLOCK) , push the
button to select the mode while the CD or radio is
on.
Push the
button until the desired mode appears
on the display.
BASS ?TREBLE ?FADE ?BALA\bCE ?BEEP
O\b ?CLOCK
Audio setting
Push the SEEK/TRACK button (
or) or
TU\bE/FF·REW/FOLDER button (or) to
adjust while the following audio setting is displayed.
:( í) to decrease / (+) to increase
:( í) to decrease / (+) to increase
: (F) to front fade / (R) to rear fade
: (R) to right balance / (L) to left balance
Once the audio settings are set to the desired level,
push the
button until the radio or CD display
appears.
If no action is performed for approximately 5 seconds,
the audio settings mode will automatically return to the
normal mode.
Beep setting
To turn the beep sound off or on, push the SEEK/
TRACK button
oror TU\bE/FF·REW/
FOLDER buttonoruntil the desired mode
is displayed. This turns on or off the beep sound when
audio buttons are pushed.
Clock setting
To display the clock on the screen, push the SEEK/
TRACK button
oror TU\bE/FF·REW/
FOLDER buttonorto select CLOCK O\b.
1. Turn the clock display on.
2. Push the
button while CLOCK O\b is on the
display. The hour and minute digits blink.
3. To adjust the hours, push the SEEK/TRACK button
or.
4. To adjust the minutes, push the TU\bE/FF·REW/ FOLDER button
or.
If no user input is detected for 10 seconds, or when
the \fME\bU” button is pushed, the clock setting mode
will automatically return to the normal mode.
CD player operation
SAA3123
The audio system operates when the ignition switch is
in the \fACC” or \fO\b” position.
Loading:
Insert a CD into the slot with the label side facing up.
The CD will be guided automatically into the slot and
will start playing. To stop playing, push the Power
button.
CAUTION:
Do not force the compact disc into the slot. This
could damage the player.
button:
When the
button is pushed while a CD is loaded,
the CD will start playing automatically.
button:
When the
button is pushed while a CD with a title
is being played, the display will change as follows:
Heater and air conditioner, and audio system4-17
& R Q G L W L R Q
Page 138 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
4-18Heater and air conditioner, and audio system
CD:
CD with MP3 or WMA:
SEEK/TRACK button:
Whe\f the
butto\f is \bushed while a CD is bei\fg
\blayed, the \brese\ft track will be adva\fced a\fd move to
the \fext track. Push the
butto\f several times to
ski\b forward tracks. The CD will adva\fce the \fumber
of times the butto\f is \bushed. Whe\f the last track of
the CD is forwarded, the first track will be \blayed.
Whe\f the
butto\f is \bushed while a CD is bei\fg
\blayed, the \brese\ft track will start over from the
begi\f\fi\fg of the curre\ft track. Push the
butto\f
several times to ski\b back tracks. The CD will rewi\fd
the \fumber of times the butto\f is \bushed. Whe\f the
first track of the CD is rewou\fd, the last track will be
\blayed.
TUNE/FF·REW/FOLDER button:
Whe\f the
orbutto\f is \bushed a\fd held while
a CD is bei\fg \blayed, the CD will be \blayed while
forwardi\fg or rewi\fdi\fg. Whe\f the butto\f is released,
the CD will retur\f to the \formal \blay s\beed.
Whe\f the
orbutto\f is \bushed while a CD
with MP3 or WMA is bei\fg \blayed, the first track i\f the
\fext or the \brevious folder will be \blayed.
button:
Whe\f the
butto\f is \bushed while a CD is bei\fg
\blayed, the first 10 seco\fds of all the tracks will be
\blayed.
Whe\f the
butto\f is \bushed agai\f, the CD will
retur\f to \formal \blay from the track which is \blayi\fg.
(Repeat) button:
To cha\fge the \blay setti\fgs, \bush the
butto\f to
select the mode.
CD:
RPT DISC ?RPT TRACK
CD with MP3 or WMA:
RPT DISC ?RPT FOLDER ?RPT TRACK
RPT DISC:
All the tracks of the CD will be \blayed co\fti\fuously i\f
seque\ftial order. The dis\blay i\fdicates \fo symbol
mark. While the
butto\f is \bushed, the dis\blay
i\fdicates “RPT DISC”.
RPT TRACK:
The selected track of the CD will be \blayed co\f-
ti\fuously. While the
butto\f is \bushed, the dis\blay
i\fdicates “RPT TRACK”.
RPT FOLDER:
All the tracks of selected folder will be \blayed
co\fti\fuously i\f seque\ftial order (CD with MP3 or
WMA o\fly) . While the
butto\f is \bushed, the
dis\blay i\fdicates “RPT FOLDER”.
(Random) button:
To cha\fge the \blay seque\fce, \bush the
butto\f to
select the mode.
CD:
RDM DISC ?RPT DISC
CD with MP3 or WMA:
RDM DISC ?RDM FOLDER ?RPT DISC
RPT DISC:
All the tracks of the CD will be \blayed co\fti\fuously i\f
seque\ftial order. The dis\blay i\fdicates \fo symbol
mark. While the
butto\f is \bushed, the dis\blay
i\fdicates “RPT DISC”.
RDM DISC:
All the tracks or folders (CD with MP3 or WMA o\fly) of
the CD will be \blayed co\fti\fuously i\f ra\fdom order.
While the
butto\f is \bushed, the dis\blay i\fdicates
“RDM DISC”.
RDM FOLDER:
All the tracks of the selected folder will be \blayed
co\fti\fuously i\f ra\fdom order (CD with MP3 or WMA
o\fly) . While the
butto\f is \bushed, the dis\blay
i\fdicates “RDM FOLDER”.
MUTE button:
Press the
butto\f to \bause the track.
CD EJECT button:
To eject a CD, \bush the CD EJECT
butto\f.
Whe\f the
butto\f is \bushed twice, the CD will be
ejected further, a\fd the CD ca\f be removed with ease.
If a CD is ejected by \bushi\fg the
butto\f, a\fd it is
& R Q G L W L R Q
Page 141 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
16. Radio memory buttons (1 - 6\f
17. ME\bU button
Audio main operation
The audio system operates when the ignition switch is
in the “ACC” or “O\b” position.
POWER button:
To turn on the audio system, push the Power button.
.The system will turn on in the mode, (radio or CD\f
which was used immediately before the system
was turned off.
. If there is no CD loaded, the radio will be turned
on.
To turn off the audio system, push the Power button.
Volume control:
To control the volume, turn the VOL control knob.
Turn the knob clockwise to make the sound louder.
Turn the knob counterclockwise to make the sound
quieter.
Sound preference button:
To enter the audio mode (radio, CD or AUX\f , push the
button. When no CD is loaded and AUX is not
connected , the audio system will automatically switch
to the radio mode.
To change the audio settings (BASS, TREBLE,
FADER, BALA\bCE\f , push the
button to select
the mode.
BASS ?TREBLE ?BALA\bCE ?FADER ?BASS
To adjust each audio setting, push the SEEK/TRACK
button or Tune button. BASS: ( í\f to decrease / (+\f to increase
TREB(LE\f: ( í\f to decrease / (+\f to increase
BAL
(A\bCE\f:
(R\f to right balance / (L\f to left balance
FADE(R\f: (F\f to front fade / (R\f to rear fade
If the audio settings mode is unchanged for approxi-
mately 8 seconds, the audio settings mode will
automatically return to the normal mode.
MENU button:
To change the audio settings (BEEP and CLOCK\f ,
push the
button to select the mode while the CD
or radio is on.
Push the
button until the desired mode appears
on the display.
BEEP O\b ?CLOCK
To turn the beep sound off or on, push the SEEK/
TRACK button
oror TU\bE/FF·REW/
FOLDER buttonoruntil the desired mode
is displayed. This turns on or off the beep sound when
audio buttons are pushed.
Clock display:
To display the clock on the screen, perform the
following operations.
1. Push the
button repeatedly until CLOCK O\b
or OFF appears on the display while the audio
system is on.
2. Push the SEEK/TRACK button
oror
TU\bE/FF·REW/FOLDER buttonorto
select CLOCK O\b. Clock adjustment:
To adjust the clock, turn the clock display on and
perform the following operations.
1. Push the
button while CLOCK O\b is on the
display. The hour and minute digits blink.
2. To adjust the hours, push the SEEK/TRACK button
or.
3. To adjust the minutes, push the TU\bE button
or.
If no user input is detected for 10 seconds, or when
the “ME\bU” button is pushed, the clock setting mode
will automatically return to the normal mode.
CD player operation
JVH0002X
The audio system operates when the ignition switch is
in the “ACC” or “O\b” position.
Loading:
Insert a CD into the slot with the label side facing up.
The CD will be guided automatically into the slot and
will start playing. To stop playing, push the Power
button.
Heater and air conditioner, and audio system4-21
& R Q G L W L R Q
Page 142 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
4-22Heater and air conditioner, and audio system
CAUTION:
Do not force the compact disc into the slot. This
could damage the player.
button:
When the
button is pushed while a C\f is loaded,
the C\f will start playin\b automatically.
SEEK/TRACK button:
When the
button is pushed while a C\f is bein\b
played, the present track will be advanced and move to
the next track. Push the
button several times to
skip forward tracks. The C\f will advance the number
of times the button is pushed. When the last track of
the C\f is forwarded, the first track will be played.
When the
button is pushed while a C\f is bein\b
played, the present track will start over from the
be\binnin\b of the current track. Push the
button
several times to skip back tracks. The C\f will rewind
the number of times the button is pushed. When the
first track of the C\f is rewound, the last track will be
played.
TUNE/FF·REW/FOLDER button:
When the
orbutton is pushed and held while
a C\f is bein\b played, the C\f will be played while
forwardin\b or rewindin\b. When the button is released,
the C\f will return to the normal play speed.
button:
When the
button is pushed while a C\f is bein\b
played, the first 10 seconds of all the tracks will be
played.
When the
button is pushed a\bain, the C\f will
return to normal play from the track which is playin\b.
(Repeat) button:
To chan\be the play settin\bs, push the
button to
select the mode.
C\f:
RPT \fISC ?RPT TRACK
All the tracks of the C\f will be played continuously in
sequential order. The display indicates no symbol
mark. While the
button is pushed, the display
indicates “RPT \fISC”.
RPT TRACK:
The selected track of the C\f will be played con-
tinuously. While the
button is pushed, the display
indicates “RPT TRACK”.
(Random) button:
To chan\be the play sequence, push the
button to
select the mode.
C\f:
R\fM \fISC ?RPT \fISC
All the tracks of the C\f will be played continuously in
sequential order. The display indicates no symbol
mark. While the
button is pushed, the display
indicates “RPT \fISC”.
R\fM \fISC:
All the tracks of the C\f will be played continuously in random order. While the
button is pushed, the
display indicates “R\fM \fISC”.
MUTE button:
Press the
button to pause the track.
CD EJECT button:
To eject a C\f, push the C\f EJECT
button.
If a C\f is ejected by pushin\b the
button, and it is
not taken out from the loadin\b slot, the C\f will
automatically be reloaded to the slot to protect the C\f
(12 cm discs only) .
AUX button:
The AUX IN jack is located on the audio unit. The AUX
IN audio input jack accepts any standard analo\b audio
input such as from a portable cassette tape, C\f player,
MP3 player or laptop computers.
Push the AUX button to play a compatible device when
it is plu\b\bed into the AUX IN jack.
WARNING:
. Do not allow the cable or an external device
connected to the AUX terminal to affect your
driving.
. Connect a stereo mini-plug (3.5 mm in
diameter) cable to the AUX IN jack. If a
monaural mini-plug cable is used, the audio
will not output correctly.
& R Q G L W L R Q
Page 145 of 352
![RENAULT PULSE 2012 1.G Owners Manual
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
16. Radio memory buttons
17. RP\f (Repeat)\bMIX (Mix play) button
Anti-theft system (if equipped)
\](/img/7/1587/w960_1587-144.png "RENAULT PULSE 2012 1.G Owners Manual
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
16. Radio memory buttons
17. RP\f (Repeat)\bMIX (Mix play) button
Anti-theft system (if equipped)
\")
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
16. Radio memory buttons
17. RP\f (Repeat)\bMIX (Mix play) button
Anti-theft system (if equipped)
\fhis unit can only be activated when the ignition switch
for Anti-\fheft System is in the “ACC” or “ON” position.
Each radio is uniquely matched to the vehicle’s
immobilizer and therefore cannot be transferred to
any other vehicle.
Audio main operation
\fhe audio system operates when the ignition switch is
in the “ACC” or “ON” position.
POWER ON/OFF button:
\fo turn on the audio system, push the POWER ON\b
OFF button.
.\fhe system will turn on in the mode, (radio or CD)
which was used immediately before the system
was turned off.
. If there is no CD loaded, the radio will be turned
on.
\fo turn off the audio system, push the POWER ON\b
OFF button.
Volume control:
\fo control the volume, turn the VOLUME control dial.
\furn the VOLUME control dial clockwise to make the
sound louder.
\furn the VOLUME control dial counterclockwise to
make the sound quieter.
Sound preference button:
\fo enter the audio mode (radio or CD) , push the
button. When no CD is loaded, the audio system will
automatically switch to the radio mode. \fo change the audio settings (BASS, \fREBLE,
FADER, BALANCE, EQ) , push the
button or
EN\fER button to select the mode.
BASS ?\fREBLE ?BALANCE ?FADER ?EQ ?
BASS
\fo adjust each audio setting, turn the VOL control dial
clockwise or counterclockwise.
BASS: ( í) to decrease \b (+) to increase
\fREB(LE): ( í) to decrease \b (+) to increase
BAL(ANCE): (R) to right balance \b (L) to left balance
FADE(R): (F) to front fade \b (R) to rear fade
EQ (Equalizer): Use this control to change the preset
sound mode for CD play.
\furn the MENU\bVOL dial clockwise or counterclock-
wise. \fhe mode will change as follows:
OFF ⇔ENHANCE
If the audio settings mode is unchanged for approxi-
mately 8 seconds, the audio settings mode will
automatically return to the normal mode.
MENU button:
\fo configure the SPEED volume and BEEP settings,
perform the following procedure:
1. Push the MENU button.
2. \furn the VOLUME dial clockwise or counter- clockwise. \fhe display message will change as
follows:
PHONE SE\fUP ⇔SPEED VOL⇔CLOCK ⇔
BEEP ⇔PHONE SE\fUP
. When SPEED VOL appears on the display, briefly
push on the EN\fER button then turn the VOLUME
dial clockwise or counterclockwise to adjust the
level of the volume. Adjusting the setting to 0 (zero) turns off the
speed volume feature. Increasing the speed
volume setting results in the audio volume
increasing more rapidly with vehicle speed. Push
the EN\fER button again to save the setting.
. When BEEP appears on the display, briefly push
the EN\fER button and then turn the VOLUME dial
clockwise or counterclockwise to switch the beep
sound on or off. Push the EN\fER button again to
save the setting.
\fo configure Alternative Frequency, Regional and
Language settings, perform the following procedure:
1. Push and hold the MENU button for at least 1.5 seconds.
2. \furn the VOLUME dial clockwise or counter- clockwise. \fhe display message will change as
follows:
AF⇔REG ⇔LANGUAGE ⇔AF
. \fo activate or deactivate the AF and REG mode,
briefly push on the EN\fER button when AF or
REG appears on the display and turn the
VOLUME dial clockwise or counterclockwise to
switch between the off or on position. After
selection, push the EN\fER button to confirm the
settings.
— When the AF mode is enabled, the audio unit
will automatically re-tune to a stronger fre-
quency if the radio signal becomes weak.
— When the REG mode is enabled, the audio unit will maintain and hold the station which is
broadcasting local (regional) programmes.
. \fo change the display language, briefly push the
EN\fER button when LANGUAGE appears on the
display then turn the VOLUME dial clockwise or
counterclockwise to select the appropriate lan-
guage setting.
Heater and air conditioner, and audio system4-25
& R Q G L W L R Q
Page 148 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
4-28Heater and air conditioner, and audio system
*1*2*3*4*5*6Radio memory buttons:
The audio system can store u\f to 18 FM station
\brequencies (six in each o\b FM 1, FM 2 and FM T) , 6
MW and 6 LW station \brequencies.
To store the station \brequency manually:
1. Tune to the desired broadcasting station \bre- quency by using the
orbutton.
2. Push and hold a radio memory button
*1-*6until a bee\f sounds. (The radio mutes when the
memory button is \fushed.)
3. The channel indicator will dis\flay and the radio mute disengages, indicating that the memory is
stored \fro\ferly.
4. Per\borm ste\fs 1 - 3 \bor all other memory buttons.
I\b the battery cable is disconnected, or i\b the audio \buse
blows, the radio memory will be erased. In such a case,
reset the desired stations.
Radio data system (RDS)
Alternative Frequency (AF):
. The AF \bunction o\ferates in the FM (radio) and CD
modes.
. When the AF mode is set to “ON” in the user
setu\f menu mode, the AF indicator illuminates.
For activation or deactivation details, see “Audio main
o\feration” (P.4-25) .
. Automatic switching function
This \bunction com\fares the strengths o\b the
signals o\b all the stations on the AF list and
selects the station with the o\ftimum rece\ftion
conditions.
. Program Information (PI) search
Program In\bormation (PI) search begins automati- cally i\b no suitable station is \bound with the above
automatic switching \bunction. The PI search
\bunction checks each RDS station with the same
PI code. During this time the sound is muted and
“PI SEARCH” is dis\flayed. The PI search o\fera-
tion sto\fs when a suitable station is \bound. I\b no
station is \bound once all the \brequencies have been
searched, the radio returns to the \frevious
\brequency.
. Enhanced Other Network (EON) data update
(This function also operates when the AF
mode is off.)
When EON data is being received, this enables
automatic retuning o\b other \freset stations on the
same network. Also, network linked services can
be used. The EON indicator turns on during the
rece\ftion o\b RDS EON stations in the FM mode.
RDS functions:
. Programme Service (PS) function (station
name display function)
When an RDS station is tuned in with seek or
manual tuning, the RDS data is received and the
Program Service (PS) name is dis\flayed.
. Emergency broadcast interrupt function
(ALARM INTERRUPTION —EBU SPEC FOR
INFO)
When the radio receives PTY code 31 (an
emergency broadcast code) , the sound is inter-
ru\fted, the emergency broadcast is heard, and
“PTY31 ALARM” is dis\flayed. The volume level at
this time is the same as that \bor tra\b\bic announce-
ments. Once the emergency broadcast is \binished,
the unit immediately returns to the \frevious
source.
. REG (Regional) mode
Some local radio stations are linked together according to their region because they only o\b\ber
limited coverage due to their limited number o\b
transmitters. I\b the signal \brom one station be-
comes weak while you are driving around, RDS
mode will switch to another local station in the
region with a stronger signal.
When the REG mode is activated in the FM band
and the radio receiver is tuned to a local radio
station, it will kee\f receiving this radio station
without switching to another local station. For
activation or deactivation details, see “Audio main
o\feration” (P.4-25) .
Traffic Announcement (TA):
. The TA \bunction o\ferates in the FM and CD
modes.
. The TA mode is turned on or o\b\b when the TA/
NEWS button is \fushed \bor less than 2 seconds.
. The TA mode o\ferates regardless o\b whether the
AF mode is on or o\b\b.
. “TA ON” is dis\flayed when the TA mode is turned
on, and the TA indicator turns on. “TA OFF” is
dis\flayed when the TA mode is turned o\b\b, and the
TA indicator turns o\b\b.
The \bollowing \bunctions o\ferate when the TA mode is
on:
. Traffic announcement interrupt function
When a tra\b\bic announcement is received, the
announcement is tuned in and the volume
increases to the set level.
Once the tra\b\bic announcement is \binished, the unit
returns to the source which was set be\bore the
tra\b\bic announcement started, and the volume
returns to the \frevious level. For EON stations,
the radio is interru\fted by another EON station
with tra\b\bic announcements.
The tra\b\bic announcement interru\ft mode is
& R Q G L W L R Q
Page 151 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
Audio main operation
The audio system operates when the ignition switch is
in the \fACC” or \fO\b” position.
POWER button:
To turn on the audio system, push the Power button.
.The system will turn on in the mode, (radio or CD)
which was used immediately before the system
was turned off.
. If there is no CD loaded, the radio will be turned
on.
To turn off the audio system, push the PWR button.
Volume control:
To control the volume, turn the VOLUME control knob.
Turn the knob clockwise to make the sound louder.
Turn the knob counterclockwise to make the sound
quieter.
MENU button:
To change the audio settings, push the
button to
select the mode while the CD or radio is on.
Push the
button until the desired mode appears
on the display.
BASS ?TREBLE ?FADE ?BALA\bCE ?BEEP ?
CLOCK ?BASS
Push the SEEK/TRACK button (
or) or
TU\bE/FF·REW/FOLDER button (or) to
adjust the audio settings.
:( í) to decrease / (+) to increase
:( í) to decrease / (+) to increase
: (F) to front fade / (R) to rear fade
: (R) to right balance / (L) to left balance
Once the audio settings are set to the desired level, push the
button until the radio or CD display
appears.
If no action is performed for approximately 5 seconds,
the audio settings mode will automatically return to the
normal mode.
To turn the beep sound off or on, push the SEEK/
TRACK button
oror TU\bE/FF·REW/
FOLDER buttonoruntil the desired
mode is displayed. This turns on or off the beep sound
when audio buttons are pushed.
Clock display:
To display the clock on the screen, perform the
following operations.
1. Push the
button repeatedly until CLOCK O\b
or OFF appears on the display while the audio
system is on.
2. Push the SEEK/TRACK button
oror
TU\bE/FF·REW/FOLDER buttonorto select CLOCK O\b.
Clock adjustment:
To adjust the clock, turn the clock display on and
perform the following operations.
1. Push the
button while CLOCK O\b is on the
display. The hour and minute digits blink.
2. To adjust the hours, push the SEEK/TRACK button
or.
3. To adjust the minutes, push the TU\bE/FF·REW/ FOLDER button
or.
If no user input is detected for 10 seconds, or when
the \fME\bU” button is pushed, the clock setting mode
will automatically return to the normal mode.
CD player operation
JVH0012X
The audio system operates when the ignition switch is
in the \fACC” or \fO\b” position.
Loading:
Insert a CD into the slot with the label side facing up.
The CD will be guided automatically into the slot and
will start playing. To stop playing, push the Power
button.
CAUTION:
Do not force the compact disc into the slot. This
could damage the player.
button:
When the
button is pushed while a CD is loaded,
the CD will start playing automatically.
button:
When the
button is pushed while a CD with a title
is being played, the display will change as follows:
Heater and air conditioner, and audio system4-31
& R Q G L W L R Q
Page 158 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
4-38Heater and air conditioner, and audio system
The audio system operates whe\f the ig\fitio\f switch is
i\f the “\bCC” or “ON” positio\f.
FM-AM button:
Whe\f the
/butto\f is pushed while the audio
system is off, the audio system a\fd the radio will tur\f
o\f. Whe\f the
/butto\f is pushed while the CD
player is already operati\fg, it will automatically tur\f off
a\fd the radio will tur\f o\f.
To cha\fge the radio ba\fd, push the
/butto\f
u\ftil the preferred ba\fd appears.
. For FM
FM 1 ?FM 2 ?FM T
. For \bM
MW ?LW ?MW
Duri\fg FM receptio\f, whe\f the
butto\f is pushed
for lo\fger tha\f 1.5 seco\fds, statio\fs are searched for
a\fd the 6 statio\fs of the FM T ba\fd. The sou\fd is
muted u\ftil the auto store operatio\f is completed,
upo\f which preset cha\f\fel 1 is automatically tu\fed i\f.
TUNE button:
Whe\f adjusti\fg the broadcasti\fg statio\f freque\fcy
ma\fually, push the
orbutto\f u\ftil the
preferred freque\fcy is obtai\fed.
The freque\fcy cha\fges i\f steps of 100 kHz o\f the FM
ba\fd, 9 kHz o\f the MW ba\fd, a\fd 3 kHz o\f the LW
ba\fd.
SEEK button:
Whe\f adjusti\fg the broadcasti\fg statio\f freque\fcy
automatically, push the
orbutto\f. Whe\f the
system detects a broadcasti\fg statio\f, it will stop at
that statio\f.
*1*2*3*4*5*6Radio memory buttons:
The audio system ca\f store up to 18 FM statio\f
freque\fcies (six i\f each of FM 1, FM 2 a\fd FM T) , 6
MW a\fd 6 LW statio\f freque\fcies.
To store the statio\f freque\fcy ma\fually:
1. Tu\fe to the preferred broadcasti\fg statio\f fre- que\fcy by usi\fg the
orbutto\f.
2. Push a\fd hold a radio memory butto\f
*1-*6u\ftil a beep sou\fds. (The radio mutes whe\f the
memory butto\f is pushed.)
3. The cha\f\fel i\fdicator will be displayed a\fd the radio mute will be ca\fcelled, i\fdicati\fg that the
memory is stored properly.
4. Perform steps 1 - 3 for all other memory butto\fs.
If the battery cable is disco\f\fected, or if the audio fuse
blows, the radio memory will be erased. If this occurs,
reset the desired statio\fs.
Radio data system (RDS)
Alternative Frequency (AF):
. The \bF fu\fctio\f operates i\f the FM (radio) a\fd CD
modes.
. Whe\f the \bF mode is set to “ON” i\f the user
setup me\fu mode, the \bF i\fdicator illumi\fates.
For activatio\f or deactivatio\f, use the MENU butto\f.
(Details are explai\fed later i\f this sectio\f.)
. Automatic switching function
This fu\fctio\f compares the stre\fgths of the
sig\fals of all the statio\fs o\f the \bF list a\fd
selects the statio\f with the optimum receptio\f
co\fditio\fs.
. Program Information (PI) search
Program I\fformatio\f (PI) search begi\fs automati- cally if \fo suitable statio\f is fou\fd with the above
automatic switchi\fg fu\fctio\f. The PI search
fu\fctio\f checks each RDS statio\f with the same
PI code. Duri\fg this time the sou\fd is muted a\fd
“PI SE\bRCH” is displayed. The PI search opera-
tio\f stops whe\f a suitable statio\f is fou\fd. If \fo
statio\f is fou\fd o\fce all the freque\fcies have bee\f
searched, the radio retur\fs to the previous
freque\fcy.
. Enhanced Other Network (EON) data update
(This function also operates when the AF
mode is off.)
Whe\f EON data is bei\fg received, this e\fables
automatic retu\fi\fg of other preset statio\fs o\f the
same \fetwork. \blso, \fetwork li\fked services ca\f
be used. The EON i\fdicator tur\fs o\f duri\fg
receptio\f of RDS EON statio\fs i\f the FM mode.
RDS functions:
. Programme Service (PS) function (station
name display function)
Whe\f a\f RDS statio\f is tu\fed i\f with seek or
ma\fual tu\fi\fg, RDS data is received a\fd the
Program Service (PS) \fame is displayed.
. Emergency broadcast interrupt function
(ALARM INTERRUPTION —EBU SPEC FOR
INFO)
Whe\f the radio receives PTY code 31 (a\f
emerge\fcy broadcast code) , the sou\fd is i\fter-
rupted, the emerge\fcy broadcast is heard, a\fd
“PTY31 \bL\bRM” is displayed. The volume level at
this time is the same as that for traffic a\f\fou\fce-
me\fts. O\fce the emerge\fcy broadcast is fi\fished,
the u\fit immediately retur\fs to the previous
source.
. REG (Regional) mode
Some local radio statio\fs are li\fked together
& R Q G L W L R Q
Page 159 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
according to their region because they only offer
limited coverage due to their limited number of
transmitters\f If the signal from one station be-
comes wea\b while you are driving around, RDS
mode will switch to another local station in the
region with a stronger signal\f
When the REG mode is activated in the FM band
and the radio receiver is tuned to a local radio
station, it will \beep receiving this radio station
without switching to another local station\f For
activation or deactivation, use the MENU button\f
(Details are explained later in this section\f)
Traffic Announcement (TA):
. The TA function operates in the FM and CD
modes\f
. The TA mode is turned on or off when the TA
button is pushed for less than 2 seconds\f
. The TA mode operates regardless of whether the
AF mode is on or off\f
. “TA ON” is displayed when the TA mode is turned
on, and the TA indicator turns on\f “TA OFF” is
displayed when the TA mode is turned off, and the
TA indicator turns off\f
The following functions operate when the TA mode is
on:
. Traffic announcement interrupt function
When a traffic announcement is received, the
announcement is tuned in and the volume
increases to the set level\f
Once the traffic announcement is finished, the unit
returns to the source which was set before the
traffic announcement started, and the volume
returns to the previous level\f For EON stations,
the radio is interrupted by another EON station
with traffic announcements\f
The traffic announcement interrupt mode is cancelled if the TA button is pushed during a
traffic announcement\f The TA mode returns to the
standby mode and the audio unit returns to the
previous source\f
News mode
When the NEWS button is pushed for longer than 2
seconds in the FM mode, the news function is
activated\f “NEWS” is displayed for 3 seconds and
the NEWS indicator appears on the display\f
When the news function is activated, the radio
receives a news code from the FM broadcasting news
station and the actual playing mode will be interrupted\f
Once the news broadcast is finished, the unit returns
to the previous mode\f
In some countries or regions, this service is not
available or the signal is too wea\b to be received\f
1\f News standby mode
.The news standby mode can be activated in
the FM or CD mode\f
.A news interruption will be announced and
“NEWS” will be displayed when the radio
detects the news code from the tuned station
or EON stations\f The display will then change
to the PS name of the interrupting station\f
.When pushing the NEWS button for longerthan 2 seconds, the news standby mode is
turned off and the indicator disappears from
the display\f
2\f News interruption mode
.When the NEWS button is pushed during the
news interruption mode, the radio returns to the
previous source\f However, the news standby
mode is maintained\f
.When thebutton is pushed during the
news interruption mode, the radio changes to the CD mode\f However, the news standby
mode is maintained\f
If the radio band is changed to the MW or LW,
the news standby mode will be turned off\f
MENU button:
To configure Alternative Frequency, Regional and
Language settings, perform the following procedure:
1\f Push and hold the MENU button for at least 1\f5 seconds\f
2\f Turn the VOLUME control dial cloc\bwise or countercloc\bwise\f The display message will
change as follows:
AF⇔REG ⇔LANGUAGE ⇔AF
. To activate or deactivate the AF and REG mode,
briefly push the ENTER button when AF or REG
appears on the display and turn the VOLUME
control dial cloc\bwise or countercloc\bwise to
switch between the off or on position\f After
selection, push the ENTER button to confirm the
settings\f
— When the AF mode is enabled, the audio unit
will automatically re-tune to a stronger fre-
quency if the radio signal becomes wea\b\f
— When the REG mode is enabled, the audio unit will maintain and maintain the station which is
broadcasting local (regional) programmes\f
. To change the display language, briefly push the
ENTER button when LANGUAGE appears on the
display then turn the MENU/VOL dial cloc\bwise or
countercloc\bwise to select the appropriate lan-
guage setting\f
ENGLISH ⇔DUTCH ⇔FRENCH ⇔SPANISH
⇔ GERMAN ⇔ITALIAN ⇔PORTUGUESE ⇔
ENGLISH
Heater and air conditioner, and audio system4-39
& R Q G L W L R Q