engine RENAULT PULSE 2012 1.G Manual PDF
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2012, Model line: PULSE, Model: RENAULT PULSE 2012 1.GPages: 352, PDF Size: 6.46 MB
Page 235 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
1. If the booster battery is in another vehicle*B,
\fosition the two vehicles*Aand*Bto bring the
batteries into close \fro\bimity to each other.
CAUTION:
If the battery of vehicle*Aequipped with the
Intelligent Key system is discharged, the ignition
switch cannot be moved from the “LOCK”
position and, if the steering lock is engaged,
the steering wheel cannot be moved. Connect
the jumper cables to the booster vehicle
*Bbefore turning the ignition switch and disenga-
ging the steering lock.
2. A\f\fly the \farking brake.
3. Automatic Transmission (AT)/Continuously Vari- able Transmission (CVT) model: Move the selector
lever to the “P” (Park) \fosition.
Manual Transmission (MT) model: Move the shift
lever to the “N” (Neutral) \fosition.
4. Switch off all unnecessary electrical systems (headlights, heater, air conditioner, etc.) .
5. Turn the ignition switch to the “LOCK” \fosition.
6. Remove the vent ca\fs, if equi\f\fed, on the battery.
7. Cover the battery with a firmly wrung out moist cloth to reduce the hazard of an e\b\flosion.
8. Connect the jum\fer cables in the sequence as illustrated (
*1,*2,*3,*4).
CAUTION:
.Always connect positive +to positive +and
negative 7to body ground, NOT to the
battery’s negative 7. .
Be sure that the jumper cables do not touch
moving parts in the engine compartment.
. Be sure that the jumper cable’s clamps do
not contact any other metal.
9. Start the engine of the booster vehicle
*Band let
it run for a few minutes.
10. De\fress the accelerator \fedal of the booster vehicle
*Bat about 2,000 r\fm.
11. Start the engine of the jum\fed vehicle
*Ain the
normal manner.
CAUTION:
. Never keep the starter motor engaged for
more than 10 seconds. If the engine does not
start right away, turn the ignition switch
“OFF” and wait at least 10 seconds before
trying again.
. If the starter motor does not start by pushing
the ignition switch, push the ignition switch
to the OFF position before trying again.
12. After the engine is started, carefully disconnect the jum\fer cables in the o\f\fosite sequence from
that illustrated (
*4,*3,*2,*1).
13. Remove and dis\fose of the cloth as it may be contaminated with corrosive acid.
14. Re\flace the vent ca\fs, if removed.
NOTE:
. For model with Stop/Start (Idling Stop)
System, use the special battery that is
enhanced in regard to the charge-discharge
capacity and life performance. Avoid using a
non-special battery for the Stop/Start (Idling
Stop) system, as this may cause early deterioration of the battery or a malfunction
of the Stop/Start (Idling Stop) system. For
the battery, it is recommended to use
Genuine RENAULT parts. For more informa-
tion, contact a RENAULT dealer.
. For model with Stop/Start (Idling Stop)
System, it may take some time until Stop/
Start (Idling Stop) System activates when
the battery is replaced or the battery term-
inal is disconnected for extended periods
and then reconnected.
In case of emergency6-9
& R Q G L W L R Q
Page 236 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
6-10In case of emergency
Do not attempt to start the engine by p\fshing the
vehicle\b
CAUTION:
.Automatic Transmission (AT)/Continuously
Variable Transmission (CVT) model cannot
be started by pushing. Attempting to do so
may cause damage to the transmission.
. Three-way catalyst equipped model should
not be started by pushing. Attempting to do
so may cause damage to the catalyst.
. Never try to start the engine by towing.
When the engine starts, the forward surge
could cause the vehicle to collide with the
towing vehicle.
. Stop/Start (Idling Stop) System equipped
model cannot be started by pushing the
vehicle.
WARNING:
.Never continue driving if your vehicle over-
heats. Doing so could cause a vehicle fire.
. Never open the hood if steam is coming out.
. Never remove the radiator cap while the
engine is hot. If the radiator cap is removed
when the engine is hot, pressurized hot
water will spurt out and possibly cause
burning, scalding or serious injury.
. If steam or coolant is coming from the
engine, stand clear of the vehicle to prevent
getting burned.
. Be careful not to allow your hands, hair,
jewelry or clothing to come into contact with,
or to get caught in the cooling fan or drive
belts. The engine cooling fan will start at any
time.
If yo\fr vehicle is overheating (indicated by the high
temperat\fre indicator) , or if yo\f feel a lack of engine
power, detect \fn\fs\fal noise, etc\b, take the following
steps:
1\b Safely move the vehicle off the road away from traffic\b
2\b T\frn on the hazard indicator flasher lights\b
3\b Apply the parking brake\b
4\b A\ftomatic Transmission (AT)/Contin\fo\fsly Vari- able Transmission (CVT) model: Move the selector
lever to the “P” (Park) position\b
Man\fal Transmission (MT) model: Move the shift
lever to the “N” (Ne\ftral) position\b
DO NOT STOP THE ENGINE . 5\b Open all windows\b
6\b T\frn off the air conditioner\b Set the temperat\fre
control to maxim\fm hot and fan control to
maxim\fm speed\b
7\b Get o\ft from the vehicle\b
8\b Vis\fally inspect and listen for steam or coolant escaping from the radiator before opening the
hood\b Wait \fntil no steam or coolant can be seen
before proceeding\b
9\b Open the engine hood\b
10\b Vis\fally inspect if the cooling fan is r\fnning\b
11\b Vis\fally inspect the radiator and radiator hoses for leakage\b
If the cooling fan is not r\fnning or the coolant is
leaking, stop the engine\b
12\b After the engine cools down, check the coolant level in the reservoir with the engine r\fnning\b Do
not open the radiator cap.
13\b Add coolant to the reservoir if necessary\b
Have yo\fr vehicle inspected/repaired at a RENAULT
dealer\b
PUSH STARTING IF YOUR VEHICLE OVERHEATS
& R Q G L W L R Q
Page 248 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
8-2Maintenance and do-it-yourself
Your new vehicle has been desi\fned to have minimum
maintenance requirements with lon\f service intervals
to save \bou both time and mone\b. However, some da\b-
to-da\b and re\fular maintenance is essential to maintain
\bour vehicle’s fine mechanical condition, as well as its
emission and en\fine performance.
It is the owner’s responsibilit\b to make sure that the
specified maintenance, as well as \feneral mainte-
nance, is performed.
As the vehicle owner, \bou are the onl\b one who can
ensure that \bour vehicle receives the proper main-
tenance care. You are a vital link in the maintenance
chain.
SCHEDULED MAINTENANCE
For \bour convenience, the required scheduled main-
tenance items are described and listed in a separate
maintenance booklet. You must refer to that booklet to
ensure that necessar\b maintenance is performed on
\bour vehicle at re\fular intervals.
GENERAL MAINTENANCE
General maintenance includes those items which
should be checked durin\f normal da\b-to-da\b operation
of the vehicle. The\b are essential if \bour vehicle is to
continue to operate properl\b. It is \bour responsibilit\b to
perform these procedures re\fularl\b as prescribed.
Performin\f \feneral maintenance checks requires
minimal mechanical skill and onl\b a few \feneral
automotive tools.
These checks and inspections can be done b\b
\bourself, a qualified technician, or if \bou prefer, a
RENAULT dealer.
WHERE TO GO FOR SERVICE
If maintenance service is required or \bour vehicle
appears to malfunction, have the s\bstems checked and
tuned b\b a RENAULT dealer.
RENAULT technicians are well-trained specialists and
are kept up-to-date with the latest service information
throu\fh technical bulletins, service tips, and internal
dealership trainin\f pro\frams. The\b are completel\b
qualified to work on RENAULT’s vehiclesbeforethe\b
work on \bour vehicle, rather than after the\b have
worked on it.
You can be confident that a RENAULT dealer’s service
department performs the best job to meet the
maintenance requirements on \bour vehicle — in a
reliable and economic wa\b. Durin\f normal da\b-to-da\b operation of the vehicle,
\feneral maintenance should be performed re\fularl\b as
prescribed in this section. If \bou detect an\b unusual
sounds, vibrations or smells, be sure to check for the
cause or have a RENAULT dealer do it promptl\b. In
addition, \bou should notif\b a RENAULT dealer if \bou
think that repairs are required.
When performin\f an\b checks or maintenance work,
closel\b observe “Maintenance precautions” (P.8-4) .
EXPLANATION OF GENERAL MAINTE-
NANCE ITEMS
Additional information on the following items
with
“*”is found later in this section.
Outside vehicle
The maintenance items listed here should be per-
formed from time to time, unless otherwise specified.
Doors and engine hood:
Check that all doors and the en\fine hood operate
properl\b. Also make sure that all latches lock securel\b.
Lubricate hin\fes and latches if necessar\b. Make sure
that the secondar\b latch of the en\fine hood keeps the
hood from openin\f when the primar\b latch is released.
When drivin\f in areas usin\f road salt or other
corrosive materials, check lubrication frequentl\b.
Lights*:
Clean the headli\fhts on a re\fular basis. Make sure that
the headli\fhts, stop li\fhts, tail li\fhts, turn si\fnal li\fhts,
and other li\fhts are all operatin\f properl\b and installed
securel\b. Also check the aim of the headli\fhts.
MAINTENANCE REQUIREMENTS GENERAL MAINTENANCE
& R Q G L W L R Q
Page 249 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
Tires*:
Check the pressure with a gauge often and alwa\fs
prior to long distance trips. If necessar\f, ad\bust the
pressure in all tires, including the spare, to the
pressure specified. Check carefull\f for damage, cuts
or excessive wear.
Tire rotation*:
Tires should be rotated ever\f 10,000 km (6,000
miles) . However, the timing for tire rotation ma\f var\f
according to \four driving habits and the road surface
conditions.
Wheel alignment and balance (for Europe):
If the vehicle should pull to either side while driving on
a straight and level road, or if \fou detect uneven or
abnormal tire wear, there ma\f be a need for wheel
alignment.
If the steering wheel or seat vibrates at normal highwa\f
speeds, wheel balancing ma\f be needed.
Windshield:
Clean the windshield on a regular basis. Check the
windshield at least ever\f six months for cracks or other
damage. Have a damaged windshield repaired b\f a
qualified repair facilit\f.
Wiper blades*:
Check for cracks or wear if the\f do not wipe properl\f.
Inside vehicle
The maintenance items listed here should be checked
on a regular basis, such as when performing periodic
maintenance, cleaning the vehicle, etc.Accelerator pedal:
Check the pedal for smooth operation and make sure
that the pedal does not catch or require uneven effort.
Keep the floor mats awa\f from the pedal.
Brake pedal*:
Check the pedal for smooth operation and make sure
that it has the proper distance under it when
depressed full\f. Check the brake booster function.
Keep the floor mats awa\f from the pedal.
Parking brake*:
Check that the pedal/lever has the proper distance of
travel.
Seat belts:
Check that all parts of the seat belt s\fstem (for
example, buckles, anchors, ad\busters and retractors)
operate properl\f and smoothl\f, and that the\f are
installed securel\f. Check the belt webbing for cuts,
fra\fing, wear or damage.
Steering wheel:
Check for changes in the steering conditions, such as
excessive free pla\f, hard steering or strange noises.
Warning lights and chimes:
Make sure that all warning lights and chimes are
operating properl\f.
Windshield defogger:
Check that the air comes out of the defogger outlets
properl\f and in good quantit\f when operating the
heater or air conditioner.
Windshield wiper and washer*:
Check that the wipers and washer operate properl\f
and that the wipers do not streak.
Under hood and vehicle
The maintenance items listed here should be checked
periodicall\f (for example, each time \fou check the
engine oil or refuel) .
Battery*:
Check the fluid level in each cell. It should be between
the UPPER and LOWER levels. Vehicles operated in
high temperatures or under severe conditions require
frequent checks of the batter\f fluid level.
Brake and clutch fluid level*:
Make sure that the brake and clutch fluid level is
between the MAX and MIN lines on the reservoir.
Engine coolant level*:
Check the coolant level when the engine is cold.
Engine drive belts*:
Make sure the drive belts are not fra\fed, worn, cracked
or oil\f.
Engine oil level*:
Check the level on the dipstick after parking the vehicle
on a level surface and turning off the engine.
Fluid leaks:
Check under the vehicle for fuel, oil, water or other fluid
leaks after the vehicle has been parked for a while.
Water dripping from the air conditioner after use is
normal. If \fou should notice an\f leaks or if fuel fumes
are evident, check for the cause and have it corrected
immediatel\f.
Maintenance and do-it-yourself8-3
& R Q G L W L R Q
Page 250 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
8-4Maintenance and do-it-yourself
Window washer fluid*:
Check that there is adequate fluid in the reser\foir.
M\bINTEN\bNCE PREC\bUTIONS
When performing any inspection or maintenance work
on your \fehicle, always take care to pre\fent serious
accidental injury to yourself or damage to the \fehicle.
The following are general precautions which should be
closely obser\fed.
WARNING:
.Park the vehicle on a level surface, apply the
parking brake securely and block the wheels
to prevent the vehicle from moving. Move
the selector lever to the “P”(Park) position
or the shift lever to the “N”(Neutral) position.
. Be sure the ignition switch is in the “OFF”or
“LOCK” position when performing any parts
replacement or repairs.
. Do not work under the hood while the
engine is hot. Always turn off the engine
and wait until it cools down.
. If you must work with the engine running,
keep your hands, clothing, hair and tools
away from moving fans, belts and any other
moving parts.
. It is advisable to secure or remove any loose
clothing and any jewelry, such as rings,
watches, etc. before working on your vehi-
cle.
. If you must run the engine in an enclosed
space such as a garage, be sure there is
proper ventilation for exhaust gases to
escape. .
Never get under the vehicle while it is
supported by a jack.
. Keep smoking materials, flame and sparks
away from fuel and the battery.
. Never connect or disconnect either the
battery or any transistorized component
connector while the ignition switch is in the
“ON” position.
. On gasoline engine models with the Multi-
port Fuel Injection (MFI) system, the fuel
filter and fuel lines should be serviced by a
RENAULT dealer because the fuel lines are
under high pressure even when the engine is
turned off.
. Your vehicle is equipped with an automatic
engine cooling fan. It may come on at any
time without warning, even if the ignition
switch is in the “OFF” position and the
engine is not running. To avoid injury, always
disconnect the negative battery cable before
working near the fan.
. Always wear eye protection whenever you
work on your vehicle.
. Never leave the engine or the transmission
related component harness connector dis-
connected while the ignition switch is in the
“ON” position.
. Avoid direct contact with used engine oil and
coolant. Improperly disposed engine oil,
engine coolant, and/or other vehicle fluids
can hurt the environment. Always conform to
local regulations for disposal of vehicle
fluids.
This “8. Maintenance and do-it-yourself” section
pro\fides instructions regarding only those items which are relati\fely easy for an owner to perform.
You should be aware that incomplete or improper
ser\ficing may result in operating difficulties or ex-
cessi\fe emissions, and could affect your warranty
co\ferage.
If in doubt about any servicing, have it
done by a RENAULT dealer.
& R Q G L W L R Q
Page 251 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
HR12DDR ENGINE MODEL
JVO0032X
1. B\fake a\bd clutch* fluid \fese\fvoi\f— Right-Ha\bd D\five (RHD) model
2. E\bgi\be d\five belts
3. E\bgi\be oil fille\f cap
4. Ai\f clea\be\f
5. B\fake a\bd clutch* fluid \fese\fvoi\f — Left-Ha\bd D\five (LHD) model 6. Fuse/fusible li\bk box
7. Wi\bdow washe\f fluid \fese\fvoi\f
8. E\bgi\be oil dipstick
9. Radiato\f cap
10. Batte\fy
11. E\bgi\be coola\bt \fese\fvoi\f
*: Fo\f Ma\bual T\fa\bsmissio\b (MT) Model
Maintenance and do-it-yourself8-5
ENGINE COMPARTMENT CHECK
LOCATIONS
& R Q G L W L R Q
Page 252 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
8-6Maintenance and do-it-yourself
HR12DE ENGINE MODEL
JVC011\fX
1. En\bine drive belts
2. Brake and clutch* fluid reservoir— Ri\bht-Hand Drive (RHD) model
3. En\bine oil filler cap
4. Air cleaner
5. Brake and clutch* fluid reservoir — Left-Hand Drive (LHD) model
6. Fuse/fusible link box \f. Window washer fluid reservoir
8. En\bine oil dipstick
9. Radiator cap
10. Battery
11. En\bine coolant reservoir
*: For Manual Transmission (MT) Model
& R Q G L W L R Q
Page 253 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
HR15DE ENGINE MODEL
JVC0118X
1. E\fgi\fe \brive belts
2. Brake a\f\b clutch* flui\b reservoir— Right-Ha\f\b Drive (RHD) mo\bel
3. E\fgi\fe oil filler cap
4. Air clea\fer
5. Brake a\f\b clutch* flui\b reservoir — Left-Ha\f\b Drive (LHD) mo\bel
6. Fuse/fusible li\fk box 7. Wi\f\bow washer flui\b reservoir
8. E\fgi\fe oil \bipstick
9. Ra\biator cap
10. Battery
11. E\fgi\fe coola\ft reservoir
*: For Ma\fual Tra\fsmissio\f (MT) Mo\bel
Maintenance and do-it-yourself8-7
& R Q G L W L R Q
Page 254 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
8-8Maintenance and do-it-yourself
K9K ENGINE MODEL
SDI2711
1. Br\fke \fn\b clutch flui\b reservoir
2. Air cle\fner
3. Fuse/Fusible link hol\bers
4. Priming pump
5. Win\bow w\fsher flui\b reservoir
6. Engine \brive belts
7. Engine oil filler c\fp
8. Engine oil \bipstick9. Engine cool\fnt reservoir
10. B\fttery
The l\fyout illustr\fte\b is for mo\bels equippe\b with \fn
engine cover.
WARNING:
. Never remove the radiator cap when the
engine is hot. Serious burns could be caused
by high-pressure fluid escaping from the
radiator. Wait until the engine and radiator
cool down.
. Engine coolant is poisonous and should be
stored carefully in marked containers out of
the reach of children.
The engine cooling system is fille\b \ft the f\fctory with \f
high-qu\flity, ye\fr-roun\b, \fnti-freeze cool\fnt solution.
The \fnti-freeze solution cont\fins rust \fn\b corrosion
inhibitors, therefore \f\b\bition\fl cooling system \f\b\bitives
\fre not necess\fry.
CAUTION:
. Never use any cooling system additives such
as radiator sealer. Additives may clog the
cooling system and cause damage to the
engine, transmission and/or cooling system.
. When adding or replacing coolant, be sure
to use only fluids approved by our technical
department with the proper mixture ratio.
Examples of the mixture ratio are shown
below:
ENGINE COOLING SYSTEM
& R Q G L W L R Q
Page 255 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
Outside temperaturedown to Composition
8C 8FEngine
coo\fant
(concentra- ted) \beminera-
\fized or dis- ti\f\fed water
í15 5 30% 70%
í35 í30 50% 50%
The use of other types of coo\fant so\futions may
damage the engine coo\fing system.
The radiator is equipped with a pressure cap. To
prevent engine damage, use on\fy a Genuine RENAULT
radiator cap or its equiva\fent when rep\facement is
required.CHECKING ENGINE COOLANT LEVEL
HR12\b\bR, HR12\bE and HR15\bE engine
mode\f
S\bI2571HR12DDR, HR12DE and HR15DE engineCheck the coo\fant \feve\f in the reservoir when the
engine is co\fd. If the coo\fant \feve\f is be\fow the MIN
\feve\f
*2, add coo\fant up to the MAX \feve\f*1. If the
reservoir is empty, check the coo\fant \feve\f in the
radiator when the engine is cold. If there is
insufficient coo\fant in the radiator, fi\f\f the radiator with
coo\fant up to the fi\f\fer opening and a\fso add it to the
reservoir up to the MAX \feve\f
*1.
If the cooling system frequently requires cool-
ant, have it checked by a RENAULT dealer.
K9K engine mode\f
S\bI2712K9K engineCheck the coo\fant \feve\f in the reservoir when the
engine is co\fd. If the coo\fant \feve\f is be\fow the MIN
\feve\f
*2, add coo\fant up to the MAX \feve\f*1.
If the cooling system frequently requires cool-
ant, have it checked by a RENAULT dealer.
CHANGING ENGINE COOLANT
Contact a RENAULT dea\fer if rep\facement is required.
Major engine coo\fing system repair shou\fd be per-
formed by a RENAULT dea\fer. The service procedures
can be found in the appropriate RENAULT Service
Manua\f.
Improper servicing can resu\ft in reduced heater
performance and engine overheating.
WARNING:
. To avoid being scalded, never change the
coolant when the engine is hot.
. Never remove the radiator cap when the
engine is hot. Serious burns could be caused
by high pressure fluid escaping from the
radiator.
Maintenance and do-it-yourself8-9
& R Q G L W L R Q