hood open RENAULT PULSE 2012 1.G Owners Manual


> (GLW    0RGHO .$2(0 B5HQDXOW @
2-18Instruments and controls
SPORT mode indicator \fight (i\b
equipped)
The SPORT mode indicator \fight i\f\fuminates when the
SPORT mode is turned “ON”. (See “Driving with
Continuous\fy Variab\fe Transmission (CVT)” (P.5-14)
\bor the use o\b the SPORT mode switch.)
Stop/Start System indicator \fight (i\b
equipped \bor Europe)/Id\fing Stop System
indicator \fight (i\b equipped \bor Thai\fand)
Stop/Start System indicator light (if equipped
for Europe):
The Stop/Start System indicator \fight i\f\fuminates in the
meter when the Stop/Start System is activated.
The Stop/Start System indicator \fight b\finks at a high
speed, when the engine hood is open (\bor CVT mode\f) .
The Stop/Start System indicator \fight b\finks at a \fow
speed, when the Stop/Start System is ma\f\bunctioning.
NOTE:
. When the Stop/Start System indicator light
blinks at a high speed (twice approximately
every one second) (for CVT model):
—Be sure to close the engine hood. When
the engine hood is open the engine will
be in the normal stopped state. In this
case, restart the engine with the ignition
switch.
. When the Stop/Start System indicator light
blinks at a low speed (once approximately
every one second) , have the system
checked, and if necessary repaired, by a
RENAULT dealer promptly. Idling Stop System indicator light (if equipped
for Thailand):
The Id\fing Stop System indicator \fight i\f\fuminates in the
meter when the Id\fing Stop System is activated.
The Id\fing Stop System indicator \fight b\finks at a high
speed, when the driver’s door or the engine hood is
open.
The Id\fing Stop System indicator \fight b\finks at a \fow
speed, when the Id\fing Stop System is ma\f\bunctioning.
NOTE:
.
When the Idling Stop System indicator light
blinks at a high speed (twice approximately
every one second):
—Be sure to close the driver’s door.
— Be sure to close the engine hood. When
the engine hood is opened the engine
will be in the normal stopped state. In this
case, restart the engine with the ignition
switch.
. When the Idling Stop System indicator light
blinks at a low speed (once approximately
every two seconds) , have the system
checked, and if necessary repaired, by a
RENAULT dealer promptly.
Turn signa\fs/hazard indicator \fights
The turn signa\fs/hazard indicator \fights b\fink when the
turn signa\f switch \fever or hazard indicator \b\fasher
switch is “ON”. (See “Head\fight and turn signa\f switch”
(P.2-29) or “Hazard indicator \b\fasher switch” (P.2-36) .)
Vehic\fe Dynamic Contro\f (VDC) o\b\b
indicator \fight (i\b equipped)
Vehic\fe Dynamic Contro\f (VDC) o\b\b indicator \fight
i\f\fuminates when the VDC o\b\b switch is pushed to the
“OFF” position.
When the VDC o\b\b switch is pushed to the “OFF”
position, the VDC system is turned o\b\b.
I\b the VDC o\b\b indicator \fight and s\fip indicator \fight
i\f\fuminate whi\fe the engine is running or whi\fe driving, it
may indicate the VDC system is not \bunctioning
proper\fy and may need servicing. Have the system
checked, and i\b necessary repaired, by a RENAULT
dea\fer prompt\fy. (See “Vehic\fe Dynamic Contro\f (VDC)
system (i\b equipped except \bor Europe)” (P.5-24) .)
AUDIBLE REMINDERS
Brake pad wear warning
The disc brake pads have audib\fe wear warnings.
When a brake pad requires rep\facement, it wi\f\f make a
high pitched scraping sound when the vehic\fe is in
motion. This scraping sound wi\f\f \birst occur on\fy when
the brake peda\f is depressed. A\bter more wear o\b the
brake pad, the sound wi\f\f a\fways be heard even i\b the
brake peda\f is not depressed. Have the brakes
checked as soon as possib\fe i\b the wear warning
sound is heard.
Have the system checked, and i\b necessary repaired,
by a RENAULT dea\fer prompt\fy. (See “Brakes” (P.8-
17) .)
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
Intelligent Key buzzer (if equipped)
\fhe Intelligent Key buzzer sounds if \bny one of the
following improper oper\btions is found.
.\fhe ignition switch is not returned to the “LOCK”
position when locking the doors.
. \fhe Intelligent Key is left inside the vehicle when
locking the doors.
. Any doors \bre not closed securely when locking
the doors.
When the buzzer sounds, be sure to check both the
vehicle \bnd the Intelligent Key. (See “Intelligent Key
system” (P.3-9) .)
Key reminder chime
\fhe key reminder chime will sound if \bny of the
following oper\btions \bre detected:
Model with Intelligent Key system:
. \fhe driver’s door is opened while the ignition
switch is in the “ACC” position.
Model without Intelligent Key system:
. \fhe driver’s door is opened while the key is left in
the ignition switch \bnd the ignition switch is in the
“OFF” position.
Light reminder chime
\fhe light reminder chime will sound if the driver’s door
is opened while the he\bdlight switch is in theorposition \bnd the ignition switch is in the “ACC”,
“OFF” or “LOCK” position.
Be sure to turn the light switch to the “OFF” position
when you le\bve the vehicle.
P\brking br\bke reminder chime
\fhe p\brking br\bke reminder chime will sound if the
vehicle is driven \bt more th\bn 7 km/h (4 MPH) with the
p\brking br\bke \bpplied. Stop the vehicle \bnd rele\bse the
p\brking br\bke.
Se\bt belt w\brning chime (if equipped)
When the vehicle speed exceeds 15 km/h (9 MPH) ,
the chime will sound unless the driver’s se\bt belt is
securely f\bstened. \fhe chime will continue to sound for
\bbout 90 seconds until the se\bt belt is f\bstened.
Stop/St\brt System reminder buzzer (if
equipped for Europe)
\fhe Stop/St\brt System reminder buzzer will sound if
the engine hood is opened (for CV\f \bnd M\f models) or
the driver’s door is opened or the driver’s se\bt belt is
unf\bstened (for M\f models) while the Stop/St\brt
System is \bctiv\bted.
NOTE:
. Be sure to close the engine hood. When the
engine hood is open, the engine will be in
the normal stopped state. In this case,
restart the engine with the ignition switch
(for CVT and MT models) .
. Be sure to check that the driver’s seat belt is
fastened and the driver’s door is closed.
When the driver’s seat belt is unfastened or
the driver’s door is open, the engine will be
in the normal stopped state. In this case,
restart the engine with the ignition switch
(for MT model) .
Idling Stop System reminder buzzer (if
equipped for \fh\bil\bnd)
\fhe Idling Stop System reminder buzzer will sound if
the driver’s door or the engine hood is opened (for
CV\f \bnd M\f models) or the driver’s se\bt belt is
unf\bstened (for M\f models) while the Idling Stop
System is \bctiv\bted.
NOTE:
.Be sure to close the driver’s door.
. Be sure to close the engine hood. When the
engine hood is open, the engine will be in
the normal stopped state. In this case,
restart the engine with the ignition switch.
Instruments and controls2-19
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
3 Pre-driving checks and adjustments
Keys ..................\(..................\(..........................\(..................\(..................\(........... 3-2Key ..................\(..................\(.....................\(..................\(..................\(........... 3-2
Anti-Theft System key (if e\fuipped\b ..................\(..................\(........ 3-2
Intelligent Key (if e\fuipped\b ..................\(..................\(....................... 3-3
Door locks ..................\(..................\(...............................\(..................\(............ 3-4 Super lock system (if e\fuipped\b ..................\(..................\(............... 3-4
Locking with key ..................\(..................\(...............................\(............. 3-5
Locking with inside lock knob ..................\(..................\(..................\(. 3-5
Locking with power door lock switch (if e\fuipped\b ................ 3-6
Vehicle speed sensing door lock mechanism (if e\fuipped\b .... 3-6
Auto door lock releasing mechanism (if e\fuipped\b ................. 3-6
Child safety rear door lock ..................\(..................\(..................\(....... 3-7
Remote keyless entry system (if e\fuipped\b ..................\(..................\(. 3-7 Using remote keyless entry system (if e\fuipped\b ..................\(.. 3-7
Intelligent Key system (if e\fuipped\b ..................\(..................\(............... 3-9 Operating range ..................\(..................\(...............................\(.......... 3-10
Using intelligent Key system ..................\(..................\(................... 3-10
Battery saver system ..................\(..................\(..................\(............... 3-12
Warning and audible reminders ..................\(..................\(............. 3-12
Trouble shooting guide ..................\(..................\(..................\(........... 3-13
Using remote keyless entry function ..................\(..................\(..... 3-15 Security system (if e\fuipped\b ..................\(..................\(..................\(.... 3-16
Theft warning system ..................\(..................\(..................\(........... 3-16
Anti-Theft System ..................\(..................\(..........................\(.......... 3-17
Hood ..................\(..................\(..................\(..................\(..................\(............. 3-18 Opening hood ..................\(..................\(..................\(..................\(...... 3-18
Closing hood ..................\(..................\(.....................\(..................\(..... 3-18
Back door ..................\(..................\(...............................\(..................\(......... 3-19 Opening back door ..................\(..................\(..................\(............... 3-19
Fuel filler lid ..................\(..................\(..................\(.......................\(.............. 3-19 Opening fuel filler lid ..................\(..................\(..................\(............ 3-19
Fuel filler cap ..................\(..................\(.....................\(..................\(..... 3-20
Steering wheel ..................\(..................\(..................\(..................\(.............. 3-20
Mirrors ..................\(..................\(.....................\(..................\(..................\(........ 3-20 Inside rearview mirror ..................\(..................\(..................\(........... 3-20
Outside rearview mirrors ..................\(..................\(....................... 3-21
Vanity mirrors (if e\fuipped\b ..................\(..................\(................... 3-23
Parking brake ..................\(..................\(..................\(............................\(...... 3-23 Lever type ..................\(..................\(..................\(..................\(.............. 3-23
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
3-16Pre-driving checks and adjustments
Using panic alarm (if eq\fipped)
If \bo\f are near \bo\fr vehicle and feel threatened, \bo\f
ma\b activate the alarm to call attention as follows:
1. P\fsh the “PANIC”
b\ftton*3on the
Intelligent Ke\b for more than 0.5 second.
2. The theft warning alarm will sta\b on for 25 seconds.
3. The panic alarm stops when:
. It has r\fn for 25 seconds, or
. An\b of the b\fttons on the Intelligent Ke\b are
p\fshed. (Note: Panic b\ftton sho\fld be p\fshed for
more than 0.5 second.)
Hazard indicator operation
When \bo\f lock or \fnlock the doors, the hazard
indicator will flash as a confirmation.
.“LOCK”: The hazard indicator flashes once.
. “UNLOCK”: The hazard indicator flashes twice. Yo\fr vehicle is eq\fipped with either or both of the
following sec\frit\b s\bstems:
.
Theft warning s\bstem
. Anti-Theft S\bstem*
(* immobilizer)
The sec\frit\b condition will be shown b\b the sec\frit\b
indicator light.
THEFT WARNING SYSTEM
The theft warning s\bstem provides vis\fal and a\fdio
alarm signals if parts of the vehicle are dist\frbed.
Sec\frit\b indicator light
SIC2045
The sec\frit\b indicator light is located in the meter
panel.
This light operates whenever the ignition switch is in
the “ACC”, “OFF” or “LOCK” position. This is normal.
How to activate the system:
1. Close all windows and p\fsh the ignition switch to the “OFF” position.
The system can be activated even if the
windows are open. 2. Carr\b the Intelligent Ke\b with \bo\f and get o\ft of
the vehicle.
3. Make s\fre the hood is closed. Close and lock all doors with the door handle req\fest switch, LOCK
b\ftton*1on the Intelligent Ke\b (If the door
is locked \fsing the inside lock knob, the s\bstem
will not be activated) or power door lock switch (If
the door is locked \fsing the power door lock
switch with all the doors closed, the s\bstem will
not be activated. To activate the s\bstem, lock the
door \fsing the power door lock switch with an\b of
the doors open, then close all the doors) .
4. Confirm that the sec\frit\b indicator light comes on. The sec\frit\b indicator light sta\bs on for approxi-
matel\b 30 seconds. The vehicle sec\frit\b s\bstem is
now pre-armed. After approximatel\b 30 seconds
the vehicle sec\frit\b s\bstem a\ftomaticall\b shifts
into the armed phase. The sec\frit\b light begins to
flash once ever\b approximatel\b 3 seconds.
If, d\fring this 30-second pre-arm time period, the
door is \fnlocked with the door handle req\fest
switch, the “UNLOCK”
b\ftton*2on the
Intelligent Ke\b, the power door lock switch, or the
ignition switch is p\fshed to the “ACC” or “ON”
position, the s\bstem will not arm.
Even when the driver and/or passengers are in
the vehicle, the system will activate with all
doors locked and ignition switch in the “LOCK”
position. Push the ignition switch to the “ACC” or
“ON” position to turn the system off.
Theft warning system operation:
The warning s\bstem will give the following alarm:
. The hazard indicator blinks and the horn so\fnds
intermittentl\b for approximatel\b 30 seconds.
SECURITY SYSTEM (if equipped)
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
.The alarm automatically turns off after approxi-
mately \f0 seconds. \bowever, the alarm reacti-
vates if the vehicle is tampered with again.
The alarm is activated by:
. Operating the door without using the Intelligent
Key system.
. Opening the hood.
How to stop alarm:
. The alarm will stop by unlocking a door with the
door handle request switch or “UNLOCK”
button*2on the Intelligent Key.
. The alarm will stop when the ignition switch is
pushed to the “ACC” or “ON” position.
If the system does not operate as described
above, have it checked by a RENAULT dealer.
ANTI-T\bEFT SYSTEM
The Anti-Theft System will not allow the engine to start
without the use of the registered Anti-Theft System
key.
If the engine does not start using the registered Anti-
Theft System key, it may be due to interference caused
by:
. Another Anti-Theft System key.
. Automated toll road device.
. Automated payment device.
. Other devices that transmit similar signals.
Start the engine using the following procedure:
1. Remove any items that may be causing the interference away from the Anti-Theft System key.
2. Leave the ignition switch in the “ON” position for approximately 5 seconds.
\f. Turn the ignition switch to the “OFF” or “LOCK” position, and wait approximately 10 seconds. 4. Repeat steps 2 and \f again.
5. Start the engine.
6. Repeat the steps above until all possible inter-
ferences are eliminated.
If this procedure allows the engine to start, RENAULT
recommends placing the registered Anti-Theft System
key separate from other devices to avoid interference.
FCC WARNING:
Changes or modifications not expressly ap-
proved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions; (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interference
that may cause undesired operation of the
device.
Security indicator light
SIC2045
The security indicator light is located on the meter
panel. It indicates the status of Anti-Theft System.
The light operates whenever the ignition switch is in the “LOCK”, “OFF” or “ACC” position. The security
indicator light indicates that the security systems on
the vehicle are operational.
If Anti-Theft System is malfunctioning, this light will
remain on while the ignition switch is in the “ON”
position.
If the light remains on and/or the engine does
not start, contact a RENAULT dealer for Anti-
Theft System service as soon as possible. Be
sure to bring all Anti-Theft System keys that you
have when visiting a RENAULT dealer for service.
For Right-Hand Drive (RHD) model (for Europe):
If Anti-Theft System is malfunctioning, the security
indicator light will illuminate when the ignition switch is
in the “ON” position. \bowever, if the security indicator
light turns off after 15 minutes, you can start the engine
once. See a RENAULT dealer for Anti-Theft System
service as soon as possible.
Pre-driving checks and adjustments\f-17
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
3-18Pre-driving checks and adjustments
WARNING:
.The hood must be closed and latched
securely before driving. Failure to do so
could cause the hood to fly open and result
in an accident.
. Never open the hood if steam or smoke is
coming from the engine compartment to
avoid injury.
OPENING HOOD
JVP0090X
1. Pu\f\f the h\b\bd \f\bck re\fease hand\fe*1\f\bcated
be\f\bw the instrument pane\f unti\f the h\b\bd springs
up.
2. L\bcate the \fever
*2in between the h\b\bd and
gri\f\fe and push the \fever sideways with y\bur
fingertips.
3. Raise the h\b\bd
*3.
4. Rem\bve the supp\brt r\bd
*4and insert it int\b the
s\f\bt*5.
Hold the coated parts
*Awhen removing or
resetting the support rod. Avoid direct contact
with the metal parts, as they may be hot
immediately after the engine has been stopped.
CLOSING HOOD
1. Whi\fe supp\brting the h\b\bd, return the supp\brt r\bd t\b its \brigina\f p\bsiti\bn.
2. S\f\bw\fy \f\bwer the h\b\bd t\b ab\but 20 t\b 30 cm (8 t\b 12 in) ab\bve the h\b\bd \f\bck, then \fet it dr\bp.
3. Make sure it is secure\fy \fatched.
CAUTION:
Before closing the hood, be sure to release the
support rod and store it in position. Otherwise,
the support rod will be damaged.
HOOD
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
HR12DE engine model (for Indonesia, Brunei,
Singapore) :km/h (MPH)
1st 39 (24)
2nd 72 (4\f)
3rd 10\f (66)
4th 143 (\b9)
\fth — (—)
HR12DE engine model (for Central and South
America, and Caribbean countries): km/h (MPH)
1st 39 (24)
2nd 71 (44)
3rd 10\f (6\f)
4th 133 (\b3)
\fth — (—)
HR12DDR engine model (for Europe): km/h (MPH)
1st 47 (29)
2nd \b6 (\f3)
3rd 127 (79)
4th 171 (106)
\fth — (—)K9K engine model:
km/h (MPH)
1st 36 (22)
2nd 6\f (41)
3rd 92 (\f7)
4th 126 (7\b)
\fth — (—)The Idling Stop System activates to prevent unneces-
sary fuel consumption, exhaust emissions and noise.
.
When you stop the vehicle, the engine is turned
off automatically.
. When you start the vehicle again, the engine is
turned on automatically.
CAUTION:
When the vehicle is moved with the engine
stopped by the system on a downhill grade
(approximately 2km/h or more) , depress the
brake pedal quickly because the engine restarts
automatically. This may lead to an accident.
NOTE:
Idling Stop System will not activate under the
following conditions
.when the engine is kept idling without any driving
after the engine is turned on.
. when the engine coolant temperature is low.
. when the battery capacity is low.
. when the battery temperature is low or extremely
high.
. when the vehicle is moved.
. when a negative pressure booster decreases.
. when the engine hood is opened with the engine
running.
. when the engine is turned on with the engine hood
open.
. when the steering wheel is operated.
. when Idling Stop System indicator blinks at a low
speed.
. when the accelerator pedal is depressed.
Starting and driving\f-19
IDLING STOP SYSTEM (if equipped
for Thailand)
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
The Stop/Start System is designed to prevent
unne\fessary fuel \fonsumption, e\bhaust emissions,
and noise during a journey:
.When the vehi\fle \fomes to rest the engine is
automati\fally stopped.
. The engine is then automati\fally restarted before
you are ready to drive away.
CAUTION:
At the end of the journey the engine must be
stopped and ignition switch be turned off. Lock
the vehicle as normal. Turning the ignition OFF
will shut down all electrical systems. Failure to
do this may result in a flat battery.
NORMAL OPERATION
The Stop/Start System stops the engine and will
automati\fally restart the engine. The Stop/Start
indi\fator light is shown in the meter.
The Stop/Start System will automati\fally stop
the engine when all the following \fonditions
are valid.
For MT model
.The shift lever is in Neutral position.
. The \flut\fh pedal is fully released.
. The vehi\fle speed is below about 2 km/h (1
MPH) .
. The driver’s seat belt is fastened.
. The Intelligent Key is in the vehi\fle.
. The driver’s door is \flosed.
For CVT model
. The sele\ftor lever is in the "D" (Drive) or "N"
(Neutral) position. .
The brake pedal is depressed.
. The vehi\fle is stopped.
. The driver’s seat belt is fastened.
. The driver’s door is \flosed.
NOTE:
The following conditions must also be satisfied
before the engine is automatically stopped. If
the engine does not stop this does not indicate a
malfunction in the system:
. The engine coolant temperature is at normal
operating levels.
. The vehicle has driven some distance since
engine start.
. The battery voltage and temperature are
within normal levels.
. The hood is closed.
. The steering wheel is not being turned.
. The system is not in front defogger mode.
(automatic air conditioner)
. The mode dial is not in front defogger mode.
(manual air conditioner)
. The rear window defogger is not operated.
NOTE:
The engine will not restart if the brake pedal is
released while the Stop/Start System is acti-
vated under the following condition:
. The selector lever is in the "P" (Park) position
(for CVT model) .
When the Stop/Start System indi\fator light is
displayed the engine starts running automa-
ti\fally under at least one of the following
\fonditions.
.The \flut\fh pedal is depressed (for MT model) .
. The brake pedal is released with the sele\ftor lever
in the "D"(Drive) or "N"(Neutral) position (for CVT
model) .
. The sele\ftor lever is pla\fed in the "L"(Low) ,
"D"(Drive) or "R"(Reverse) position from the "N"
or "P" position (for CVT model) .
. The driver’s seat belt is unfastened, or the driver’s
door is open (for CVT model) .
. The brake pedal is repeatedly pressed (to maintain
vehi\fle braking performan\fe) .
. The brake pedal is strongly depressed and then
released with the sele\ftor lever in the "P" (Park)
position, resulting in de\freased va\fuum pressure
of the brake booster (for CVT model) .
. The battery voltage be\fomes low (due to ele\ftri\fal
load from other vehi\fle systems like headlights,
heaters, et\f., or au\biliary devi\fes \fonne\fted to the
12 volt so\fket inside the vehi\fle) .
. The vehi\fle speed is above about 2 km/h (1
MPH) .
. The system is in front defogger mode. (automati\f
air \fonditioner)
. The mode dial is in front defogger mode. (manual
air \fonditioner)
. The rear window defogger is operated.
NOTE:
The following conditions will prevent the Stop/
Start System from automatically restarting the
engine. Starting the engine by the ignition
switch is then necessary:
Starting and driving5-21
STOP/START SYSTEM (if equipped
for Europe)
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
5-22Starting and driving
.The driver ’s seat belt is unfastened, or
driver’s door is open (for MT model) .
. The hood is open.
The Stop/Start System is al\fays engaged at the start
o\b a journey (once the engine has been started) . The
engine is automatically stopped and restarted during
the journey i\b conditions are suitable.
STOP/START SYSTEM DISPLAY AND IN-
DICATORS
Engine stop
JVS0071X
When the engine is stopped the in\bormation is
displayed \bor a \be\f seconds.
Vehicle information display: 1. Engine stop guidance
Instrument panel: 2. Stop/Start System indicator light
See “Vehicle in\bormation display” (P.2-20) about the
display. NOTE:
Automatic engine restart is possible whenever
the Stop/Start System indicator light is illumi-
nated in the meter.
CO2 saved
JVS0073X
Whilst the engine remains stopped the vehicle
in\bormation display sho\fs the accumulated quantity
(estimate) o\b carbon dioxide exhaust emissions pre-
vented by the Stop/Start System.
Vehicle information display:
1. CO2 saved in\bormation
Instrument panel: 2. Stop/Start System indicator light
. Push and hold the
button to reset the [CO2
Saved] value.
. The display can be s\fitched bet\feen Stop/Start
System in\bormation and drive computer in\borma-
tion by a short press o\b the
button.
System \bault
JVS0074X
When automatic restart is not possible the in\bormation
is displayed. The engine must be started by turning or
pushing the ignition s\fitch.
The message can be cleared by pressing the
button, restarting the engine, or turning or pushing the
ignition OFF.
Key LOCK \farning
JVS0081XType A
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
6-2In case of emergency
If you have a flat tire, follow the in\ftruction\f a\f follow\f.
S\bOPPING VEHICLE
WARNING:
.Be sure to apply the parking brake firmly.
. Be sure to move the shift lever to the “R”
(Reverse) position (Manual Transmission
(MT) model) .
. Be sure to move the selector lever to the “P”
(Park) position. (Automatic Transmission
(AT)/Continuously Variable Transmission
(CVT) model)
. Never change tires when the vehicle is on a
slope, ice or slippery area. This is hazardous.
. Never change tires when the oncoming
traffic is close to your vehicle. Call for
professional road assistance.
1. Safely move the vehicle off the road away from traffic.
2. \burn on the hazard indicator fla\fher light\f.
3. Park on a level \furface.
4. Apply the parking brake.
5. Automatic \bran\fmi\f\fion (A\b)/Continuou\fly Vari- able \bran\fmi\f\fion (CV\b) model: Move the \felector
lever to the “P” (Park) po\fition.
Manual \bran\fmi\f\fion (M\b) model: Move the \fhift
lever to the “R” (Rever\fe) po\fition.
6. \burn off the engine.
7. Open the hood and \fet up the warning triangle (if equipped):
.\bo warn other traffic.
.\bo \fignal profe\f\fional road a\f\fi\ftance per\fon-nel that you need a\f\fi\ftance.
8. Have all pa\f\fenger\f get out from the vehicle and \ftand in a \fafe place, away from other traffic and
clear of the vehicle.
PREPARING \bOOLS
SCE0902
Rai\fe the back door floor cover.
Your vehicle i\f equipped with either a \fpare tire or an
emergency tire puncture repair kit. Carefully read the
in\ftruction\f provided in the appropriate \fection. .
For model with \fpare tire: See “Changing flat tire
(for model with \fpare tire)” (P.6-2) .
. For model with emergency tire puncture repair kit:
See “Repairing flat tire (for model with emergency
tire puncture repair kit)” (P.6-5) .
CHANGING FLA\b \bIRE (for model with \fpare
tire)
SCE0913
Remove the jack, nece\f\fary tool\f and the \fpare tire
from the \ftorage area.
If \fpacer\f are equipped, remove them before removing
the \fpare tire.
Blocking wheel\f
MCE0001A
FLAT TIRE
&RQGLWLRQ