air condition RENAULT SCENIC 2006 J84 / 2.G Multimedia Nav 4R Owner's Manual

MULTIMEDIA
Fault finding - Interpretation of parameters86C
86C-55
NAV 4R
Program no.: 0000
Vdiag No.: 24
*RDS: Radio Data SystemPR010
RADIO FIELD INTENSITY
NOTESThere must be no present or stored faults.
Engine stopped, ignition on.
Tune to a known FM or AM station with the vehicle in an open area if possible.
The "Radio field intensity" corresponds to the electrical intensity of the radio signal (FM or AM) received at the
radionavigation tuner input, at the frequency currently selected. It is expressed in dB µV.
It gives an indication of the radio reception level. Below 18 dB µV, the station is considered weak and does not
appear in the list of radio stations.
A low value (< 18 dB µV) on this parameter means that:
–Either the selected station has a weak transmission in the geographical area. This may be due to the
distance from the selected station's transmitter (far from urban area, on motorways) or obstacles interfering
with the transmission of radio waves (mountainous areas, buildings, deep valleys).
–Or, if the reception conditions are good in the geographical area for the selected station, there is a fault on
the vehicle's reception system: one of the components (aerial/aerial amplifier/coaxial connection/radio aerial
connector) is faulty. In this case, refer to ALP 4.
This parameter may be used to compare two vehicles in order to determine if there actually is a vehicle fault.
Summary table of field values and their effect on radio reception:
Radio field intensityAudio
qualityRDS* decoding
(eg.: station names display)Automatic tuning/
Presence in the radio list
PR010 > 18 dBµVOK OK OK
14 dBµV < PR010 < 18 dBµVOK OKNOK
10 dBµV < PR010 < 14 dBµVOKNOK NOK
PR010 < 10 dBµVNOK NOK NOK
AFTER REPAIRRepeat the conformity check from the start.
NAV4R_V24_PR010

MULTIMEDIA
Fault finding - Dealing with commands
86C
86C-58
NAV 4R
Program no.: 0000
Vdiag No.: 24
AC004
SPEAKER TEST
NOTESThere must be no present or stored faults.
Special note:
A different bleep is emitted from each speaker.
Check that the "balance/fader" settings used are the default ones.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Check the condition and connection of the white 8-track connector of component 261 (Trafic: 662).
Also check the condition and connection of the faulty speaker connector.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
AFTER REPAIRCarry out another fault finding check on the system.

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-63
NAV 4R
Program no.: 0000
Vdiag No.: 24
Diagnostic - Fault finding chart
ALP 1 No dialogue possible between the computer and the CLIP tool
NOTESSwitch on the + after ignition feed to enter fault finding mode with the computer.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Note:
For Laguna, the system can only be switched on with the ignition on. The on/off
button does not operate with the ignition off.
Try the diagnostic tool on another vehicle.
Yes Is dialogue possible with a computer? No
On the faulty vehicle.
Check the battery voltage (see PR001 Battery
voltage).
Check the condition and connection of the battery
connections.
Check the condition of the fuses.
Check:
–the connection between the diagnostic tool and the
diagnostic probe (lead in good condition):
–the connection between the diagnostic lead and the
diagnostic socket (lead in good condition).
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP1

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-69
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 4 Poor radio reception
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Is the radio field intensity appropriate (see Interpretation of parameter PR010 Radio field
intensity)?Yes
No
Check the condition and connection of the connectors of component 261 (Trafic: 662) and
component 886.
Using the universal bornier, check the insulation, continuity and the absence of
interference resistance on the following connections:
●TB13 connection code.
●34AN connection code.
Between components 261 (commercial vehicle: 662) and 886.
Also check the feed to component 886 on connection 34AM (12 V ±± ± ±
1 V).
Are the connections faulty?
Yes No
If the connection or connections are faulty and there is a repair procedure
(see Technical Note 6015A, Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
Has the fault been solved?
Yes No
End of fault finding.
Contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP4

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-70
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 5 CD read fault
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Ensure there are no present or stored faults.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Is the fault related to CD reading by the radio/
navigation computer or by the 6CD changer?
By the radio/navigation computer By the 6CD changer
Is the CD an MP3 CD?
Yes
Check that component 261 (commercial vehicle:
662) is compatible with MP3 CDs (see "MP3" logo
on keypad).
Yes
Try with another MP3 CD.
Has the fault disappeared?
Yes
The faulty CD is in poor condition or is not
compatible (only MP3 format is compatible).
No
NoEnd of fault finding.
NoContact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP5

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-71
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 5
CONTINUED 1
Is the CD an audio CD?
Yes No
Try with another audio CD. Has the fault
disappeared?
Yes No
The faulty CD is in poor
condition or is not compatible.
The CD is not compatible - End of fault finding.
Contact the
Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-72
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 5
CONTINUED 2
Is the CD an audio CD?
Yes No
Try with another audio CD. Has the fault
disappeared?
Yes No
The faulty CD is in poor
condition or is not compatible.
Is the CD a cartographic map CD?
Yes No
Is the cartographic map CD
"Carminat Advanced
Navigation 2" compatible?
(original version).
Contact the
Techline.
The CD is not
compatible - End of
fault finding.
AFTER REPAIRCarry out a complete check with the diagnostic tool.

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-75
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 8The radio does not switch on automatically
or switches off after 20 minutes
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Ensure there are no present or stored faults.
Do not apply the following fault finding procedure to the Laguna II ph2.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Check the condition of the + 12 V ACC feed fuse of
component 261 (Trafic: 662).
To obtain the fuse value, see Wiring Diagrams
Technical Note or the value indicated on the fuse
box.
Does the radio come on?
No
Check for + accessories feed. To do this, refer to
the interpretation of status ET002 + 12 V
accessories feed.
Has the fault been solved?
No
Contact the Techline.
YesEnd of fault finding.
Yes
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP8

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-78
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 11 The 6 CD changer does not work
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Ensure there are no present or stored faults.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Disconnect then reconnect component 1272.
Does the CD changer request its code?
("CD 0000")
No
Check the condition and connection of the connector of components 261 (Trafic: 662) and 1272.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Has the fault been solved?
No
With the radio switched on, check for + battery feed
on connection 34BC and + accessories feed on
connection 34BD of the connector of
component 1272.
Are the + battery and + accessories feeds
present?
Yes
Contact the Techline.
YesRefer to ALP 10 The screen displays
"CD0000".
NoCheck the continuity, insulation and
the absence of interference resistance
on connections 34BC, 34BL and 34BD
between components 261 (Trafic: 662)
and 1272.
Yes Are the connections correct?
No
If the connection or connections are faulty and there is a
repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the
wiring, otherwise replace it.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP11