navigation RENAULT SCENIC 2006 J84 / 2.G Multimedia Nav 4R Owner's Guide

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-77
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 10 The screen displays "CD0000"
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Ensure there are no present or stored faults.
Is this message displayed following replacement
of the radio/navigation computer?
Yes
This message is displayed following replacement of
the radio/navigation computer. Enter the anti-theft
code from the old computer linked to the changer.
The changer registers the new computer's code.
If the old radio code is lost, the changer code can be
cleared using the clearing code.
To obtain the clearing code, contact the Techline.
It is necessary to enter the 6 CD changer
immobiliser code. To do this, follow the instructions
in Technical Note 5037A Code supply procedure.
NoThis message is displayed after the 6 CD
changer is replaced. The computer code
is programmed when the battery or
changer are connected.
When it is installed in the vehicle, the CD
changer is programmed with the radio
supply code.
Note:
The CD changer is supplied uncoded.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP10

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-81
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 14 Front panel button fault
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Check for + 12 V on connection SP2 and earth on connection MT (Laguna and Trafic), MAO (Mégane and
Scénic) or NL (Master) of component 261 (Trafic: 662).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that statuses ET026 Radio On/Off button, ET014 Source button, ET027 CD eject button, ET028 Tone
button, ET029 Voice synthesiser button, ET030 Station preselection button, ET032 Navigation button,
ET033 Directional button, ET034 Mode button, ET036 MUTE button, ET038 Front panel rotary button and
ET039 Front panel rotary button press are consistent during use (see Conformity check).
Do all the front panel buttons operate correctly?
No Yes
Check that no buttons are jammed.
If a button remains jammed, contact the Techline.
End of fault finding.
If the fault recurs, contact Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP14

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-82
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 15 No navigation voice messages
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Check that the sound from the radio is coming
through the front speakers.
Is the sound coming from the speakers?
Yes
Check that voice guidance is activated. Press the
NAV button.
Select the configuration then voice guidance
menus.
Is the "Voice messages" option active?
Yes
Check that the volume is correctly set.
In the AUDIO settings menu (Audio settings
button). Select the "volumes" then "NAV" menus
and press the + button on the satellite several
times to obtain at least volume 13.
Do your hear the: "+ loud" message?
Yes No
The fault is solved - customer
misunderstanding.
Cut the + accessories feed (for at least 1 minute) then
re-activate it
Is the fault still present?
NoApply ALP 12 No radio and/or
CD sound.
NoActivate the option.
End of fault finding.
In the event of an intermittent fault, contact
the Techline.
No
YesContact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP15