wiring RENAULT SCENIC 2006 J84 / 2.G Multimedia Nav 4R Owner's Guide

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-64
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 1
CONTINUED
Check component 225 on the vehicle:
–Check for + 12 V battery feed on connection BCP4 (Laguna), BP32 (Mégane and Scénic) or BP10 (commercial
vehicle), + 12 V after ignition feed on connection AP10 (Laguna), AP43 (Mégane and Scénic) or AP26
(commercial vehicle) and an earth on connections MA, MB and NAP (Laguna), NC and MK (LHD commercial
vehicle), NJ and MJ (RHD commercial vehicle), MAM and NAM (Scénic), MAM and NAM (RHD Mégane), MAN
and NAM (LHD Mégane), of component 225.
–Also check for + 12 V battery feed on connection BCP4 (commercial vehicle and Laguna) or BCP3 (Mégane
and Scénic) and an earth on connection MT (Trafic and Laguna), MAO (Mégane and Scénic) or NL (Master) of
the black 8-track connector of component 261 (Trafic: 662).
Using the universal bornier, check the insulation, continuity and the absence of interference resistance on
the following connections:
●connection code 107W,
●connection code 107X,
between components 261 and 225.
Trafic:
●connection code 34GA,
●connection code 34DZ,
between components 662 and 225.
Are these tests correct?
Yes No
If the fault has not been solved, contact Techline.
If the connection or connections are faulty and there is
a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a complete check with the diagnostic tool.

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-65
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 2 The screen stays black
NOTESOnly consult this ALP after a complete check with the diagnostic tool.
Check that the fault remains after pressing the on/off button for component 261 (Trafic:
662).
Use the Wiring Diagram Technical Note for the vehicle concerned.
Establish dialogue with the computer.
Is dialogue possible with the computer?
Yes
Check that the computer is correctly configured
(see Configuration and programming).
Yes
When the ignition is switched on, is the +
accessories feed present on connection SP2 of the
8-track connector of component 261 (Trafic: 662)?
Yes
NoApply ALP 1 No dialogue possible
between the computer and the CLIP
tool.
NoRun command VP005 Computer
configuration (see Configuration and
programming).
No
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP2

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-66
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 2
CONTINUED
Check that the radio display appears on the
instrument panel dot matrix display (only on
Mégane).
No Yes
Check for + 12 V on connections 46M and 46N
and earth on connections 46BG, 46BH and
46BK of the connector of component 1127.
Are these tests correct?
Yes
Cut the + accessories feed (for at least 1 minute)
then re-activate it.
Is the fault still present?If the connection is faulty and there is a
repair procedure (see Technical
Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair
the wiring, otherwise replace it.
No
NoEnd of fault finding.
In the event of an intermittent
fault, contact the Techline.
YesContact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-67
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 3 Poor guidance/poor location/GPS fault
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Place the vehicle in an open area for 10 minutes with the system switched on.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Is the GPS pictogram green?
Yes
Carry out a road test and check parameter PR002
Vehicle speed (see conformity check).
Has the fault been solved?
No
Check the conformity of parameter PR009 Angular
position (see Conformity check).
Has the fault been solved?
No
Carry out a road test to try to reproduce the fault
described by the customer.
Has the fault been reproduced?
No
Possible customer misunderstanding regarding system performance (eg.: location accuracy) or operation (eg.: use
of cartographic CD-ROM).
Refer to the Driver's Handbook.
No
YesEnd of fault finding.
YesEnd of fault finding.
Yes
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP3

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-69
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 4 Poor radio reception
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Is the radio field intensity appropriate (see Interpretation of parameter PR010 Radio field
intensity)?Yes
No
Check the condition and connection of the connectors of component 261 (Trafic: 662) and
component 886.
Using the universal bornier, check the insulation, continuity and the absence of
interference resistance on the following connections:
●TB13 connection code.
●34AN connection code.
Between components 261 (commercial vehicle: 662) and 886.
Also check the feed to component 886 on connection 34AM (12 V ±± ± ±
1 V).
Are the connections faulty?
Yes No
If the connection or connections are faulty and there is a repair procedure
(see Technical Note 6015A, Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
Has the fault been solved?
Yes No
End of fault finding.
Contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP4

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-70
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 5 CD read fault
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Ensure there are no present or stored faults.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Is the fault related to CD reading by the radio/
navigation computer or by the 6CD changer?
By the radio/navigation computer By the 6CD changer
Is the CD an MP3 CD?
Yes
Check that component 261 (commercial vehicle:
662) is compatible with MP3 CDs (see "MP3" logo
on keypad).
Yes
Try with another MP3 CD.
Has the fault disappeared?
Yes
The faulty CD is in poor condition or is not
compatible (only MP3 format is compatible).
No
NoEnd of fault finding.
NoContact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP5

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-73
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 6Stuck on message
Loading general map
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Check for the cartographic map CD in component 261 (commercial vehicle: 662).
After inserting the cartographic map CD in component 261 (commercial vehicle: 662), check that the general map
starts loading:
–message "Loading general map" displayed,
–display: (after 1 minute maximum) "progress percentage" pictogram (eg.: 35 %) in the lower status bar.
Note:
Loading may take up to 15 minutes.
Do not interrupt the loading process (by ejecting CD, switching off equipment, cutting + accessories feed,
etc.).
Loading is complete when the map appears.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP6

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-75
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 8The radio does not switch on automatically
or switches off after 20 minutes
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Ensure there are no present or stored faults.
Do not apply the following fault finding procedure to the Laguna II ph2.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Check the condition of the + 12 V ACC feed fuse of
component 261 (Trafic: 662).
To obtain the fuse value, see Wiring Diagrams
Technical Note or the value indicated on the fuse
box.
Does the radio come on?
No
Check for + accessories feed. To do this, refer to
the interpretation of status ET002 + 12 V
accessories feed.
Has the fault been solved?
No
Contact the Techline.
YesEnd of fault finding.
Yes
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP8

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-78
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 11 The 6 CD changer does not work
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Ensure there are no present or stored faults.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Disconnect then reconnect component 1272.
Does the CD changer request its code?
("CD 0000")
No
Check the condition and connection of the connector of components 261 (Trafic: 662) and 1272.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Has the fault been solved?
No
With the radio switched on, check for + battery feed
on connection 34BC and + accessories feed on
connection 34BD of the connector of
component 1272.
Are the + battery and + accessories feeds
present?
Yes
Contact the Techline.
YesRefer to ALP 10 The screen displays
"CD0000".
NoCheck the continuity, insulation and
the absence of interference resistance
on connections 34BC, 34BL and 34BD
between components 261 (Trafic: 662)
and 1272.
Yes Are the connections correct?
No
If the connection or connections are faulty and there is a
repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the
wiring, otherwise replace it.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP11

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-79
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 12 No radio and/or CD sound
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Ensure there are no present or stored faults.
Use the Wiring Diagram Technical Note for the vehicle concerned.
The message MUTE is displayed on the radio panel.
No
Check that status ET036 MUTE button displays
Released (see Conformity check).
Check the FADER setting:
In the AUDIO settings menu (Audio settings
button). Select the "audio" and "fader" menus;
Set the fader to "9 F 9" (for the test).
Has the fault been solved?
No
Run command AC004 Speaker test (see Dealing
with commands).
Has the fault been solved?
No Yes
Contact the Techline.
End of fault finding.
YesIs the vehicle equipped with PRETEL?
No Yes
Disconnect the radio/
telephone combined
control.
Has the fault been
solved?
No Yes
Check that the voltage on connection
107D (black ISOconnector)is0V.
Yes No
Contact the
Techline.
Check the radio/
telephone
combined control
If the connection is faulty and there is a repair
procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions
for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP12