battery RENAULT SCENIC 2006 J84 / 2.G Multimedia Nav 4R Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2006, Model line: SCENIC, Model: RENAULT SCENIC 2006 J84 / 2.GPages: 86, PDF Size: 0.29 MB
Page 6 of 86
MULTIMEDIA
Fault finding - Introduction
86C
86C-5
NAV 4R
Program no.: 0000
Vdiag No.: 24
5. FAULT FINDING LOG
You will always be asked for this log:
●when requesting technical assistance from the Techline,
●for approval requests when replacing parts for which approval is obligatory,
●to be attached to monitored parts for which reimbursement is requested. The log is needed for warranty
reimbursement, and enables better analysis of the parts removed.
6. SAFETY ADVICE
Safety rules must be observed during any work on a component to prevent any damage or injury:
–make sure that the battery is properly charged to avoid damaging the computers with a low load,
–use the appropriate tools. IMPORTANT!IMPORTANT
Any fault on a complex system requires thorough fault finding with the appropriate tools. The
FAULT FINDING LOG, which should be completed during the procedure, enables you to keep
track of the procedure which is carried out. It is an essential document when consulting the
manufacturer.
IT IS THEREFORE MANDATORY TO FILL OUT A FAULT FINDING LOG EACH TIME FAULT FINDING
IS CARRIED OUT
Page 30 of 86
MULTIMEDIA
Fault finding - Conformity check
86C
86C-29
NAV 4R
Program no.: 0000
Vdiag No.: 24
Fault finding - Conformity check
MAIN COMPUTER STATUSES AND PARAMETERS
NOTESOnly perform this conformity check after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine stopped, ignition on.
Order FunctionParameter / Status
checked or ActionDisplay and Notes Fault finding
1
Power supplyET001:+ 12 V after
ignition feedPRESENTIn the event of a fault, refer to
the interpretation of status
ET001 + 12 V after ignition
feed.
2ET002:+ 12 V
accessories
feedPRESENTIn the event of a fault, refer to
the interpretation of status
ET002 + 12 V accessories
feed.
3ET003:+ 12 V side
lights feedPRESENT
ABSENTIn the event of a fault, consult
the interpretation of status
ET003 + 12 V side lights
feed.
4PR001:Battery
voltage11 V < PR001 < 14 VIn the event of a fault, refer to
the interpretation of
parameter PR001 Battery
voltage.
5Vehicle
speedPR002:Vehicle
speedUnit: km/hIn the event of a fault, consult
the interpretation of
parameter PR002 Vehicle
speed.
6External
temperature
sensorPR006:External
temperaturePR006 = External
temperature sensor ±± ± ±
5 °° ° °
CIn the event of a fault, refer to
the interpretation of
parameter PR006 External
temperature.
7Angular
position
sensorPR009:Angular
positionUnit: *d/s
This parameter determines
The angular speed when
cornering.In the event of a fault, consult
the interpretation of
parameter PR009 Angular
position.
8Satellite
receptionPR008:Satellite
number
receivedIn an open area, the
number of satellites
received should be greater
than 3 for the system to
operate correctly.In the event of a fault, consult
the interpretation of
parameter PR008 Number of
satellites received.
9OffET004:RADIO ON
signalSTILL PRESENTIf the fault is still present,
contact Techline.
NAV4R_V24_CCONF
Page 47 of 86
MULTIMEDIA
Fault finding - Parameter summary table86C
86C-46
NAV 4R
Program no.: 0000
Vdiag No.: 24
Fault finding - Parameter summary table
Tool parameter Diagnostic tool title
PR001Battery voltage
PR002Vehicle speed
PR006External temperature
PR008Number of satellites received
PR009Angular position
PR010Radio field intensity
Page 48 of 86
MULTIMEDIA
Fault finding - Interpretation of parameters86C
86C-47
NAV 4R
Program no.: 0000
Vdiag No.: 24
Fault finding - Interpretation of parameters
PR001
BATTERY VOLTAGE
NOTESThere must be no present or stored faults.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Check the permanent + feed fuse of component 261 (Trafic: 662).
Check the condition of the connectors of components 710 (Laguna), 260 (Mégane II and Scénic) or
1016 (commercial vehicle) according to the location of the fuse.
If the voltage is at minimum:
Check the battery and the charge circuit (see Technical Note 6014A Checking the charge circuit).
If the voltage is at maximum:
Check that the charging voltage is correct with and without electrical consumers switched on.
AFTER REPAIRRepeat the conformity check from the start.
NAV4R_V24_PR001
Page 64 of 86
MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-63
NAV 4R
Program no.: 0000
Vdiag No.: 24
Diagnostic - Fault finding chart
ALP 1 No dialogue possible between the computer and the CLIP tool
NOTESSwitch on the + after ignition feed to enter fault finding mode with the computer.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Note:
For Laguna, the system can only be switched on with the ignition on. The on/off
button does not operate with the ignition off.
Try the diagnostic tool on another vehicle.
Yes Is dialogue possible with a computer? No
On the faulty vehicle.
Check the battery voltage (see PR001 Battery
voltage).
Check the condition and connection of the battery
connections.
Check the condition of the fuses.
Check:
–the connection between the diagnostic tool and the
diagnostic probe (lead in good condition):
–the connection between the diagnostic lead and the
diagnostic socket (lead in good condition).
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP1
Page 65 of 86
MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-64
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 1
CONTINUED
Check component 225 on the vehicle:
–Check for + 12 V battery feed on connection BCP4 (Laguna), BP32 (Mégane and Scénic) or BP10 (commercial
vehicle), + 12 V after ignition feed on connection AP10 (Laguna), AP43 (Mégane and Scénic) or AP26
(commercial vehicle) and an earth on connections MA, MB and NAP (Laguna), NC and MK (LHD commercial
vehicle), NJ and MJ (RHD commercial vehicle), MAM and NAM (Scénic), MAM and NAM (RHD Mégane), MAN
and NAM (LHD Mégane), of component 225.
–Also check for + 12 V battery feed on connection BCP4 (commercial vehicle and Laguna) or BCP3 (Mégane
and Scénic) and an earth on connection MT (Trafic and Laguna), MAO (Mégane and Scénic) or NL (Master) of
the black 8-track connector of component 261 (Trafic: 662).
Using the universal bornier, check the insulation, continuity and the absence of interference resistance on
the following connections:
●connection code 107W,
●connection code 107X,
between components 261 and 225.
Trafic:
●connection code 34GA,
●connection code 34DZ,
between components 662 and 225.
Are these tests correct?
Yes No
If the fault has not been solved, contact Techline.
If the connection or connections are faulty and there is
a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
Page 78 of 86
MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-77
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 10 The screen displays "CD0000"
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Ensure there are no present or stored faults.
Is this message displayed following replacement
of the radio/navigation computer?
Yes
This message is displayed following replacement of
the radio/navigation computer. Enter the anti-theft
code from the old computer linked to the changer.
The changer registers the new computer's code.
If the old radio code is lost, the changer code can be
cleared using the clearing code.
To obtain the clearing code, contact the Techline.
It is necessary to enter the 6 CD changer
immobiliser code. To do this, follow the instructions
in Technical Note 5037A Code supply procedure.
NoThis message is displayed after the 6 CD
changer is replaced. The computer code
is programmed when the battery or
changer are connected.
When it is installed in the vehicle, the CD
changer is programmed with the radio
supply code.
Note:
The CD changer is supplied uncoded.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP10
Page 79 of 86
MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-78
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 11 The 6 CD changer does not work
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Ensure there are no present or stored faults.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Disconnect then reconnect component 1272.
Does the CD changer request its code?
("CD 0000")
No
Check the condition and connection of the connector of components 261 (Trafic: 662) and 1272.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Has the fault been solved?
No
With the radio switched on, check for + battery feed
on connection 34BC and + accessories feed on
connection 34BD of the connector of
component 1272.
Are the + battery and + accessories feeds
present?
Yes
Contact the Techline.
YesRefer to ALP 10 The screen displays
"CD0000".
NoCheck the continuity, insulation and
the absence of interference resistance
on connections 34BC, 34BL and 34BD
between components 261 (Trafic: 662)
and 1272.
Yes Are the connections correct?
No
If the connection or connections are faulty and there is a
repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the
wiring, otherwise replace it.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP11