clutch RENAULT SCENIC 2009 J84 / 2.G Engine And Peripherals EDC16 User Guide

DIESEL INJECTION
Fault finding – Conformity check13B
13B - 167V3 MR-372-J84-13B250$540.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
CRUISE CONTROL/SPEED LIMITER (CONTINUED)
*ECU: Electronic control Unit
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test Conditions: ENGINE AT IDLE SPEED, COOLANT TEMPERATURE > 80 ˚C.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
3Brake contactET704:Brake switch No. 1- INACTIVE
- ACTIVE (brake
pedal depressed)In the event of a fault,
consult the interpretation
of status ET704 Brake
switch no. 1
4ET705: Brake switch No. 2- ACTIVE (brake
pedal released)
- INACTIVEIn the event of a fault,
consult the interpretation
of status ET705 Brake
switch no. 2
5Clutch pedal
switchET405:Clutch pedal switch- ACTIVE
- INACTIVEIn the event of a fault,
consult the interpretation
of status ET405 Clutch
switch.
6Cruise control
setpointPR130:Cruise control
setpointIndicates the
reference values
requested by the
driver (in mph (km/h))NONE
7Vehicle speedPR089:Vehicle speed0 mph
Gives the vehicle
speed in mph (km/h).
This parameter is
transmitted by the
ABS computer or
vehicle speed ECU*.
This signal is
transmitted to the
injection system on
the multiplex network.Test the multiplex
network. See fault finding
for the ABS system or the
vehicle speed ECU*.

DIESEL INJECTION
Fault finding – Conformity check13B
13B - 168V3 MR-372-J84-13B250$540.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
CRUISE CONTROL/SPEED LIMITER (continued 2)
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test Conditions: ENGINE AT IDLE SPEED, COOLANT TEMPERATURE > 80 ˚C.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
8Cruise control/
speed limiter
deactivationET415:Cruise control/speed
limiter
deactivationNONE: This status is
present on the diagnostic
tool when:
The computer has been
reinitialised.
The computer has been
reprogrammed.
- STATUS 1: Traction
control request
- STATUS 2: Brake pedal
depressed.
- STATUS 3: Clutch pedal
depressed.
- STATUS 4: Cancel
button pressed
- STATUS 5: Cruise
control or speed limiter
monitoring.
- STATUS 6: Gear lever
in neutral (manual
gearbox) or neutral
position (automatic
transmission).
- STATUS 7:
Inconsistency between
the request and the
vehicle speed.
- STATUS 8: Automatic
transmission in defect
mode.
- STATUS 9: Vehicle
speed monitoring.
- STATUS 10: Monitoring
by injection computer.In the event of a fault,
consult the
interpretation of status
ET415 Cruise control/
speed limiter
deactivation.

DIESEL INJECTION
Fault finding – Status summary table13B
13B - 171V3 MR-372-J84-13B250$585.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51DIESEL INJECTION
Fault finding – Status summary table
Tool status Diagnostic tool title
ET001+ After ignition computer feed
ET003Engine immobiliser
ET004Air conditioning authorisation
ET007Preheating unit control
ET014Monitor cooling fan 1
ET015Monitor cooling fan 2
ET021High speed fan assembly request
ET022Low speed fan assembly request
ET038Engine
ET042Cruise control/speed limiter
ET076Starting
ET077Impact detected
ET079Air conditioning present
ET088Compressor actuation request
ET104Injector code use
ET111Set number of passenger compartment heating resistors (RCH)
ET112Passenger compartment heating resistor cut-off
ET123Brake contact signal no. 2
ET233Clutch pedal
ET238Synchronisation
ET341Immobiliser code programmed
ET405Clutch pedal switch
ET415Deactivation of cruise control/speed limiter
ET589Electric coolant pump control (turbocharger)
ET651EGR programming cut-off
ET703Cruise control/speed limiter buttons
ET704Brake switch no. 1
ET705Brake switch no. 2
MR-372-J84-13B250$585.mif

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 193V3 MR-372-J84-13B250$630.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
- Check the condition and fitting of the clutch switch.
Check the continuity on the connection between track 1 of the clutch switch connector and track C4 of the black
32-track connector A of the injection computer.
Check for earth on track 2 of the clutch switch connector.
Repair if necessary.
- Remove the clutch switch and test its operation:
- Replace the switch if necessary.
- Check the condition and fitting of the clutch switch.
- Remove the clutch switch and test its operation:
- Replace the switch if necessary.
Check the earth insulation of the connection between track 1 of the clutch switch connector and track C4 of the
black 32-track connector A of the injection computer and repair if necessary. ET405
CLUTCH PEDAL SWITCH
NOTESSpecial notes:
Only apply the checks if the INACTIVE and ACTIVE statuses are not consistent with
the pedal position.
STATUS INACTIVE with clutch pedal depressed.
Continuity between tracks Insulation between tracks
Switch pressed
(Clutch pedal released)1 and 2
Switch released
(Clutch pedal depressed)1 and 2
STATUS ACTIVE with clutch pedal released.
Continuity between tracks Insulation between tracks
Switch pressed
(Clutch pedal released)1 and 2
Switch released
(Clutch pedal depressed)1 and 2
AFTER REPAIRSwitch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
EDC16_V51_ET405

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 195V3 MR-372-J84-13B250$630.mif
STATUS 3
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
ET415
1(CONTINUED)
STATUS 2
Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes STATUS 2 when driving with cruise control active (ET042
Cruise control/Speed limiter: CRUISE CONTROL) and the brake pedal is depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
“Fault memory”.
If status ET415 becomes STATUS 2 without pressing the brake pedal, consult the
interpretation of statuses ET704 and ET705 Brake contact No. 1 and No. 2.
Clutch pedal depressed
Manual gearbox ONLY
The cruise control function is deactivated when the gearbox is not coupled to the engine
(clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with cruise control active (ET042
Cruise control/speed limiter: CRUISE CONTROL) and the clutch pedal is depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
“Fault memory”.
If status ET415 becomes STATUS 3 without the clutch pedal being depressed, consult
the interpretation of status ET405: Clutch pedal.
If the vehicle is fitted with automatic transmission:
Test the multiplex network: check the configuration of the multiplex network in relation to
the vehicle's technical specification, especially the configuration of the automatic
transmission computer (see 88B, Multiplexing)
AFTER REPAIRSwitch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
1

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 197V3 MR-372-J84-13B250$630.mif
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
1
STATUS 7
ET415
(CONTINUED 3)
STATUS 6
Gear lever in neutral (manual gearbox) or the neutral position (automatic gearbox)
Status ET415 becomes STATUS 6, when driving with cruise control active (ET042:
Cruise control/speed limiter: CRUISE CONTROL) and:
- If the driver puts the gear lever in neutral position on a manual gearbox without
declutching or,
- if the gear lever is in neutral on an automatic gearbox.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
“Fault memory”.
If status ET415 becomes STATUS 6 without shifting the gear lever into neutral on a
manual gearbox without declutching, or into neutral on an automatic transmission, test
the ABS computer and check the configuration of the tyre size stored in the computer. If
the configuration is correct, contact the Techline.
Inconsistency between the request and the vehicle speed
Status ET415 becomes STATUS 7 if the computer detects too great a difference
between the speed requested by the driver and the vehicle speed.
This could occur when driving with cruise control active (ET042 Cruise control/ speed
limiter: CRUISE CONTROL) and when there is a significant difference.
This inconsistency deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ007
“Fault memory”.
If status ET415 changes to STATUS 7 where there is no significant difference in the
levels, contact the Techline.
AFTER REPAIRSwitch off the ignition and carry out a road test followed by a test with the diagnostic
tool.

DIESEL INJECTION
Fault finding – Interpretation of statuses13B
13B - 201V3 MR-372-J84-13B250$630.mif
STATUS 18
STATUS 20
STATUS 21
STATUS 11, 22
STATUS 8
STATUS 4, 17
STATUS 2
STATUS 3, 14, 16
STATUSES 1, 5, 6,
7, 9, 10, 12, 13, 15,
19, 23, 24
EDC16
PROGRAM NO.: C1
Vdiag No.: 51
ET651
EGR PROGRAMMING CUT-OFF
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
NONE
No EGR cut-off, the EGR valve is working properly in accordance with the
computer programs.
Switch off the ignition and wait 1 minute.
Switch the ignition on and check for faults.
Check the engine battery voltage with the engine stopped and then running.
If no faults are present or stored, restart the vehicle and test at idle speed.
Do not accelerate too much and reach an engine speed that is too high.
Accelerate above idling speed for a few seconds.
Check that the clutch pedal (ET405 Clutch pedal switch) is not pressed and that the
vehicle has stopped completely.
Test the present and stored faults and repair.
Reinitialise the EGR offsets by consulting the interpretation of command
SC036 Reinitialisation of programming and select EGR valve".
Allow the engine to heat up until this cut-off disappears.
Check that the regeneration of the particle filter in progress has completely finished.
Allow the engine to cool until this cut-off disappears.
Too low atmospheric pressure, the EGR valve is disabled.
AFTER REPAIRSwitch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
EDC16_V51_ET651

DIESEL INJECTION
Fault finding – Fault Finding Chart13B
13B -230V3 MR-372-J84-13B250$855.mif
EDC16
PROGRAM No.: C1
Vdiag No.: 51
ALP5 Irregular engine operation
NOTESBefore dealing with this customer complaint, check that there are no faults, and
the conformity (or otherwise) of the parameters and statuses using the
diagnostic tool.
If the customer complaint is not ironed out, perform the following checks:
If the engine races during gear changes, check, if there is a floor carpet, that this is not blocking the accelerator
pedal, the brake pedal or the clutch pedal, then check the conformity of the clutch switch and the conformity of the
accelerator pedal sensor when the pedal is released.
Measure the resistance of the engine speed sensor between terminals A and B of its black connector.
If the winding resistance is not between 510 Ω and 850 Ω at an engine temperature of 20˚C, replace the engine
speed sensor.
Check the continuity of the following connections:
–engine management computer, connector B track B1 track A of the engine speed sensor
–engine computer, connector B track C1 track B of the engine speed sensor
Check the conformity of the engine earths (oxidation, tightness, etc.).
Check the mounting, the air gap (check that the engine speed sensor - flywheel gap is 0.5 to 1.8 mm) and the
condition of the sensor (heating).
Replace if necessary.
Check the low pressure circuit.
–Check the pressure regulation solenoid valve by applying section B of the Rough idle fault finding chart.
~ 1600 bar with full load on the accelerator.
–Apply the procedure for checking the air flow; see conformity check.
–Check the turbocharger: apply test 9 Air line at the turbocharger, then test 5 Turbocharger control solenoid
valve check and test 6 Turbocharger.
–Apply the procedure for checking the hydraulic circuit see conformity check.
If the fault is still present:
–Check the balance of the cylinders using the CLIP Technic function, Compression test physical measurements
icon.
–Check the cylinder compressions if necessary using the special tool.
AFTER REPAIRcarry out a road test followed by a complete check with the diagnostic tool.
EDC16_V51_ALP5