check engine light RENAULT SCENIC 2010 J95 / 3.G Engine And Pheripherals DCM 1.2 Injection User Guide

13B-61
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$100.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF028
PRESENT
OR
STOREDCYLINDER 3 INJECTOR CONTROL CIRCUITC0: Open circuit
CC: Short circuit
1.DEF: At minimum stop
2.DEF: At maximum stop
NOTESConditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Special notes:
When fault DF028 occurs, the idle speed is locked at 1000 rpm, there is engine noise,
the engine speed is unstable, the engine performance is reduced to 75%, the level 1
warning light illuminates, and the message Check injector is displayed until the next
time the ignition is switched off.
See the Technical Note Wiring Diagrams for the vehicle.
C0 - CC
NOTESNone.
Switch off the ignition and wait 15 seconds.
Check the connection and condition of the cylinder 3 injector connector, component code 1954.
Check the connection and condition of connector B (48-track) of the injection computer, component code 120.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Run command AC007 Cylinder 3 injector.
If injector 3 cannot be heard operating five times in a cycle, connect the wire of the cylinder 4 injector to
the cylinder 3 injector and run command AC008 Cylinder 4 injector.
Does this injector actuation cycle work?
Note:
If the wires cannot be swapped, continue the procedure by replying YES to the previous question.
DCM1.2_V48_DF028/DCM1.2_V4C_DF028/DCM1.2_V50_DF028/DCM1.2_V54_DF028/DCM1.2_V58_DF028/DCM1.2_V5C_DF028

13B-64
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$100.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF029
PRESENT
OR
STOREDINJECTOR CYLINDER 4 CONTROL CIRCUITC0: Open circuit
CC: Short circuit
1.DEF: At minimum limit
2.DEF: At maximum limit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Special notes:
When fault DF029 occurs, the idle speed is locked at 1000 rpm, there is engine noise,
the engine speed is unstable, the engine performance is reduced to 75%, the level 1
warning light illuminates, and the message Check injector is displayed until the next
time the ignition is switched off.
See the Technical Note Wiring Diagrams for the vehicle.
C0 - CC
NOTESNone.
Switch off the ignition and wait 15 seconds.
Check the connection and condition of the cylinder 4 injector connector, component code 196.
Check the connection and condition of connector B (48-track) of the injection computer, component code 120.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Run command AC008 Cylinder 4 injector.
If injector 4 cannot be heard operating five times in a cycle, connect the wire of the cylinder 3 injector to
the cylinder 4 injector and use command AC007 Cylinder 3 injector.
Does this injector actuation cycle work?
Note:
If the wires cannot be swapped, continue the procedure by replying YES to the previous question.
DCM1.2_V48_DF029/DCM1.2_V4C_DF029/DCM1.2_V50_DF029/DCM1.2_V54_DF029/DCM1.2_V58_DF029/DCM1.2_V5C_DF029

13B-72
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$100.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
* C2I: Individual injector correction
DF038
PRESENT
OR
STOREDCOMPUTER1.DEF: Analogue - digital converter
2.DEF: Enter injector codes
3.DEF: Memory self-test
4.DEF: Watchdog not refreshed
5.DEF: Interference on the injector control line
6.DEF: Watchdog activation
NOTESSpecial notes:
When this fault appears:
either: the engine speed is locked at 1300 rpm, the engine is noisy, and the level 1
warning light illuminates with the message Check injection displayed on the
instrument panel,
or: the engine stops and the level 2 warning light illuminates with the message Faulty
injection displayed on the instrument panel.
See the Technical Note Wiring Diagrams for the vehicle.
1.DEF
3.DEF
4.DEF
6.DEF
NOTESNone.
Contact Techline.
2.DEF
NOTESNone.
Check that the individual injector correction (C2I*) matches the injectors; if not, enter the C2I*
(see Configurations and programming).
If the C2I* does match the injectors, contact the Techline.
DCM1.2_V48_DF038/DCM1.2_V4C_DF038/DCM1.2_V50_DF038/DCM1.2_V54_DF038/DCM1.2_V58_DF038/DCM1.2_V5C_DF038

13B-74
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$110.mif
13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF039
PRESENT
OR
STOREDINLET AIR TEMPERATURE SENSOR CIRCUIT
CO.1: Open circuit or short circuit to +12 V
CC.0: Short circuit to earth
NOTESSpecial notes:
When this fault arises, the engine is noisy and a light smoke appears.
See the Technical Note Wiring Diagrams for the vehicle.
IMPORTANT
The Inlet air temperature sensor is absent when the engine is fitted with a flow sensor. In this case, its value is not
a true representation and is fixed on the following engines: K9K766, K9K724 in Vdiag 4C and 50.
It will always be absent on K9K 766, 768, 724 in Vdiag 48, as well as on K9K 768 Vdiag 4C and 50.
ENGINE: K9K 750
Move the wiring between the computer, component code 120 and the injection air temperature and pressure
sensor, component code 1474 to see if the status changes (present stored).
Look for any wiring damage and check the connection and condition of the inlet air temperature and pressure
sensor, component code 1474 and its connections.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
If the resistance of the air temperature sensor is not:
15614 Ω ± 828 Ω at -20
°C
5887 Ω ± 283 Ω at 0
°C
2511 Ω ± 108 Ω at 20
°C
1200 Ω ± 47 Ω at 40
°C
612 Ω ± 22 Ω at 60
°C,
replace the air temperature sensor.
Check the insulation and continuity of the following connections:
–3KQ between components 1474 and 120,
–3LQ between components 1474 and 120,
–3LN between components 1474 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, replace the inlet air temperature and pressure sensor, component code 1474.
If the fault is still present, contact the Techline.
DCM1.2_V48_DF039/DCM1.2_V4C_DF039/DCM1.2_V50_DF039/DCM1.2_V54_DF039/DCM1.2_V58_DF039/DCM1.2_V5C_DF039
DIESEL INJECTION
Fault finding – Interpretation of faults

13B-83
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF052
PRESENT
OR
STOREDINJECTORS CONTROL CIRCUIT
CC.1: short circuit to +12 volts.
CC.0: short circuit to earth
NOTESPriorities when dealing with a number of faults:
–DF026 Cylinder 1 injector control circuit,
–DF027 Cylinder 2 injector control circuit,
–DF028 Cylinder 3 injector control circuit,
–DF029 Cylinder 4 injector control circuit,
the fault finding procedure remains the same, but the combination of faults makes it
possible to identify the defective injector(s).
Special notes:
When the fault occurs: there is engine noise, the engine speed is unstable, the engine
performance is reduced, and the level 2 warning light comes on with the message
Faulty injection displayed on the instrument panel.
See the Technical Note Wiring Diagrams for the vehicle.
Switch off the ignition, check the condition and connection of the injector connectors, component codes 193,
194, 195, and 196.
If the connector(s) are faulty and there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the connector(s), otherwise replace the wiring.
Switch off the ignition, disconnect the injectors (or the injector identified by faults DF026 Cylinder 1 injector
control circuit, DF027 Cylinder 2 injector control circuit, DF028 Cylinder 3 injector control circuit,
DF029 Cylinder 4 injector control circuit) and switch on the ignition again.
Using the diagnostic tool, check for changes to fault DF052.
Is DF052 present or stored?
DCM1.2_V48_DF052/DCM1.2_V4C_DF052/DCM1.2_V50_DF052/DCM1.2_V54_DF052/DCM1.2_V58_DF052/DCM1.2_V5C_DF052

13B-85
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF053
PRESENT
OR
STOREDRAIL PRESSURE REGULATION FUNCTION
1.DEF: at minimum stop
2.DEF: at maximum stop
3.DEF: below minimum threshold
4.DEF: above maximum threshold
5.DEF: high flow current < minimum
6.DEF: high flow current > maximum
7.DEF: low flow current < minimum
8.DEF: low flow current > maximum
NOTESPriorities when dealing with a number of faults:
–DF098 Fuel temperature sensor circuit,
–DF007 Rail pressure sensor circuit.
Special note. If DF053, the engine may stop with the level 2 warning light illuminated
with the message Faulty injection displayed on the instrument panel.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine running.
See the Technical Note Wiring Diagrams for the vehicle.
Check the presence and conformity of the fuel, run TEST 13: Diesel fuel conformity check.
Check the connection and condition of the flow actuator connector, component code 1105.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for + 12 V (after relay) on connection 3FB1 or 3FB2 (for New Twingo) or 3FB3 (for Kangoo 2) of
component 1105.
Check the connection and condition of connector B (brown 48-track) of the injection computer, component
code 120.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance between connections 3HI and 3FB1 or 3FB2 (for New Twingo) or 3FB3 (for Kangoo 2)
of component 1105.
If the resistance of the flow actuator is not between 4.8 Ω and 5.8 Ω at 20
°C, replace the flow actuator, component
code 1105 (see MR 364 (Mégane II), MR 370 (Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411
(New Twingo), MR 417 (Kangoo 2), Mechanical, 13B, Diesel injection, Flow actuator: Removal - Refitting).
DCM1.2_V48_DF053/DCM1.2_V4C_DF053/DCM1.2_V50_DF053/DCM1.2_V54_DF053/DCM1.2_V58_DF053/DCM1.2_V5C_DF053

13B-90
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF059
PRESENT
OR
STOREDCOMBUSTION MISFIRES ON CYLINDER 1
NOTESSpecial notes:
If fault DF059 is present: there is engine noise and jerking, the engine runs on three
cylinders, the engine speed is held at 1000 rpm, the engine performance is reduced to
75%, and the level 1 warning light illuminates.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Priorities when dealing with a number of faults:
–DF026 Cylinder 1 injector control circuit (CC or CO),
–DF053 Rail pressure regulation function.
Check the presence and conformity of the fuel. Run TEST 13: Diesel fuel conformity check.
Run TEST 3 Injector check.
Run TEST 7 High pressure circuit sealing check.
Check the engine compression.
Repair if necessary.
Check the valve clearance and adjust if necessary.
Check the inlet ducts, as well as the EGR valve, and clean them if necessary (see Technical Note 3916 Cleaning
the EGR solenoid valve).
If the fault is still present, replace the injector, component code 193 (see MR 364 (Mégane II), MR 370 (Scénic II),
MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2), Mechanical, 13B, Diesel
injection, Diesel injector: Removal - Refitting).
DCM1.2_V48_DF059/DCM1.2_V4C_DF059/DCM1.2_V50_DF059/DCM1.2_V54_DF059/DCM1.2_V58_DF059/DCM1.2_V5C_DF059

13B-91
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF060
PRESENT
OR
STOREDMISFIRING ON CYLINDER 2
NOTESSpecial notes:
If fault DF060 is present: there is engine noise and jerking, the engine runs on three
cylinders, the engine speed is held at 1000 rpm, the engine performance is reduced to
75%, and the level 1 warning light illuminates.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Priorities when dealing with a number of faults:
–DF027 Cylinder 2 injector control circuit (CC or CO),
–DF053 Rail pressure regulation function.
Check the presence and conformity of the fuel. Run TEST 13: Diesel fuel conformity check.
Run TEST 3 Injector check.
Run TEST 7 High pressure circuit sealing check.
Check the engine compression.
Repair if necessary.
Check the valve clearance and adjust if necessary.
Check the inlet ducts, as well as the EGR valve, and clean them if necessary (see Technical Note 3916 Cleaning
the EGR solenoid valve).
If the fault is still present, replace the injector, component code 194 (see MR 364 (Mégane II), MR 370 (Scénic II),
MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2), Mechanical, 13B, Diesel
injection, Diesel injector: Removal - Refitting).
DCM1.2_V48_DF060/DCM1.2_V4C_DF060/DCM1.2_V50_DF060/DCM1.2_V54_DF060/DCM1.2_V58_DF060/DCM1.2_V5C_DF060

13B-92
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF061
PRESENT
OR
STOREDMISFIRING ON CYLINDER 3
NOTESSpecial notes:
If fault DF061 is present: there is engine noise and jerking, the engine runs on three
cylinders, the engine speed is held at 1000 rpm, the engine performance is reduced to
75%, and the level 1 warning light illuminates.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Priorities when dealing with a number of faults:
–DF028 Cylinder 3 injector control circuit (CC or CO),
–DF053 Rail pressure regulation function.
Check the presence and conformity of the fuel. Run TEST 13: Diesel fuel conformity check.
Run TEST 3 Injector check.
Run TEST 7 High pressure circuit sealing check.
Check the engine compression.
Repair if necessary.
Check the valve clearance and adjust if necessary.
Check the inlet ducts, as well as the EGR valve, and clean them if necessary (see Technical Note 3916 Cleaning
the EGR solenoid valve).
If the fault is still present, replace the injector, component code 195 (see MR 364 (Mégane II), MR 370 (Scénic II),
MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2), Mechanical, 13B, Diesel
injection, Diesel injector: Removal - Refitting).
DCM1.2_V48_DF061/DCM1.2_V4C_DF061/DCM1.2_V50_DF061/DCM1.2_V54_DF061/DCM1.2_V58_DF061/DCM1.2_V5C_DF061

13B-93
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V10 MR-372-J84-13B100$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF062
PRESENT
OR
STOREDMISFIRING ON CYLINDER 4
NOTESSpecial notes:
If fault DF062 is present: there is engine noise and jerking, the engine runs on three
cylinders, the engine speed is held at 1000 rpm, the engine performance is reduced to
75%, and the level 1 warning light illuminates.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Priorities when dealing with a number of faults:
–DF029 Cylinder 4 injector control circuit (CC or CO),
–DF053 Rail pressure regulation function.
Check the presence and conformity of the fuel. Run TEST 13: Diesel fuel conformity check.
Run TEST 3 Injector check.
Run TEST 7 High pressure circuit sealing check.
Check the engine compression.
Repair if necessary.
Check the valve clearance and adjust if necessary.
Check the inlet ducts, as well as the EGR valve, and clean them if necessary (see Technical Note 3916 Cleaning
the EGR solenoid valve).
If the fault is still present, replace the injector, component code 196 (see MR 364 (Mégane II), MR 370 (Scénic II),
MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2), Mechanical, 13B, Diesel
injection, Diesel injector: Removal - Refitting).
DCM1.2_V48_DF062/DCM1.2_V4C_DF062/DCM1.2_V50_DF062/DCM1.2_V54_DF062/DCM1.2_V58_DF062/DCM1.2_V5C_DF062