heating RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Injection User Guide

13B-46
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF017
PRESENT
OR
STOREDPRE-POSTHEATING UNIT CONTROL CIRCUIT
CC.1 : short circuit to + 12 V
CC.0 : open circuit or short circuit to earth
CO : open circuit
1.DEF : internal electrical fault
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after actuator command AC001 Preheating unit, or after
an attempted engine start.
Special notes:
If the fault is present, it is difficult or even impossible to start the vehicle when cold.
Use bornier Elé. 1681 for all operations on the injection computer connectors.
CC.1
NOTESNone.
Check the pre-postheating unit connections and the heating plug supply cables.
Check the injection computer connections.
Repair if necessary.
Check the condition of the F2 (70A) supply fuse on the power supply fuse board.
Check the continuity and insulation against + 12 V of the following connections:
Injection computer grey 32-track connector C, track E2 Track 8 preheating unit
Injection computer grey 32-track connector C, track A4 Track 3 preheating unit
Repair if necessary.
If the fault is still present, replace the pre-postheating unit.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF017/EDC16_V48_DF017/EDC16_V4C_DF017

13B-47
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF017
CONTINUED
CC.0
CO
NOTESSpecial notes:
If the pre-postheating unit has a short circuit to earth there is
a risk that the heater plugs will be operated continuously.
The heater plugs and the engine may be damaged.
Check the pre-postheating unit connections and the heating plug supply cables.
Check the injection computer connections.
Repair if necessary.
Check the condition of the F2 (70A) supply fuse on the power supply fuse board.
Check the continuity and insulation against earth of the following connection:
Injection computer grey 32-track connector C, track A4 Track 3 preheating unit
Injection computer grey 32-track connector C, track E2 Track 8 preheating unit
Repair if necessary.
If the fault is still present, replace the pre-postheating unit.
1.DEF
NOTESNone.
Check the pre-postheating unit connections and the heating plug supply cables.
Check the injection computer connections.
Repair if necessary.
Check the condition of the F2 (70A) supply fuse on the power supply fuse board.
Check for continuity and the absence of interference resistance on the following connection:
Injection computer grey 32-track connector C, track E2 Track 8 preheating unit
Repair if necessary.
If the fault is still present, check that the computer output is working correctly.
with the pre-postheating unit connected:
– connect the negative terminal of the voltmeter to track 8 of the preheating unit,
– connect the positive terminal of the voltmeter to the + 12 V battery,
– run command AC001 Pre-postheating unit.
If the voltmeter does not indicate the battery voltage while the command is running (ten one-second ON/OFF
cycles), contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.

13B-48
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF025
PRESENT
OR
STOREDPRE-POSTHEATING UNIT DIAGNOSTIC LINE
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after several attempts to start the engine, or following
actuator command AC001 Preheating unit.
Special notes:
It is difficult or even impossible to start the engine when cold.
Use bornier Elé. 1681 for all operations on the injection computer connectors.
Check the pre-postheating unit connections.
Check the connections on all the heater plugs.
Repair if necessary.
Check the resistance of the heater plugs:
Replace any plug whose resistance is not below 2Ω at + 20°C.
Check the continuity and absence of interference resistance of the following connections:
– Preheating unit track 1 Heater plug of cylinder 3
– Preheating unit track 2 Heater plug of cylinder 4
– Preheating unit track 6Heater plug of cylinder 1
– Preheating unit track 7 Heater plug of cylinder 2
Check for the presence of +12V battery on track 3 of the preheating relay (via maxi fuse).
Check the engine earthing.
If the fault is still present,
Check the injection computer connections.
Check for continuity and the absence of interference resistance on the following connection:
Injection computer, grey 32-track connector C, track A4 Track 9 preheating unit connector
If the fault is still present, replace the pre-postheating unit.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF025/EDC16_V48_DF025/EDC16_V4C_DF025

13B-85
DIESEL INJECTION
Fault finding - Interpretation of faults
13B
V10 MR-372-J84-13B150$376.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF097
PRESENT
OR
STOREDCAMSHAFT SENSOR CIRCUIT
1.DEF : no signal
2.DEF : inconsistent signal
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault declared present before an attempt is made to start the engine it will not be
possible to start the engine.
Use bornier Ele. 1681 for all operations on the injection computer connectors.
1.DEF
2.DEF
NOTESPriority when dealing with a number of faults:
In the event of more than one fault:
–DF056 Air flow sensor circuit,
–DF057 Water in diesel fuel detector circuit,
–DF067 Damper control circuit,
Check the conformity of the + 12 V after relay supply line,
from track 2 of the UPC PPM1 connector.
(Use the Wiring Diagrams Technical Note for the vehicle).
Check the camshaft sensor connectors,
Check the injection computer connections.
Check that the camshaft sensor is correctly positioned and mounted.
Also check the general condition (damaged housing, heating up, etc.).
Carry out the necessary repairs.
Check the continuity and absence of interference resistance of the following connections:
Injection computer brown 48-track connector B, track D1 Track 2 Camshaft sensor
Injection computer brown 48-track connector B, track A1 Track 1 Camshaft sensor
Repair if necessary.
Check the camshaft sensor resistance between tracks 2 and 3.
If the resistance is not 10250Ω ±500 at 20°C, replace the sensor.
AFTER REPAIRDeal with any faults.
Carry out a road test, then check with the diagnostic tool.
EDC16_V44_DF097/EDC16_V48_DF097/EDC16_V4C_DF097

13B-93
DIESEL INJECTION
Fault finding - Interpretation of faults
13B
V10 MR-372-J84-13B150$376.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF119
STORED
CAMSHAFT SENSOR SIGNAL
1.DEF : intermittent absence of signal
2.DEF : intermittent inconsistency of signal
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared stored following a road test or after attempting to start the engine
several times.
Special notes:
Use bornier Ele. 1681 for all operations on the injection computer connectors.
Check the camshaft sensor connections.
Check the injection computer connections.
Check that the camshaft sensor is correctly positioned and mounted.
Also check the general condition, (damaged housing, heating up, etc.)
Carry out the necessary repairs.
Check the camshaft sensor resistance between tracks 2 and 3.
If the resistance is not 10250Ω ± 500 at 20°C, replace the sensor.
Check the continuity and absence of interference resistance of the following connections:
Injection computer brown 48-track connector B, track D1 Track 2 Camshaft sensor.
Injection computer brown 48-track connector B, track A1 Track 1 Camshaft sensor.
With the ignition on and the camshaft sensor connected:
Use a voltmeter to measure the voltage between tracks 1 and 3 of the camshaft sensor:
(This voltage should be equal to the battery voltage ± 0.08 V)
– If the voltage is outside permitted tolerance values, take the measurement again with the camshaft sensor
disconnected,
– If the voltage is still outside the permitted tolerance values with the sensor disconnected, check the continuity
and absence of interference resistance on the following connection:
Camshaft sensor, track 3 Track 2, PPM1 UPC connector
– If the voltage displayed is correct with the sensor disconnected, replace the camshaft sensor.
If the fault is still present, check the timing adjustment.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test, then check with the diagnostic tool.
EDC16_V44_DF119/EDC16_V48_DF119/EDC16_V4C_DF119

13B-108
DIESEL INJECTION
Fault finding - Interpretation of faults
13B
V10 MR-372-J84-13B150$376.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF1070
PRESENT
OR
STOREDCOLD LOOP
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present with the engine running and a heating and air
conditioning request
Priorities when dealing with a number of faults:
Firstly, deal with the following faults:
– DF049 Refrigerant sensor circuit if it is present or stored.
When the fault is present or stored, the heating and air conditioning system is inhibited.
Check fuse F22 (10A) of the UPC and the condition of the air conditioning compressor connector.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the air conditioning compressor wiring.
If the wiring is faulty and there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Manually check if the compressor is jammed (turn the clutch plate manually to check that there is no point of
resistance). In the event of sticking, replace the air conditioning compressor (see MR 364 (Mégane II) or 370
(Scénic II), Mechanical, Heating and air conditioning system, 62A, Air conditioning, Compressor: Removal
- Refitting).
Top up with freon, check for any leaks and repair if necessary (see MR 364 (Mégane II) or 370 (Scénic II),
Mechanical, Heating and air conditioning system, 62A, Air conditioning, Refrigerant circuit: check,
Refrigerant circuit: Draining - Filling).
AFTER REPAIRDeal with any faults.
Carry out a road test, then check with the diagnostic tool.
EDC16_V44_DF1070/EDC16_V48_DF1070/EDC16_V4C_DF1070

13B-110
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$423.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
MAIN COMPUTER STATUSES AND PARAMETERS (continued)
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool. The values shown in this conformity check are given as examples.
Test conditions: engine stopped, ignition on.
Order FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
5 PressurePR035:Atmospheric
pressureIndicates the
atmospheric pressure
in mbar.
The sensor is built into
the computer.
Default value:
750 mbarIn the event of a fault,
consult the interpretation
of fault DF003 Atmospheric
pressure sensor circuit.
PR038:Rail pressure0 consult the interpretation
of fault DF007 Rail pressure
sensor circuit.
6 TemperaturePR059: Inlet air
temperatureIndicates the inlet air
temperature
Ignition on
PR061 = PR059
Default value: 20°C In the event of a fault, refer
to the interpretation
of parameter PR059.
PR064: Coolant
temperatureShows the engine
coolant temperature
in °C
Default value: 119°C.In the event of a fault,
refer to the interpretation
ofDF001 Coolant
temperature sensor
circuit.
7 Preheating ET007: Pre-postheating
controlINACTIVE
or
ACTIVEIn the event of a fault,
refer to the interpretation
of statusET007.
8 Torque PR015: Engine torqueX = 0 NmNone.
9Charging
circuit PR016:Alternator flow X = 0 mAIn the event of a fault,
check the charge circuit.

13B-120
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$423.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
HEATING
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool. The values shown in this conformity check are given as examples.
Test conditions: engine stopped, ignition on.
Order FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
1Coolant
temperaturePR064: Coolant
temperatureShows the engine
coolant temperature
in °C
Default value: 119°C.In the event of a fault,
refer to the interpretation
ofDF001 Coolant
temperature sensor
circuit.
2Resistance
Heating
Passenger
compartmentET111: Set number
of RCHIndicates the number
of passenger
compartment resistors
supplied.
The passenger
compartment resistor
function programming
is performed through
the UCH.
Certain operating
parameters determine
the operation of one
or more passenger
compartment resistors.
The injection computer
only receives a signal
relating to the number
of passenger
compartment resistors
to control.
Ignition on
ET111 = NOIn the event of a fault,
(see 87B, UCH).
ET112: RCH cut-offStatus ET112 is
indicated if the
passenger
compartment resistors
are being controlled.
The computer receives
the signal to cut-off
the resistors through
the UCH.
Ignition on
ET112 = YES

13B-125
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$423.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
IGNITION/PREHEATING
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool. The values shown in this conformity check are given as examples.
Test conditions: engine stopped, ignition on.
Order FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
1 Power supply ET001: + After ignition
computer feedIgnition on PRESENTIf the event of a fault, carry
out fault finding on
thecharge circuit.
2 Engine speed PR055: Engine speed Indicates the engine's
rotation speed in rpm.In the event of a fault,
consult the interpretation
of fault DF005 Engine
speed sensor circuit.
3 TemperaturePR064: Coolant
temperatureShows the engine
coolant temperature in
°C
Default value: 119°C.In the event of a fault,
refer to the interpretation
ofDF001 Coolant
temperature sensor
circuit.
PR059:Inlet air
temperatureIndicates the inlet air
temperature
Default value: 20°C.In the event of a fault,
refer to the interpretation
of fault DF039 Inlet air
temperature sensor
circuit.
4 Preheating ET007: Preheating unit
controlStatus ET007 is
ACTIVE a few seconds
after the ignition is
switched on, and for
postheatingIn the event of a fault,
(ET007 locked in ACTIVE
status), consult
the interpretation of fault
DF017 Preheating unit
control circuit.

13B-129
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$423.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
MAIN COMPUTER STATUSES AND PARAMETERS (continued)
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool. The values shown in this conformity check are given as examples.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
5PressurePR035: Atmospheric
pressureIndicates the
atmospheric pressure
in mbar. The sensor is
built into the computer.
Default value:
750 mbar.In the event of a fault,
consult the interpretation
of fault DF003
Atmospheric pressure
sensor circuit.
PR038: Rail pressure250< P< 300bar
Pmax = 1350 barIn the event of a fault,
consult the interpretation
of fault DF007 Rail
pressure sensor circuit.
6 TemperaturePR059: Inlet air
temperatureIndicates the inlet air
temperature
Default value: 20°CIn the event of a fault, refer
to the interpretation
of parameter PR059.
PR064: Coolant
temperatureShows the engine
coolant temperature in
°C
Default value: 119°C.In the event of a fault, refer
to the interpretation
ofDF001 Coolant
temperature sensor
circuit.
7 Preheating ET007: Pre-postheating
controlINACTIVE
warm engineIn the event of a fault, refer
to the interpretation of status
ET007.
8 Torque PR015: Engine torqueWhen starting:
25 < X < 40 N.m
At idle speed:
2 9Charging
circuitPR016: Alternator flowWarm engine
10 < X < 20 mA
With consumers:
25 check the charge circuit.