check RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Injection Repair Manual

13B-74
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF056
PRESENT
OR
STORED
AIR FLOWMETER CIRCUIT
CC.1 : short circuit to + 12 V
CO.0 : open circuit or short circuit to earth
1.DEF : offset at maximum threshold
2.DEF : offset at minimum threshold
3.DEF : parameter at max limit
4.DEF : parameter at minimum limit
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine is started or following a road test.
Special notes:
Use bornier Elé. 1681 for all operations on the injection computer connectors.
CC.1
NOTESNone.
Check the air flowmeter connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity and insulation against + 12 V of the following connections:
Injection computer brown 48-track connector B, track E2 Track 2 air flow sensor
Injection computer brown 48-track connector B, track L4 Track 6 air flow sensor
Injection computer brown 48-track connector B, track G1 Track 5 air flow sensor
Injection computer brown 48-track connector B, track B4 Track 3 air flow sensor
Injection computer brown 48-track connector B, track G2 Track 1 air flow sensor
If the fault is still present, replace the air flowmeter.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF056/EDC16_V48_DF056/EDC16_V4C_DF056

13B-75
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF056
CONTINUED 1
CO.0
NOTESNone.
Check that there is a + 5 V supply on track 3 of the air flowmeter.
Repair if necessary.
Check the air flowmeter connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity and insulation against earth between:
Injection computer brown 48-track connector B, track E2 Track 2 air flow sensor
Injection computer brown 48-track connector B, track B4 Track 3 air flow sensor
Injection computer brown 48-track connector B, track G1 Track 5 air flow sensor
Injection computer brown 48-track connector B, track G2 Track 1 air flow sensor connector
Injection computer brown 48-track connector B, track L4 Track 6 air flow sensor connector
PPM1 black connector of the UPC track 2 Track 4 air flow sensor connector
Repair if necessary.
If the fault is still present and remains present, replace the air flowmeter.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.

13B-76
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF056
CONTINUED 2
1.DEF
2.DEF
NOTESNone.
3.DEF
4.DEF
NOTESConditions for applying the fault finding procedure to
a stored fault:
The fault is declared present after the ignition has been
switched off for 15 seconds.
Check the air flowmeter connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity and absence of interference resistance of the following connections:
Injection computer, brown 48-track connector B, track B4 Track 3 air flow sensor
Injection computer brown 48-track connector B, track G1 Track 5 air flow sensor
Injection computer, brown 48-track connector B, track L4 Track 6 air flow sensor
Injection computer, brown 48-track connector B, track E2 Track 2 air flow sensor
Injection computer, brown 48-track connector B, track G2 Track 1 air flow connector
PPM1 black connector of the UPC track 2 Track 4 air flow sensor connector
Repair if necessary.
Check the entire air inlet circuit:
– air filter unit inlet not blocked and filter not clogged,
–no foreign bodies on the air flow sensor grille (visual inspection only).
Otherwise, replace the air flow sensor.
– oil vapour recirculation circuit connected correctly,
–no leaks or blockages in the low and high pressure air circuits: pipes, presence and tightness of the mounting
clips, mounting of the turbocharger pressure sensor, intercooler, etc.
– check that the damper valve is open (valve control is against the body of the air vent unit).
With the flowmeter connected, the vehicle ignition on and engine stopped:
– check the voltage between tracks 2 and 5 of the flowmeter:
If the value is not 0.6 V ± 0.1, replace the air flow sensor.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.

13B-77
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF056
CONTINUED 3
●Check the EGR valve is not jammed open:
– remove the EGR valve:
– with the valve removed and connected, run command AC002 EGR valve.
Check: the movement of the valve,
that it closes when the command is completed.
If these checks show that the valve is jammed or irrevocably seized, replace the EGR valve.
If no faults are revealed, but the fault is still present, replace the air flowmeter.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.

13B-78
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF057
PRESENT
OR
STOREDWATER IN DIESEL FUEL DETECTOR CIRCUIT
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after the engine is started or following a road test.
A) Make sure the water in diesel fuel detection sensor is properly connected.
– If not, clear the fault,
– carry out a road test (speed > 12 mph (20 km/h) at an engine speed of> 1200 rpm) for more than 30 seconds.
– If the fault does not recur, end the fault finding procedure.
– If the fault does recur, go to step B.
B) If the sensor is properly connected:
– drain the diesel filter unit (seeMR 364, 13A, Fuel supply),
– clear the fault,
– carry out a road test (speed > 12 mph (20 km/h) at an engine speed of> 1200 rpm) for more than 30 seconds.
If the fault does not recur, end the fault finding procedure.
C) If the fault recurs:
–Check the continuity and the absence of unwanted resistance on the connection between:
Injection computer, grey 32-track connector C, track A2 Track 3 of the water detection sensor
–Check the power supply to the water detection sensor:
UPC PPM1 black connector track 2 Track 1 the water detection sensor
Earth Track 2 water detection sensor
– Carry out the necessary repairs.
If none of these checks reveal any faults:
– Replace the water detection sensor (see MR 364, 13A, Fuel supply).
– Clear the fault.
– Carry out a road test (speed > 12 mph (20 km/h) and engine speed > 1200 rpm) for more than 30 seconds,
to confirm the repair.
Note:
if the level of water in the fuel filter unit is lower than the sensor electrodes, certain driving conditions (on a bend,
leaning) may causethe injection warning light to light up erratically.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF057/EDC16_V48_DF057/EDC16_V4C_DF057

13B-79
DIESEL INJECTION
Fault finding - Interpretation of faults
13B
V10 MR-372-J84-13B150$376.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4CDIESEL INJECTION
Fault finding - Interpretation of faults
DF067
PRESENT
OR
STOREDDAMPER CONTROL CIRCUIT
CC.1 : short circuit to + 12 V
CC.0 : short circuit to earth
CO : open circuit
1.DEF : internal electrical fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after:
– the engine is started,
– a road test,
– an actuator command C014 Damper valve.
Special notes:
If the fault is present:
– it is difficult or even impossible to start the vehicle.
– the level 2 warning light is lit.
Use bornier Ele. 1681 for all operations on the injection computer connectors.
CC.1
NOTESNone.
Check the connections of the damper valve solenoid valve.
Check the injection computer connections.
Repair if necessary.
Measure the resistance between tracks 1 and 2 of the damper flap solenoid valve:
The resistance should be between 43 and 49Ω at 25°C.
Replace the solenoid valve if the resistance is outside the tolerance values.
Check the continuity and insulation from + 12 V of the following connection:
Injection computer, brown 48-track connector B, track J4 Track 1 damper valve solenoid valve
Repair if necessary.
If the fault is still present, replace the damper valve solenoid valve.
AFTER REPAIRDeal with any faults.
Carry out a road test, then check with the diagnostic tool.
EDC16_V44_DF067/EDC16_V48_DF067/EDC16_V4C_DF067
MR-372-J84-13B150$376.mif

13B-80
DIESEL INJECTION
Fault finding - Interpretation of faults
13B
V10 MR-372-J84-13B150$376.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF067
CONTINUED 1
CO.0
CO
NOTESNone.
Check the connections of the damper valve solenoid valve.
Repair if necessary.
Measure the resistance between tracks 1 and 2 of the damper flap solenoid valve:
– The resistance should be between 43 and 49Ω at 25°C,
– Replace the solenoid valve if the resistance is outside the tolerance values.
Check the continuity and insulation from earth of the following connections:
Injection computer, brown 48-track connector B, track J4 Track 1 damper valve solenoid valve
UPC PPM1 black connector track 2 Track 2 damper valve
solenoid valve
Repair if necessary.
If the fault is still present, replace the damper valve solenoid valve.
AFTER REPAIRDeal with any faults.
Carry out a road test, then check with the diagnostic tool.

13B-81
DIESEL INJECTION
Fault finding - Interpretation of faults
13B
V10 MR-372-J84-13B150$376.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF067
CONTINUED 2
1.DEF
NOTESNone.
Check the connections of the damper valve solenoid valve.
Check the injection computer connections.
Repair if necessary.
Measure the resistance between tracks 1 and 2 of the damper flap solenoid valve:
– The resistance should be between 43 and 49Ω at 25°C,
– Replace the solenoid valve if the resistance is outside the tolerance values.
Check the continuity, insulation, and the absence of interference resistance of the following connection:
Injection computer, brown 48-track connector B, track J4 Track 1 damper valve solenoid valve
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test, then check with the diagnostic tool.

13B-82
DIESEL INJECTION
Fault finding - Interpretation of faults
13B
V10 MR-372-J84-13B150$376.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF069
PRESENT
IMPACT DETECTED SIGNAL
NOTESFault finding procedure application conditions:
Only apply the procedure if the fault is present and if the vehicle does not start.
Special notes:
The fault appears when the injection computer receives a frontal impact signal from the
Airbag computer via the multiplex network.
As soon as the injection computer receives this signal, engine operation is inhibited
and the level 2 warning light is lit.
Use bornier Ele. 1681 for all operations on the injection computer connectors.
If the vehicle has been involved in an accident:
Carry out any necessary repairs:
– clear the fault,
– switch off the ignition and wait 30 seconds,
– wait for the engine immobiliser indicator light to flash,
– switch on the ignition,
If the fault does not reappear, end of fault finding procedure.
If the fault recurs, carry out fault finding on the AIRBAG computer.
If the vehicle has not been involved in an accident, carry out fault finding on the Airbag computer.
AFTER REPAIRDeal with any faults.
Carry out a road test, then check with the diagnostic tool.
EDC16_V44_DF069/EDC16_V48_DF069/EDC16_V4C_DF069

13B-83
DIESEL INJECTION
Fault finding - Interpretation of faults
13B
V10 MR-372-J84-13B150$376.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF070
PRESENT
OR
STOREDCLUTCH SWITCH CIRCUIT
1.DEF : no signal
2.DEF : inconsistent signal
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after the clutch pedal is depressed, or during a road test.
Special notes:
Use bornier Ele. 1681 for all operations on the injection computer connectors.
WARNING
This fault may appear if the wiring harness has been damaged.
Follow the procedure described in the Wiring Check in the Introduction.
This check enables the condition and the conformity of the engine wiring harness to be checked.
Check the conformity and adjustment of the clutch switch (position, connection).
– display status ET405 Clutch pedal switch,
– when the clutch pedal is engaged, status ET405 should be INACTIVE,
– when the clutch pedal is disengaged, status ET405 should be ACTIVE,
If these checks are not OK, replace the clutch switch.
If these checks are correct:
Check the connections of the clutch pedal switch.
Check the injection computer connections.
Repair if necessary.
Check for continuity and the absence of interference resistance on the following connection:
Injection computer black 32-track connector A, track C4 Track 1 Clutch pedal switch
Repair if necessary.
Check for earth on track 2 of the clutch pedal switch.
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test, then check with the diagnostic tool.
EDC16_V44_DF070/EDC16_V48_DF070/EDC16_V4C_DF070