lock RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Owner's Guide

13B-339
MR-372-J84-13B200$900.mif
V13
13B
DIESEL INJECTION
Fault finding – Tests
TEST 1 Exhaust system check
Engine stopped:
Check that the silencer outlet is not blocked.
Repair or replace the silencer, if necessary.
Check the seal of the exhaust manifold on the contact
surface between the turbocharger and the exhaust
manifold.
Is the seal in order?
YES
Loosen the catalytic converter on the turbocharger side.
Place a wooden block between the two parts.
Start the vehicle and check if the engine runs better.
Is the engine running normally?
YES
A
NORepair or replace the faulty part.
NOThe exhaust pipe is not the cause
of the fault, continue with the
engine fault finding procedure (see
Customer complaints).
EDC16_V50_TEST1/EDC16_V58_TEST1/EDC16_V5C_TEST1/EDC16_V18_TEST1/EDC16_V1C_TEST1/EDC16_V20_TEST1 EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5C
MR-372-J84-13B200$900.mif

13B-340
MR-372-J84-13B200$900.mif
V13
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5CDIESEL INJECTION
Fault finding – Tests13B
TEST 1
CONTINUED
Retighten the catalytic converter.
Loosen or uncouple the particle filter on the catalytic
converter side. Place a wooden block between the two
parts if necessary.
Start the vehicle and check if the engine runs better.
Is the engine running normally?Replace the catalytic converter.
Retighten the particle filter.
Loosen or uncouple the silencer on the particle filter side
(see MR 364 (Mégane II), 370 (Scénic II) or 395 (Laguna
II), Mechanical, 19B Exhaust, Parts and consumables
for repair).
Start the vehicle and check if the engine runs better.
Is the engine running normally?Replace the particle filter (see MR
364 (Mégane II), 370 (Scénic II) or
395 (Laguna II), Mechanical, 19B
Exhaust, Particle filter, Removal –
Refitting).
After any operation on the particle
filter, reinitialise the parameters.
Run command SC036 Reinitialise
programming and select After
particle filter replacement.
Check the weight of soot: if PR383
Weight of soot in the particle filter
≥ 1 g. Apply the procedure for test 8
Manual clearing of the soot weight.
Replace the silencer.
A
YES
NO
YES
NO
YES

13B-344
MR-372-J84-13B200$900.mif
V13
DIESEL INJECTION
Fault finding – Tests
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5C
13B
TEST 3
CONTINUED
Check the condition of the priming bulb, and that it is working properly.
Perform repairs if necessary and continue the test.
If the fault is still present with a low fuel level, check the consistency of the actual fuel level and that indicated on
the instrument panel.
– The transfer pump is supplied via a venturi valve located beneath it.
Check that the opening of the venturi (6 to 8 mm in diameter) is not blocked by dirt contained in the fuel tank.
Check the priming of the low pressure diesel circuit.
Check the conformity of the fuel used by running test 11 Diesel fuel conformity check.
If the diesel fuel is not correct:
– Replace the diesel fuel.
– Change the diesel filter.
– Bleed the low and high pressure diesel circuit.
Low pressure circuit correct.
END OF TEST3.

13B-345
MR-372-J84-13B200$900.mif
V13
DIESEL INJECTION
Fault finding – Tests
EDC16
Program No.: C1
Vdiag no.: 18, 1C, 20,
50, 58, 5C
13B
TEST 4 Checking the turbocharged air inlet circuit
Engine stopped:
Check the sealing of the low and high pressure air circuits (air leak or intake) both upstream and downstream of
the turbocharger.
Check the parts that are abnormally greasy of the circuit and reveal a lack of tightness.
Check:
– the condition and fitting of the ducts (foreign, clogged, not joined, kinked, broken, pierced, cut bodies, tightness
of the mounting bolts, etc.).
– the presence, condition and fitting of the seals.
– the present and tightening of the clamps.
– The fitting of the turbocharging pressure sensor.
Carry out the necessary repairs.
Checking the air filter.
Check:
– That the air filter unit inlet and outlet are not blocked.
– the condition and the assembly of the air filter unit (disconnected, broken, pierced …).
– The cleanliness, conformity and the absence of deformation of the filter element.
– The air flowmeter: run Test 5 Air flowmeter.
Carry out the necessary repairs.
If the engine is equipped accordingly, check:
– that the damper valve is open (AC012 Damper valve, step B).
– the condition of the damper valve:
– the tightening of the mounting bolts,
– cracks in the damper valve.
Carry out the necessary repairs.
Replace the valve if necessary.
Check that there is no leak at the exhaust manifold, in particular at the exhaust manifold/turbocharger connection.
Check the exhaust, run Test 1 Exhaust system check.
Carry out the necessary repairs.
Check the condition of the intercooler:
– clogging,
– leaks (vehicle stationary, stabilise the engine speed between 3500 rpm and 4000 rpm and check that there are
no leaks).
Replace the intercooler if necessary.
End of test.
EDC16_V50_TEST4/EDC16_V58_TEST4/EDC16_V5C_TEST4/EDC16_V18_TEST4/EDC16_V1C_TEST4/EDC16_V20_TEST4