abs RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Manual PDF

13B-217
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR007
RAIL PRESSURE REGULATOR CURRENT SETPOINT
PARAMETER
DEFINITIONThis parameter indicates the current setpoint absorbed by the rail pressure regulator.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on.
395 mA < PR007 < 405 mA
Default value: 1600 mA
In the event of a fault, refer to the interpretation of faults DF053 Rail pressure regulation function and DF007
Rail pressure sensor circuit.
Engine running, engine coolant temperature > 80°C.
1350 mA < PR007 < 1450 mA
Default value: 1600 mA
In the event of a fault, consult the interpretation of fault DF007 Rail pressure sensor circuit.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR007/EDC16_V58_PR007/EDC16_V5C_PR007/EDC16_V18_PR007/EDC16_V1C_PR007/EDC16_V20_PR007

13B-225
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR030
ACCELERATOR PEDAL POSITION
PARAMETER
DEFINITIONThis parameter indicates the accelerator pedal position as a percentage.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
No faults should be present or stored.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (e.g. lack of power).
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C.
If no pressure is being applied to the pedal PR030 = 0%.
In the event of a fault, refer to the interpretation of fault DF008 Pedal potentiometer circuit gang 1 or DF009
Pedal potentiometer circuit gang 2.
Sensor electrical conformity.
Check the continuity and absence of interference resistance of the following connections:
– connection code 3LR,
– connection code 3LS,
– connection code 3LT,
– connection code 3LU,
– connection code3LW,
– connection code 3LV.
Between components 120 and 921.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repairs), repair the wiring; otherwise replace the wiring.
Pedal sensor connected, vehicle ignition on and engine stopped:
– check the value of PR030:
0% no load,
100% full load,
138% full load after kickdown point on pedal.
– if the value is not correct, replace the pedal sensor.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR030/EDC16_V58_PR030/EDC16_V5C_PR030/EDC16_V18_PR030/EDC16_V1C_PR030/EDC16_V20_PR030

13B-229
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR038
CONTINUED
Sensor electrical conformity.
Check the condition of the rail pressure sensor connector (see Wiring Diagram Technical Note, Vehicle,
component code 1032).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Vehicle, component code 120).
If one of the connectors is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, wiring: precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and absence of interference resistance of the following connections:
– connection code 3LX,
– connection code 3LY,
– connection code 3LZ.
Between components 120 and 1032.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Electrical wiring
repair, Wiring: precautions for repairs), repair the wiring; otherwise replace the wiring.
Check that there are no external diesel leaks from the high pressure fuel circuit.
With the ignition on and the engine stopped for over 1 minute:
Display parameter PR038.
– If the pressure is below 90 bar, the sensor is in order.
– If the pressure is above 90 bar, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-230
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR041
TURBOCHARGING PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the turbocharging pressure in mbar.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C.
The turbocharging pressure value is:
PR041 = PR035 “Atmospheric pressure” ± 10 mbar
In the event of a fault, apply the interpretation of DF004 Turbocharging pressure sensor circuit.
Sensor electrical conformity.
Check the continuity and absence of interference resistance on the following connections:
For Mégane II and Scénic II:
– connection code 3LQ,
– connection code 3LP,
– connection code 3LN.
Between components 120 and 1071.
For Laguna II:
– connection code 3LQ,
– connection code 3LP,
– connection code 3LN.
Between components 120 and 1474.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Electrical wiring
repair, Wiring: precautions for repairs), repair the wiring; otherwise replace the wiring.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_PR041/EDC16_V58_PR041/EDC16_V5C_PR041/EDC16_V18_PR041/EDC16_V1C_PR041/EDC16_V20_PR041

13B-231
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR041
CONTINUED
Vehicle with ignition on, and the engine stopped for over 1 minute:
Compare the values of PR041 and PR035 Atmospheric pressure.
If the difference between PR041 and PR035 Atmospheric pressure is greater than 0.1 bar,
check the value of PR035 Atmospheric pressure by comparing it with the reading on a vehicle in the workshop
which is correct.
If the value of PR035 Atmospheric pressure is not correct (difference greater than 0.1 bar between
the 2 vehicles), contact the Techline.
Otherwise (when the value PR035 Atmospheric pressure is correct), change the turbocharging pressure
sensor.
If the difference between PR041 and PR035 Atmospheric pressure is less than 0.1 bar.
Start the engine, with the engine idling:
Compare the values of PR041 and PR035 Atmospheric pressure.
If the difference between PR041 and PR035 Atmospheric pressure is greater than 0.2 bar.
Check the air inlet circuit:
absence of leaks or blockages in the low and high pressure air circuit: ducts, presence and tightness of the
mounting clips, mounting of the turbocharger pressure sensor, intercooler, etc.
Check that the damper valve is not jammed closed.
Repair if necessary.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-241
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR064
CONTINUED
Sensor electrical conformity.
Check the continuity and absence of interference resistance on the following connections:
– connection code3C,
– connection code 3JK.
Between components 120 and 244.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance between connections 3C and 3JK of component 244.
Replace the sensor if the resistance is not:
11332 Ω < PR064 < 13588 Ω at - 10°C
2140 Ω < PR064 < 2364 Ω at + 25°C
772 Ω < PR064 < 850 Ω at + 50°C
275 Ω < PR064 < 291 Ω at + 80°C
112 Ω < PR064 < 118 Ω at + 110°C
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

13B-250
MR-372-J84-13B200$648.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR089
VEHICLE SPEED
PARAMETER
DEFINITIONGives the vehicle speed in mph (km/h).
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
This parameter is transmitted by the ABS computer.
This signal is transmitted to the injection on the multiplex network.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C.
In the event of a fault, test the multiplex network (see 88B, Multiplexing).
Then complete fault finding on the ABS computer (see38C, Anti-lock braking system).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR089/EDC16_V58_PR089/EDC16_V5C_PR089/EDC16_V18_PR089/EDC16_V1C_PR089/EDC16_V20_PR089

13B-256
MR-372-J84-13B200$648.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR132
CONTINUED
Sensor electrical conformity.
Test the air inlet circuit (from the air filter inlet to the inlet manifold tracts,
apply test 4 Turbocharged air inlet circuit check):
– air filter unit inlet not blocked and filter not clogged,
–visual inspection only, run test 4 Turbocharged air inlet circuit check for ALP2 Starting difficult or
impossible,
– oil vapour recirculation circuit connected correctly,
–absence of leaks or blockages in the low and high pressure air circuits: ducts, presence and tightness of the
mounting clips, mounting of the turbocharging pressure sensor, intercooler, etc.
– check that the damper valve is not jammed.
Carry out the necessary repairs.
Check the electrical conformity of the air flowmeter:
Check the + 5 V supply to the air flowmeter on connection 3KJ between components 120 and 799.
Check the + 12 V after relay supply to the air flowmeter on connection 3B between components 120 and 799.
Check the continuity and the absence of interference resistance on the following connections:
– connection code 3DV,
– connection code 3DW.
Between components 120 and 799.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Electrical wiring
repair, Wiring: precautions for repairs), repair the wiring; otherwise replace the wiring.
With the flow meter connected, the vehicle ignition on and engine stopped:
Measure the voltage between connections 3DV and 3DW between components 120 and 799.
Replace the air flowmeter if its voltage is not approximately 0.5 V < PR073 Air flowmeter supply voltage < 0.7 V.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-302
MR-372-J84-13B200$756.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of commands
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
AC001
PRE-POSTHEATING UNIT
NOTESThis command is only run if fault DF025 Preheating unit diagnostic line or DF017
Preheating unit control circuit is present or stored and if no other faults are present.
Refer to the Wiring Diagrams Technical Note for the vehicle to locate the fuses and
relays concerned.
Switch on the ignition and connect the diagnostic tool.
with the pre-postheating unit connected:
– connect the negative terminal of the voltmeter to connection 3FF of component 257,
– connect the positive terminal of the voltmeter to the + 12 V battery,
– run command AC001.
If the voltmeter does not indicate the battery voltage while the command is running (ten 1-second ON/OFF
cycles):
1- Check the condition of the preheating unit supply fuse F01 (70A).
Replace it if necessary.
2- Check the continuity and the absence of interference resistance of the following connections:
– connection code 3FF,
– connection code 3FY.
Between components 120 and 257.
If the connection or connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Repair if necessary.
3- Check the connections on the preheating unit, heater plugs and injection computer.
Repair if necessary.
4- Measure the resistance of the heater plugs. If this resistance is greater than 2 Ω, replace the faulty plug(s).
5- Check the continuity and the absence of interference resistance between the following connections:
– connection code 37AB,
– connection code 37Z,
– connection code 37AC,
– connection code 37AA.
Between components 257, 680, 681, 682 and 683.
If the connection or connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
6- Check for + 12 V on connectionBP35 of component257.
if the fault is still present, replace the preheating unit
EDC16_V50_AC001/EDC16_V58_AC001/EDC16_V5C_AC001/EDC16_V18_AC001/EDC16_V1C_AC001/EDC16_V20_AC001

13B-303
MR-372-J84-13B200$756.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of commands
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
AC004
TURBOCHARGING SOLENOID VALVE
NOTESthis command is used to check the turbocharging circuit.
This command checks that the turbocharger and the control circuit are working properly.
Introduction
1- check the sealing of the high-pressure air circuit:
Pipes not joined or pierced, pressure sensor disconnected or poorly fitted (seal present), intercooler pierced. To
check the intercooler: with the vehicle stopped, stabilise the engine speed between 3500 rpm < X < 4000 rpm
and check that there are no leaks.
Check the resistance of the turbocharging pressure relief solenoid valve between connections 3FB and 3MG.
Replace the solenoid valve if its resistance is not: 14.7 Ω < X < 16.1 Ω at 20°C.
Check the injection computer connections.
Check the continuity and absence of interference resistance of connection 3MG between components 120
and 1475.
If the connection or connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V after relay on connection 3FB of component 1475.
2- turbocharger control circuit check
– with the engine stopped, check that the control rod is (in the rest position the control rod is retracted),
– start the engine and check that the control rod disengages and pulls on the turbocharger geometry (when the
engine is stopped, the control rod should return to the rest position).
– if the control rod does not move correctly, carry out the following checks:
1) Vacuum pressure command check:
– Disconnect the solenoid valve inlet hose and connect it to a pressure gauge.
– Start the engine and run it at a stable idle speed.
– if the vacuum is not between 700 mbar < X < 900 mbar, check the vacuum circuit from the vacuum pump.
– Stop the engine, reconnect the inlet hose and go to step no. 2.
2) Solenoid valve control check:
– Disconnect the solenoid valve outlet hose.
– Start the engine and run it at a stable idle speed.
– Place your hand on the solenoid valve and block the outlet union with your thumb.
– If there is no perceptible vibration of the solenoid valve, check that the computer output is working correctly
(step 5) and check solenoid valve operation:
– Connect the pressure gauge to the solenoid valve outlet union.
– Start the engine and run it at a stable idle speed.
if the vacuum is not between 700 mbar < X < 900 mbar, replace the solenoid valve.
EDC16_V50_AC004/EDC16_V58_AC004/EDC16_V5C_AC004/EDC16_V18_AC004/EDC16_V1C_AC004/EDC16_V20_AC004