warning lights RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 User Guide

13B-115V9 MR-372-J84-13B450$102.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF107
PRESENT
OR
STOREDCOMPUTER MEMORY
1.DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the ignition has been switched on
Special notes:
The level 1 and European On Board Diagnostic warning lights are lit.
Use bornier Elé.1681 for any operations on the injection computer connectors.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
If the fault is stored, clear the fault from the computer memory.
– Switch off the ignition and wait for the diagnostic tool message (maximum time 8minutes) Communication
lost with computer: EDC16 C36, check the tool connection and computer power supply before switching
the ignition back on.
Start the engine and re-establish dialogue.
This fault may be linked to a write error following disconnection of the battery when the computer was in the
process of writing to the EEPROM phase (computer memory).
If this is the case, loading a new calibration will remove the fault.
If a more recent calibration is available, load this calibration on to the computer.
If the fault is still present:
– use the command RZ034 Computer memory,
– Switch off the ignition and wait for the computer dialogue lost message,
– switch on the ignition again,
– define the injector codes using the control SC002 Enter injector codes.
– Run the programming commands (See configuration and programming),
– switch off the ignition and wait for the message loss of communication with the computer.
Perform a road test to reinitialise the vehicle parameters.
EDC16C36_V44_DF107/EDC16C36_V4C_DF107/EDC16C36_V48_DF107/EDC16C36_V50_DF107/EDC16C36_V54_DF107/
EDC16C36_V58_DF107
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-178
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$104.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
* diff: differential
DF316
PRESENT
OR
STOREDPARTICLE FILTER DIFF* PRESSURE
1.DEF: Signal incoherent
2.DEF: Below minimum threshold
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– the ignition is switched on.
– the engine is started.
Special notes:
If the fault is present:
– the particle filter fault finding procedure is inhibited,
–the Level 1 and OBD warning lights are lit.
Use bornier Ele. 1681 for all operations on the engine management computer
connector.
Use Wiring Diagram Technical Note, Mégane II ph2, Scénic II ph2.
Check the condition of the pressure pipes on the differential pressure sensor.
Check that they are sealed and in the correct position.
Replace if necessary.
Check the condition of the connectors on the differential pressure sensor and the injection computer.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Check the continuity, insulation and the absence of interference resistance on the following connections:
– Connection code3AAQ,
– Connection code3TM,
– Connection code 3TL,
between components 1290 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
EDC16C36_V48_DF316/EDC16C36_V50_DF316/EDC16C36_V58_DF316EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-217V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET042CRUISE CONTROL/SPEED LIMITER
STATUS DEFINITIONNOT DETECTED: This status indicates that the cruise control or speed limiter function
is not present on the vehicle.
INACTIVE: This status indicates that the main On/Off switch of the cruise control/speed
limiter is in the rest (or neutral) position.
LIMITER: This status indicates that the driver has used the main switch to select the
speed limiter.
CRUISE CONTROL: This status indicates that the driver has used the main switch to
select the cruise control.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Use the Mégane II ph2, Scénic II ph2 Technical Note wiring diagram.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C
NOT DETECTEDThe cruise control or speed limiter function is not present on the vehicle.
INACTIVENo button has been pressed.
SPEED LIMITERThe speed limiter ON/OFF button has been pressed.
Lights the orange warning light on the instrument panel.
CRUISE
CONTROL
The cruise control ON/OFF button has been pressed.
Lights the green warning light on the instrument panel.
EDC16C36_V44_ET042/EDC16C36_V4C_ET042/EDC16C36_V48_ET042/EDC16C36_V50_ET042/EDC16C36_V54_ET042/
EDC16C36_V58_ET042
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-386
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
V9 MR-372-J84-13B450$190.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP4 Poor performance
NOTESBefore analysing this customer complaint, check that there are no faults, and the
conformity (or otherwise) of the parameters and statuses, using the diagnostic
tool.
If the customer complaint is not eliminated, perform the following checks.
IMPORTANT
In the case of engine overheating to above 118°C, the computer deliberately limits the fuel flow (overheating
warning light lights up from 115°C).
Please observe the cleanliness guidelines and safety advice.
Is the poor performance accompanied by smoke?
Check the conformity of the fuel used by running test 11 Diesel fuel conformity check.
If the diesel fuel is not correct:
– Replace the diesel fuel.
– Change the diesel filter.
– Bleed the low and high pressure diesel circuit.
Test the high pressure fuel circuit:
Run the scenario SC035 High pressure fuel circuit fault finding (see Interpretation of commands).
Check that the injectors are correctly fitted (presence and conformity of the sealing washer).
Checking procedure:
– Take a straightedge approximately 40 cm long and place it on the 4 injectors. The straightedge should rest on
the 4 injectors.
– If 1 injector protrudes, remove the injector and check that the washer is correct.
– If one injector does not touch the straightedge (clearance of more than 1 mm), remove the injector and check
that the washer is present.
– Clean the injector wells and the injector, refit the injector with the correct sealing washer.
– The tightness seal and the condition of the inlet circuit: run test 4: Turbocharged air inlet circuit check.
– The condition of the air flowmeter, run test 5 Air flowmeter.
– The turbocharger, run the following tests:
– test 2: Air path at the turbocharger,
– test 6: Turbocharger control solenoid valve check,
– test 7: Turbocharger.
NOA
YES
EDC16C36_V44_ALP04/EDC16C36_V4C_ALP04/EDC16C36_V48_ALP04/EDC16C36_V50_ALP04/EDC16C36_V54_ALP04/
EDC16C36_V58_ALP04EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58