check engine RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 Workshop Manual

13B-297
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR080RAIL PRESSURE SENSOR VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the voltage of the rail pressure sensor in volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
0 V In the event of a fault, refer to the interpretation of fault DF013 Sensor feed voltage no. 3.
EDC16C36_V44_PR080/EDC16C36_V4C_PR080/EDC16C36_V48_PR080/EDC16C36_V50_PR080/EDC16C36_V54_PR080/
EDC16C36_V58_PR080EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-298
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR082FUEL TEMPERATURE SENSOR VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the voltage of the fuel temperature sensor in volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
0 V < PR082 < 5 V
In the event of a fault, consult the interpretation of DF098 Fuel temperature sensor circuit.
EDC16C36_V44_PR082/EDC16C36_V4C_PR082/EDC16C36_V48_PR082/EDC16C36_V50_PR082/EDC16C36_V54_PR082/
EDC16C36_V58_PR082EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-299
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR083AIR TEMPERATURE SENSOR VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the voltage of the air temperature sensor in volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
0 V < PR083 < 5 V
In the event of a fault, consult the interpretation of faults DF011 Sensor supply voltage no. 1, DF012 Sensor
supply voltage no. 2 and DF013 Sensor supply voltage no. 3.
EDC16C36_V44_PR083/EDC16C36_V4C_PR083/EDC16C36_V48_PR083/EDC16C36_V50_PR083/EDC16C36_V54_PR083/
EDC16C36_V58_PR083EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-300
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR084COOLANT TEMPERATURE SENSOR VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the voltage of the coolant temperature sensor in volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
0 V < PR084 < 5 V
In the event of a fault, refer to the interpretation of DF001 Coolant temperature sensor circuit.
EDC16C36_V44_PR084/EDC16C36_V4C_PR084/EDC16C36_V48_PR084/EDC16C36_V50_PR084/EDC16C36_V54_PR084/
EDC16C36_V58_PR084EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-301
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR086PEDAL POTENTIOMETER GANG 1 VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the voltage of the pedal potentiometer gang 1 in volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
Accelerator pedal released: 0.70 V < PR086 < 0.80 V
IMPORTANT
This corresponds to normal operation.
EDC16C36_V44_PR086/EDC16C36_V4C_PR086/EDC16C36_V48_PR086/EDC16C36_V50_PR086/EDC16C36_V54_PR086/
EDC16C36_V58_PR086EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-302
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR088PEDAL POTENTIOMETER GANG 2 VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the voltage of the pedal potentiometer gang 2 in volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
Accelerator pedal released: 0.30 V < PR088 < 0.40 V
IMPORTANT
This corresponds to normal operation.
EDC16C36_V44_PR088/EDC16C36_V4C_PR088/EDC16C36_V48_PR088/EDC16C36_V50_PR088/EDC16C36_V54_PR088/
EDC16C36_V58_PR088EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-303
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR089VEHICLE SPEED
PARAMETER
DEFINITIONGives the vehicle speed in km/h.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
This parameter is transmitted by the ABS computer. This signal is transmitted to the
injection on the multiplex network.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
In the event of a fault, carry out a multiplex network test (see 88B, Multiplexing)
And then full fault-finding on the ABS computer (see 38C, Anti-lock braking system).
EDC16C36_V44_PR089/EDC16C36_V4C_PR089/EDC16C36_V48_PR089/EDC16C36_V50_PR089/EDC16C36_V54_PR089/
EDC16C36_V58_PR089EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-304
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR128FIRST EGR VALVE OFFSET
PARAMETER
DEFINITIONThis parameter indicates the closing ratio of the EGR valve for the first offset of the EGR
valve.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
Indicates the percentage ≈ 20%.
PR128≈PR129 Last EGR valve offset, these 2 values should be similar.
In the event of a fault, consult the interpretation of faults DF209 EGR valve position sensor circuit and DF647
EGR valve position regulation.
EDC16C36_V44_PR128/EDC16C36_V4C_PR128/EDC16C36_V48_PR128/EDC16C36_V50_PR128/EDC16C36_V54_PR128/
EDC16C36_V58_PR128EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-305V9 MR-372-J84-13B450$152.mif
13B
PR129LAST EGR VALVE OFFSET
PARAMETER
DEFINITIONThis parameter indicates the EGR valve closing ratio for the last EGR valve offset.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C
Indicates the percentage ≈ 20%.
PR128 First EGR valve offset ≈ PR129, these 2 values should be similar.
In the event of a fault, see the interpretation of faults DF209 EGR valve position sensor circuit and DF647 EGR
valve position regulation.
EDC16C36_V44_PR129/EDC16C36_V4C_PR129/EDC16C36_V48_PR129/EDC16C36_V50_PR129/EDC16C36_V54_PR129/
EDC16C36_V58_PR129
DIESEL INJECTION
Fault finding – Interpretation of parameters
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-306V9 MR-372-J84-13B450$152.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR130CRUISE CONTROL SETPOINT
PARAMETER
DEFINITIONThis parameter indicates the cruise control setpoint.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
No faults must be present.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– or after a customer complaint (lack of power, smoke etc.).
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C
Indicates the cruise control cruising speed.
Cruise control can only be activated for a speed.
V > 18 mph (30 km/h)
EDC16C36_V44_PR130/EDC16C36_V4C_PR130/EDC16C36_V48_PR130/EDC16C36_V50_PR130/EDC16C36_V54_PR130/
EDC16C36_V58_PR130
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58