air filter RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 Repair Manual

13B-355
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC017PARTICLE FILTER REGENERATION
NOTESOnly run this command after interpretation of the following faults:
– DF308 Clogged particle filter,
– DF311 Failed regenerations limit exceeded,
– DF312 Speed request.
WARNING
It is essential to observe the health and safety regulations (see MR364 (Megane II ph2), MR370 (Scenic II
ph2), Mechanical, 19B, Exhaust, Particle filter: Cleaning) and observe the following procedure.
SAFETY INSTRUCTIONS TO BE FOLLOWED:
The regeneration causes exhaust fumes and high temperatures.
The vehicle must be outside during regeneration.
If it is not possible to carry out regeneration outside, use an extractor fan that can withstand the very high
regeneration temperatures (400°C at the exhaust outlet).
Perform regeneration on a surface free from fire risks (oil, dry leaves, etc.). Nothing should be left in the vicinity
of the exhaust pipe.
IMPORTANT
– Check the engine oil level before running the command to avoid any engine racing. The oil level must
be between the minimum threshold and the middle level on the oil dipstick.
– Before performing a particle filter regeneration, it is essential to deactivate the air conditioning
compressor (risk of engine damage) and all the electrical consumers.
IF NECESSARY:
Regeneration can be stopped by briefly pressing the vehicle start button twice (less than 3 seconds).
Switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes) Communication lost
with computer: EDC16C36, check the tool connection and the computer supply. before switching on the
ignition again.
PROCEDURE TO BE FOLLOWED:
Before a particle filter regeneration, check that there are no leaks or blockages in the exhaust pipe,
Repair if necessary
To run this command, select the command mode on the diagnostic tool, and select command SC017 Particle
filter regeneration.
When regeneration is complete, a message will indicate whether regeneration was successful, and what
operations need to be carried out (filter replacement, whether an oil service is required, etc.).
EDC16C36_V48_SC017/EDC16C36_V50_SC017/EDC16C36_V58_SC017EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-356
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC017
CONTINUED 1
DESCRIPTION OF THE PROCESS
Particle filter regeneration takes place in 3 stages (values given as a guide only):
–Heating phase: the engine speed is fixed or fluctuating around 2000 rpm.
This phase lasts between 8 and 14 minutes, until the coolant temperature exceeds 70°C.
–Regeneration phase: the speed is fixed or varies around 2000 rpm. Engine injection is retarded. The exhaust
fumes rise in temperature and burn the soot retained in the particle filter. Then the combustion of the soot stored
in the particle filter causes the particle filter upstream temperature to increase, possibly reaching 600°C
depending on the amount of soot in the particle filter. This phase lasts 28 minutes.
–Cooling phase: the engine speed decreases to 1250 rpm then increases to 1750 rpm.
Engine injection returns to normal and the exhaust gases cool the particle filter.
This phase lasts 3 minutes.
The procedure lasts at least 40 minutes, and varies depending on the time taken to reach a coolant temperature
of 70°C.
VALIDATING THE REGENERATION PROCESS:
At the end of regeneration, a message appears to announce whether the regeneration was successful:
●Particle filter regeneration finished:
Consult PR1012 Weight of soot after regeneration. If PR1012 is less than 15 g, the particle filter regeneration
completed correctly. If PR1012 is greater than 15 g, a second particle filter regeneration must be performed using
the command in the diagnostic tool and choose command SC017.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-357
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC017
CONTINUED 2
IMPORTANT:
Before performing a second After-Sales regeneration of the particle filter, the engine must be allowed to cool down
for 2 hours with the bonnet open.
Do not carry out the usual engine oil change before a second After-Sales regeneration.
Only for Vdiag 50:
– Change the engine oil if a message on the instrument panel requests it.
For the other VDiag:
–Consult PR848 Number of regeneration failures. If PR848 is greater than 3, change the engine oil.
●Particle filter too full - replace the particle filter: regeneration has failed. The weight of soot in the particle
filter is so great that it is creating back-pressure. Deal with any faults that appear or replace the particle filter.
Run command SC036 Reinitialise programming and select After particle filter replacement.
– Switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes): Communication
lost with computer: EDC16C36, check the tool connection and computer power supply.
–Then switch on the ignition again, clear the present or stored faults from the computer memory (operation
to be carried out within 3 minutes of switching on the ignition).
– Check the weight of soot: PR383 Weight of soot in the particle filter.
– If PR383
≥ 1 g. Apply the procedure of test 12 Manual clearing of the weight of soot.
Only for Vdiag 50:
– Change the engine oil if a message on the instrument panel requests it.
– For the other Vdiags:
–Consult PR848 Number of regeneration failures. If this parameter is greater than 3, it is essential to change
the engine oil.
– Explain to the customer the procedure for regeneration when driving to avoid unnecessary repairs: see PART D
in the interpretation of DF312 Speed request.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-358
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC017
CONTINUED 3
●Particle filter regeneration failed - run test Temperature upstream of turbine too low: regeneration has
failed because the temperature upstream of the turbine is too low. Run Test 8 Temperature upstream of
turbine too low.
In all cases, carry out the following operations:
– switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes): Communication
lost with computer: EDC16C36, check the tool connection and the computer supply.
– switch on the ignition and establish dialogue with the injection computer,
– run command SC036 Reinitialise programming,
– depending on the operation performed, select After particle filter regeneration with diagnostic tool, or After
particle filter replacement
– switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes): Communication
lost with computer: EDC16C36, check the tool connection and the computer supply.
–Then switch on the ignition again, clear the present or stored faults from the computer memory (operation
to be carried out within 3 minutes of switching on the ignition).
– Check the weight of soot: PR383 Weight of soot in the particle filter.
– If PR383
≥ 1 g. Apply test procedure 12 Manual clearing of the weight of soot.
If DF308 Particle filter clogged or DF312 Speed request is still present, contact Techline.
Note:
It is essential to change the engine oil and the oil filter in the following cases:
– following an After-Sales regeneration only if a message on the CLIP diagnostic tool requests it,
– following particle filter replacement,
after a second regeneration (when two successive regenerations).
EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-362
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC035
CONTINUED
Explanation of results interpretation:
Check 1:
– Use scenario SC031: Operational fault finding of cylinders.
–For VDiag 44, run Test 10 Poor injector operation.
–Apply ALP6 Fuel circuit external leaks.
–Run Test 3 Low pressure circuit check.
– Replace the high pressure pump.
Check 2:
– Use scenario SC031: Operational fault finding of cylinders.
–For VDiag 44, run Test 10 Poor injector operation.
–Apply ALP6 Fuel circuit external leaks.
– Run the part of Test 3 Low pressure circuit check which concerns the fuel filter.
– Replace the high pressure pump.
– Check the injector return flow and the injectors, run Test 10 Poor injector operation.
– Check the rail pressure regulator by running command AC011 “Rail pressure regulator”.
Check 3:
– Use scenario SC031: Operational fault finding of cylinders.
–For VDiag 44, run Test 10 Poor injector operation.
–Apply ALP6 Fuel circuit external leaks.
–Run Test 3 Low pressure circuit check.
– Replace the high pressure pump.
Check 4:
Replace the high pressure pump.
Check 5:
– Check the injector return flow and the injectors (run Test 10 Poor injector operation).
– Check the rail pressure regulator by running command AC011 “Rail pressure regulator”.
Consult the repair manual for the various checks (from 1 to 5), see MR 364 (Mégane II ph2), MR 370 (Scénic II
ph2), Mechanical, 13B, Diesel injection, Injector rail, Removal - Refitting.
Repair if necessary.
EDC16 C36
Program No.: 91
Vdiag No.: 4C, 48, 50,
54, 58

13B-363
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC036REINITIALISE PROGRAMMING
NOTESThis command is used to reset the computer parameters according to the type of
operation or component repaired or replaced from the following list:
– the injectors
– the EGR valve,
– the damper valve,
– after particle filter replacement (Vdiag 48, 50 only),
– after particle filter regeneration with the diagnostic tool (VDiag 48, 50 only),
– after replacing the injection computer with no save option (VDiag 48, 50 only).
Ignition on and engine stopped.
To run this command, in the CLIP tool, select scenario SC036 Reinitialise programming.
Procedure to be followed:
– on the main screen, select the component to reinitialise after a mechanical operation (removal - refitting or
replacement of component),
–select YES then OK to begin reinitialisation,
–select end on the configuration completed screen to return to the main screen,
– switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes): Communication
lost with computer: EDC16 C36, check the tool connection and the computer supply. before switching on
the ignition again.
End of procedure.
EDC16C36_V44_SC036/EDC16C36_V4C_SC036/EDC16C36_V48_SC036/EDC16C36_V50_SC036/EDC16C36_V54_SC036/
EDC16C36_V58_SC036EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-364
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC036
CONTINUED
Features of the selections: After particle filter regeneration with diagnostic tool and After replacement of the
particle filter:
After using one of these 2 commands:
– switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes): Communication
lost with computer: EDC16C36, check the tool connection and computer power supply.
–Then switch on the ignition again and clear the present or stored faults from the computer memory
(operation to be carried out within 3 minutes of switching on the ignition).
– Check the weight of soot: PR383 Weight of soot in the particle filter.
– If PR383
≥ 1 g. Apply test procedure 12 Manual clearing of the weight of soot.
IMPORTANT
When reinitialising injectors, do not forget that cylinder no. 1 is located at the flywheel end.

13B-370
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC011
CONTINUED
Step 2
In the event of rail overpressure:
Check that there are no air bubbles in the diesel fuel low pressure circuit.
Check that the rail pressure sensor is operating correctly.
Consult the interpretation of parameter PR038 Rail pressure.
If these checks reveal no irregularities, replace the regulator.
in the event of rail underpressure:
Check that the rail pressure sensor is operating correctly.
Consult the interpretation of parameter PR038 Rail pressure.
Check the low pressure diesel circuit priming.
Check the conformity of the diesel filter connections.
Check the condition of the filter (clogging and water saturation).
Check that there are no air bubbles between the filter and the high pressure pump.
Check the sealing of the low and high pressure diesel fuel systems: use ALP6 Fuel circuit leaks (visual
inspections, touch tests, odours, etc.) on:
pump body, pressure release valve, pipes, rail and injectors unions, injector wells, etc.
Check the conformity of the seal fitting on the pressure regulator.
Check the operation of the injectors, run Test 10 Poor injector operation.
Carry out the necessary repairs.
If the engine starts:
Clear any faults.
Check the pressure regulator by applying (see ALP7 Rough idle).
With the engine warm, leave it to idle for a few minutes (3 to 5 minutes):
– If it stalls and the fault reappears, replace the regulator.
– If it does not stall, stabilise the engine speed at 2000 rpm(1 minute) then accelerate at full load until it cuts out.
If the engine stalls, contact the Techline
If the engine does not startor there is no timing:
first, replace the regulator and if the fault is still present, contact the Techline.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-386
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
V9 MR-372-J84-13B450$190.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP4 Poor performance
NOTESBefore analysing this customer complaint, check that there are no faults, and the
conformity (or otherwise) of the parameters and statuses, using the diagnostic
tool.
If the customer complaint is not eliminated, perform the following checks.
IMPORTANT
In the case of engine overheating to above 118°C, the computer deliberately limits the fuel flow (overheating
warning light lights up from 115°C).
Please observe the cleanliness guidelines and safety advice.
Is the poor performance accompanied by smoke?
Check the conformity of the fuel used by running test 11 Diesel fuel conformity check.
If the diesel fuel is not correct:
– Replace the diesel fuel.
– Change the diesel filter.
– Bleed the low and high pressure diesel circuit.
Test the high pressure fuel circuit:
Run the scenario SC035 High pressure fuel circuit fault finding (see Interpretation of commands).
Check that the injectors are correctly fitted (presence and conformity of the sealing washer).
Checking procedure:
– Take a straightedge approximately 40 cm long and place it on the 4 injectors. The straightedge should rest on
the 4 injectors.
– If 1 injector protrudes, remove the injector and check that the washer is correct.
– If one injector does not touch the straightedge (clearance of more than 1 mm), remove the injector and check
that the washer is present.
– Clean the injector wells and the injector, refit the injector with the correct sealing washer.
– The tightness seal and the condition of the inlet circuit: run test 4: Turbocharged air inlet circuit check.
– The condition of the air flowmeter, run test 5 Air flowmeter.
– The turbocharger, run the following tests:
– test 2: Air path at the turbocharger,
– test 6: Turbocharger control solenoid valve check,
– test 7: Turbocharger.
NOA
YES
EDC16C36_V44_ALP04/EDC16C36_V4C_ALP04/EDC16C36_V48_ALP04/EDC16C36_V50_ALP04/EDC16C36_V54_ALP04/
EDC16C36_V58_ALP04EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-387
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
V9 MR-372-J84-13B450$190.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP4
CONTINUED
is the engine running on all cylinders?
Check the operation of the injectors, run test 10 Poor injector operation.
If the fault is still present
Check the conformity of the accelerator pedal position sensor, the brake pedal sensor, the atmospheric pressure
sensor, the exhaust gas recirculation valve, and the damper valve (see Interpretation of statuses and
Interpretation of parameters).
Check the consistency of the signal for the air flowmeter, the engine coolant temperature sensor, the fuel
temperature sensor and the engine speed.
Check the connectors, the continuity, and the absence of interference resistance of the air flowmeter (apply DF056
Air flow sensor circuit), the engine coolant temperature sensor (apply DF001 Coolant temperature circuit), the
fuel temperature sensor (apply DF098 Fuel temperature sensor circuit), and the engine speed (apply DF195
Camshaft sensor - engine speed consistency).
Check:
– That the diesel filter is not clogged.
– That there are no leaks on the high and low pressure diesel circuits: run test 3 Low pressure circuit check.
– The connection of the oil vapour rebreathing circuit.
– The rail pressure regulator (MPROP) (jammed - stuck), apply the interpretation of command AC011 Rail
pressure regulator.
Check the engine timing (and the position of the high pressure pump sprocket). See the procedure in the
Workshop Repair Manual if necessary.
Test the high pressure fuel circuit:
Run the scenario SC035 High pressure fuel circuit fault finding (see Interpretation of commands).
If the fault is still present, contact the techline.
A
NO
YES
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58