brake light RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 Workshop Manual

13B-37V9 MR-372-J84-13B450$090.mif
DIESEL INJECTION
Fault finding – Fault summary table13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
Management of instrument panel warning lights according to the faults notified.
*temp: temperatureFaultDTC code in
hexadecimalLevel 1 fault
warning light
(orange
SERVICE
warning light)Level 2 fault
warning light
(red STOP
warning light)No fault
warning
light litOBD
warning
light lit
DF200 Atmospheric pressure
sensor2226 1.DEF/2.DEF - -1.DEF/
2.DEF
DF209 EGR valve position
sensor circuit409 - - CC.1/CO.0CC.1/
CO.0
DF221 Clutch contact signal 830 - - 1.DEF -
DF226 Damper valve circuit 120CO/CC.0/CC.1/
CC/1.DEF/
2.DEF-3.DEF-
DF228 Brake signal 571 - -1.DEF/
2.DEF-
DF232 Coolant pressure
sensor circuit530 - - CC.0/CO.1CC.0/
CO.1
DF249 Injector control 62B - 1.DEF - -
DF272 EGR valve control
circuit487 - -CO/CC.1/
CC.0/CCCO/CC.1/
CC.0/CC
DF276 Injector code
programming611 1.DEF/2.DEF - - -
DF293 Water in diesel fuel
detector2269 - - 1.DEF -
DF308 Clogged particle filter 242F X - - -
DF309 Particle filter
downstream temp* sensor242A - - CO.1/CC.0 -
DF310 Particle filter upstream
temp* sensor2031 CO.1/CC.0 - -CO.1/
CC.0
DF311 Number of failed
regenerations exceeded1435 X - - -

13B-125
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check using the diagnostic tool.
V9 MR-372-J84-13B450$103.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF165
PRESENT
OR
STOREDACCELERATOR PEDAL POSITION SENSOR CIRCUIT
1.DEF: No signal
2.DEF: Accelerator pedal sensor locked
3.DEF: Detection of accelerator pedal depressed at same time as brake pedal.
1.DEF
2.DEF
NOTESPriorities when dealing with a number of faults:
Deal with fault DF012 Sensor supply no. 2 voltage first, if
it is present or stored.
Conditions for applying the fault finding procedure to a
stored fault:
The fault occurs if the brake pedal and the accelerator pedal
are depressed simultaneously for more than 1 second.
Special notes:
If the fault is present,
–the level 2 warning light illuminates if 1.DEF or 2.DEF is
present,
– turbocharging and cruise control are not authorised,
– the engine speed is fixed at 1400 rpm,
– cruise control/speed limiter function unusable,
– limitation of the quantity of fuel injected.
Use bornier Elé.1681 for any operations on the computer
connectors.
Use Wiring Diagram Technical Note, Mégane II ph2,
Scénic II ph2.
EDC16C36_V44_DF165/EDC16C36_V4C_DF165/EDC16C36_V48_DF165/EDC16C36_V50_DF165/EDC16C36_V54_DF165/
EDC16C36_V58_DF165EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-254V9 MR-372-J84-13B450$132.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET704
ET705
CONTINUED
Sensor electrical conformity
ACTIVE
or
INACTIVEIf the brake lights are working:
check the continuity and the absence of interference resistance on the following
connection:
– Connection code 5A between components 160 and 120/645/119.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
If the brake lights are not operational, check:
– the condition and fitting of the brake switch,
– the status and conformity of the fuse for the brake lights.
– the conformity of the values in the following table:
Disconnect the switch and carry out the following checks:
for MEGANE II and SCENIC II with ESP
Continuity between
connectionsInsulation between
connections
Switch engaged
(Brake pedal released)5A and BPT 65G and SP17
Switch released
(Brake pedal
depressed)65G and SP17 5A and BPT
Replace the switch if the values obtained are not correct.
For MEGANE II and SCENIC II without ESP
Continuity between
connectionsInsulation between
connections
Switch engaged
(Brake pedal released)5A and BPT 65A and SP17
Switch released
(Brake pedal
depressed)65A and SP17 5A and BPT
Replace the switch if the values obtained are not correct.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58