Particle filter injector RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Siemens Injection Owner's Manual

13B-259
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
AC037: Preheating relay.
Activating this lets you listen to the operation of the preheating relay and enables the warning light in the
instrument panel to be illuminated.
AC079: Static actuator test.
Activating this allows you to activate the injection system actuators (simultaneously runs commands
AC003, AC005 to AC008, AC012, AC037, AC213, and AC214).
Run this command with the engine stopped and the engine coolant temperature below 40°C.
AC099: Inhibition of electrical consumers.
AC100: Cancel inhibition of electrical consumers.
AC213: Fuel flow solenoid valve.
AC214: Turbocharger control solenoid valve.
Activating this allows you to listen to the operation of the turbocharger control solenoid valve.
AC233: Thermoplungers no. 1 and no. 2 (Vdiag 45, 49 and 4D only).
AC234: Thermoplunger no. 3 (Vdiag 45, 49 and 4D only).
AC235: Thermoplunger no. 4 (Vdiag 45, 49 and 4D only).
AC236: Coolant pump relay (only for vehicles equipped with a particle filter, except KANGOO II).
AC237: Fuel pump relay (only for vehicles equipped with a particle filter).
Activating this allows you to check the sealing on the 5
th particle filter injector circuit.
AC238: Particle filter injector (Only for vehicles equipped with a particle filter).
AC239: Particle filter temperature sensor fault finding (only for vehicles equipped with a particle filter).
Run this command with the engine stopped and the engine coolant temperature below 40°C.
AC260: Thermoplunger relay.
Activating this allows you to check the three thermoplunger relays.

13B-262
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
SC017
PARTICLE FILTER REGENERATION
NOTESCarry out this command only under the following conditions:
– DF308 Clogged particle filter present.
Ignition on and engine stopped.
Vdiag 45, 49 and 4D only.
WARNING:
–It is essential to carry out the next procedure in accordance with the safety and cleanliness guidelines,
(see MR 364 (Mégane II), 370 (Scénic II), 417 (Kangoo II), 385 (Modus), 392 (Clio III), Mechanical, 19B,
Exhaust, Particle filter: Cleaning).
– do not run command AC029 High pressure circuit seal test until regeneration has finished.
– before each regeneration, check the fuel level,
– before and after each regeneration, check the oil level.
With the engine running and the vehicle stopped, this function allows the particle filter to be regenerated.
Safety instructions to be followed:
The regeneration causes exhaust fumes and high temperatures.
The vehicle must be outside during regeneration.
If it is not possible to carry out regeneration outside, check that the extractor fan can withstand the very high
regeneration temperatures.
Perform regeneration on a surface free from fire risks (oil, dry leaves, etc.).
Nothing should be left in the vicinity of the exhaust pipe.
Before regeneration:
– Respect After-Sales recommendations for particle filter regeneration.
– Check the oil level to prevent the engine from racing.
– Check the fuel level.
– Check the sealing on the 5th particle filter injector circuit using actuator AC237 Fuel pump relay.
– Check that there are no leaks or blockages in the exhaust pipe,
To perform regeneration:
– Vehicle stopped and in neutral.
– Engine running and warm.
– No pedal depressed (accelerator and clutch).
– No faults present preventing regeneration from being carried out on the system.
– No leak in the 5th particle filter injector circuit.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V45_SC017 / SID304_V49_SC017 / SID304_V4D_SC017 / SID301_V4C_SC017

13B-278
MR-372-J84-13B050$897.mif
V17
DIESEL INJECTION
Fault finding – Fault Finding Chart
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
ALP 6 Engine idle speed too low or unstable
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check the presence and conformity of the fuel by running Test 13 Diesel fuel conformity check.
Check the injection computer: that the connections and wiring are in good condition, that earths and feeds are
present.
If the wiring is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check the air inlet circuit (refer to the interpretation of fault DF301 Air inlet circuit).
Check that the damper valve operates correctly (refer to the interpretation of fault DF641 Damper valve circuit).
Check the air flowmeter (refer to the interpretation of faults DF039 Inlet air temperature sensor circuit, DF129
Air flow requested and DF056 Air flow sensor circuit).
Check the air conditioning pressure sensor (refer to the interpretation of fault DF049 Refrigerant sensor circuit).
If the wiring is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If fault DF308 Particle filter clogged is present, replace the particle filter.
Run command RZ030 Particle filter adaptives after replacing the particle filter.
Check the low pressure fuel supply system by performing test 1 Low pressure supply check and test 2
Internal fuel transfer pump (ITP) check.
Check the high pressure fuel supply system by performing test 3 High pressure fuel pressure solenoid valve
check, test 4 High pressure pump (HPP) and fuel flow solenoid valve check and test 5 Rail high pressure
regulation circuit check.
Check the injectors by performing test 6 Major injector leak/injectors open and test 7 Incorrect injection
amount.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
SID301_V44_ALP6 / SID304_V45_ALP6 / SID301_V48_ALP6 / SID304_V49_ALP6 / SID304_V4D_ALP6 / SID301_V4C_ALP6

13B-296
MR-372-J84-13B050$897.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Fault Finding Chart13B
ALP 20 Exhaust fumes
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Is the vehicle equipped with a particle filter?
(Vdiag 45, 49 and 4D only)
NO
Check the engine oil grade and level.
Check the presence and conformity of the fuel, by running Test 13 Diesel fuel conformity check, and its circuit
(see MR 385, 392, 364, 370 or 417, Mechanical, 13A, Fuel supply).
Check the cooling system (see MR 385 392 364, 370 or 417 Mechanics, 19A, Cooling, Engine cooling system:
Specifications).
Check the fuel temperature sensor (refer to the interpretation of Fuel temperature sensor circuit faults DF098).
Check the coolant temperature sensor (refer to the interpretation of faults DF001 Coolant temperature sensor
circuit).
Check the air inlet circuit (refer to the interpretation of fault DF301 Air inlet circuit).
Check that the damper valve operates correctly (refer to the interpretation of fault DF641 Damper valve circuit).
Check the air flowmeter (refer to the interpretation of faults DF039 Inlet air temperature sensor circuit, DF129 Air
flow requested and DF056 Air flow sensor circuit).
Check the turbocharging pressure (consult the interpretation of fault DF004 Turbocharging pressure sensor circuit).
Check the preheating system (refer to the interpretation of fault DF025 Preheating unit diagnostic line).
Check the injection computer: that the connections and wiring are in good condition, that earths and feeds are present.
If the wiring is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
YES
Deal with the following faults first: DF238
Thermoplunger no. 3 relay circuit, DF239
Thermoplunger no. 2 relay circuit, DF240
Thermoplunger no. 1 relay circuit and DF1005
Thermoplunger control unit fault finding 1
connection. Check the particle filter injector supply
circuit, by running Test 8 Checking the particle filter
injector supply circuit.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
SID301_V44_ALP20 / SID304_V45_ALP20 / SID301_V48_ALP20 / SID304_V49_ALP20 / SID304_V4D_ALP20 / SID301_V4C_ALP20
A

13B-300
MR-372-J84-13B050$897.mif
V17
DIESEL INJECTION
Fault finding – Fault Finding Chart
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
ALP 21
CONTINUED 2
Check the air flow:
●The air flow must be approximately 250 mg/st.
Check the air flowmeter connector, component code 799 (corrosion, fouling, etc.).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the continuity, insulation and absence of interference resistance on the following connections:
●Code connection 3FB (3FB3 for Kangoo II) between components 799 and 1768.
●Connection code 3ABQ between components 799 and 120.
●Connection code 3DV between components 799 and 120.
●Connection code 3KJ between components 799 and 120.
●connection code 3DW between components 799 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the particle filter injector supply system by running Test 8 Particle filter injector supply circuit check.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.

13B-301
MR-372-J84-13B050$936.mif
V17
13B
DIESEL INJECTION
Fault finding – Tests
Some special checks are grouped under the heading Tests and are used as required in different fault
finding charts (ALP) or interpretation of faults.
*Technical Note 3419: Fault finding on the turbocharger for petrol and diesel engines
NOTESOnly consult these tests when dealing with a fault finding chart (ALP) or when
interpreting faults.
Low pressure fuel supply system check. TEST 1
Internal fuel transfer pump (ITP) check. TEST 2
High pressure fuel pressure solenoid valve check. TEST 3
Check high-pressure pump (HPP) and fuel flow solenoid valve. TEST 4
Rail high pressure control circuit check. TEST 5
Major leak in injectors/injectors open. TEST 6
Incorrect injection quantity. TEST 7
Particle filter injector supply circuit check.
Only for Vdiag 45, 49 and 4D.TEST 8
Particle filter history.
Only for Vdiag 45, 49 and 4D.TEST 9
Turbocharger air chain. TEST 10
Turbocharger control solenoid valve.TEST 11: Apply
TEST 4 of
Technical Note
3419*
Turbocharger.TEST 12: Apply
TEST 7 of
Technical Note
3419*
Diesel fuel conformity check. TEST 13
MR-372-J84-13B050$936.mif
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4CProgram No.: B1 and B2

13B-318
MR-372-J84-13B050$936.mif
V17
DIESEL INJECTION
Fault finding – Tests13B
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
TEST 8 Particle filter injector supply circuit check
NOTESDeal first with faults DF991 Particle filter injector control circuit and DF1004
Electric fuel pump relay control circuit.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and Kangoo II Wiring
diagrams Technical Note.
Vdiag 45, 49 and 4D only.
Check the condition of the fuel supply pipes
between the particle filter injector and the electric
fuel pump.
Check that the pipes are not trapped, blocked or
pierced and there that are no leaks.
Are the components in good condition?
YES
Check the particle filter injector, component
code 1750.
Check the condition, power feed and
connections of the particle filter injector.
(Consult the interpretation of fault DF991
Particle filter injector control circuit). Check it
works by running command AC238 Particle
filter injector.
Does the particle filter injector operate
correctly?
YES
NOReplace any faulty components.
NOReplace the particle filter injector if
necessary.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
SID304_V45_TEST8 / SID304_V49_TEST8 / SID304_V4D_TEST8 / SID301_V4C_TEST8
A

13B-319
MR-372-J84-13B050$936.mif
V17
DIESEL INJECTION
Fault finding – Tests
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
TEST 8
CONTINUED 1
Particle filter injector fuel system pressurisation check (pressure test):
To check the pressure in the particle filter injector fuel system:
●Connect the T-union Mot 1311-08 to the particle filter injector fuel filter outlet (adapter visible without
dismantling).
●Connect the pressure gauge Mot 1311-01 to the T-union.
Pressurise the fuel system using the diagnostic tool, and run command AC237 Fuel pump relay.
If the pressure in the system is about 1 bar, perform the command a second time.
The pressure must be at least 3 bar.
If the fuel pressure is less than 3 bar, proceed as follows:
●Carry out a visual inspection of the flexible supply hose to the particle filter injector, before and after the
T-union (leaks, pinching, fuel filter condition, etc.).
Pressurise the fuel system again with the diagnostic tool, and run command AC237 Fuel pump relay.
If the pressure is not equal to or above 3 bar, replace the pump/sender unit (see Technical Note 5117A, Special
features of vehicles fitted with the K9K 772 engine).
Checking the pressure regulator:
●Run command AC237 Fuel pump relay, until the fuel pressure reaches 5 bar.
●Reactivate command AC237 Fuel pump relay again to check that the pressure is controlled between 5.5 bar
and 5 bar.
If the regulator is not working, replace the pump/sender unit (see Technical Note 5117A, Special features of
vehicles fitted with the K9K 772 engine).
Note:
To reduce the pressure in the system, run command AC238 Particle filter injector, until it drops to 3 bar, then
carefully disconnect the union.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
A

13B-320
MR-372-J84-13B050$936.mif
V17
DIESEL INJECTION
Fault finding – Tests
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
TEST 8
CONTINUED 2
With + after ignition feed on, check for + 12 V feed between connection codes 3AHB and M at the electric pump
connector of the particle filter injector, component code 1767.
If there is no + 12 V feed to the sensor, check the continuity, insulation and absence of interference
resistance on the following connections:
●connection code 3AHB between components 1767 and 1768,
●Connection code M between component 1767 and the vehicle earth.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
(Refer to the interpretation of faults DF1004 Electric fuel pump relay control and DF1001 Particle filter
upstream temperature regulation).
●Reconnect or replace the pipe.
Repeat the pressure test.
●Replace the fuel filter (see MR 392, 385, 364, 370 and 417 Mechanics, 13A, Fuel supply, Fuel filter:
Removal - Refitting).
Repeat the pressure test.
●Replace the particle filter injector electric pump.
Repeat the pressure test.
●Check that the particle filter injector is fitted correctly.
Check that the particle filter injector is correctly held in place. Repair or replace the particle filter injector mounting.
●"Only on Kangoo 2:
Check the integrity and correct fitting of the evaporator plate located under the particle filter injector, at the level of
the bracket.
If the blade of the evaporator plate has become detached, it may be located downstream from the line between its
original position and the oxidation catalytic converter inlet.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.