instrument panel RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Siemens Injection Owner's Guide

13B-253
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR873
OIL OXIDATION SIGNAL
PARAMETER
DEFINITIONThis parameter indicates the vehicle mileage when the oil oxidation threshold is
reached.
NOTESOnly apply the interpretation of this parameter if the OCS (oil control system)
program is activated on the instrument panel. Check on the instrument panel computer
that the configuration reading LC106 O.C.S. is set to WITH.
Except Vdiag 44, 45 and 49.
Conformity check: Engine stopped and the ignition on, or the engine running and the engine coolant
temperature > 80°C, without electrical consumers
The oil status is calculated by the oxidation program in the injection computer, depending on the engine revs.
When this count reaches a certain threshold before the end of the oil change period, the injection computer sends
a signal to the instrument panel, which will display "service required soon". PR873 corresponds to the vehicle
distance at the time this signal is sent.
The instrument panel computer counts down 900 miles (1500 km) before displaying the message "service
required".
IMPORTANT
When the message "service required" appears on the instrument panel, the customer must arrange an oil
service within the remaining 900 miles (1500 km).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR873/SID301_V45_PR873/SID304_V49_PR873

13B-254
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR874
LAST SERVICE
PARAMETER
DEFINITIONThis parameter indicates the vehicle mileage at the last service carried out and is
updated when the oil service parameters are reset on the instrument panel or by pedal
sequence.
NOTESNone.
This parameter indicates the vehicle mileage at the last service carried out and is updated when the oil service
parameters are reset on the instrument panel or by pedal sequence.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V48_PR874/SID304_V4D_PR874/SID301_V4C_PR874

13B-255
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR875
OIL DILUTION SIGNAL
PARAMETER
DEFINITIONThis parameter indicates the vehicle mileage when the oil dilution threshold is reached.
NOTESThis parameter should be interpreted only if the OCS (Oil Control System) program
is activated on the instrument panel. On the instrument panel computer, check the
configuration reading LC106 O.C.S: WITH.
Except Vdiag 44, 45 and 49.
Conformity check: Engine stopped and the ignition on, or the engine running and the engine coolant
temperature > 80°C, without electrical consumers
The injection computer assesses the dilution rate of the engine oil according to the customer's driving style.
When the dilution level reaches a certain threshold before the end of the oil change interval, the injection
computer sends a signal to the instrument panel, which then displays Service required. Parameter PR875
corresponds to the vehicle mileage at the time this signal is sent.
IMPORTANT
When the message Service required appears on the instrument panel, the customer must arrange an immediate
oil change to prevent damage to the engine.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR875/SID304_V45_PR875/SID301_V4C_PR875

13B-259
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
AC037: Preheating relay.
Activating this lets you listen to the operation of the preheating relay and enables the warning light in the
instrument panel to be illuminated.
AC079: Static actuator test.
Activating this allows you to activate the injection system actuators (simultaneously runs commands
AC003, AC005 to AC008, AC012, AC037, AC213, and AC214).
Run this command with the engine stopped and the engine coolant temperature below 40°C.
AC099: Inhibition of electrical consumers.
AC100: Cancel inhibition of electrical consumers.
AC213: Fuel flow solenoid valve.
AC214: Turbocharger control solenoid valve.
Activating this allows you to listen to the operation of the turbocharger control solenoid valve.
AC233: Thermoplungers no. 1 and no. 2 (Vdiag 45, 49 and 4D only).
AC234: Thermoplunger no. 3 (Vdiag 45, 49 and 4D only).
AC235: Thermoplunger no. 4 (Vdiag 45, 49 and 4D only).
AC236: Coolant pump relay (only for vehicles equipped with a particle filter, except KANGOO II).
AC237: Fuel pump relay (only for vehicles equipped with a particle filter).
Activating this allows you to check the sealing on the 5
th particle filter injector circuit.
AC238: Particle filter injector (Only for vehicles equipped with a particle filter).
AC239: Particle filter temperature sensor fault finding (only for vehicles equipped with a particle filter).
Run this command with the engine stopped and the engine coolant temperature below 40°C.
AC260: Thermoplunger relay.
Activating this allows you to check the three thermoplunger relays.

13B-264
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
SC040
SPEED LIMITER
NOTESThis command enables the vehicle speed restriction to be modified.
KANGOO II only.
To run this command, select scenario SC040 Speed limiter in the CLIP diagnostic tool.
This command allows you to:
– read the vehicle's restricted speed,
– activate the speed restriction at a predefined speed,
– deactivate or change the current restricted speed set on the vehicle.
IMPORTANT
If the vehicle is restricted, the driver of the vehicle must be informed. Consequently, in accordance with the
regulations, the vehicle speed restriction should be shown on a label on the instrument panel.
The label should be changed when any changes to the speed restriction are introduced.
Use statuses ET741 Optional speed restriction and PR879 Maximum authorised speed to check if the
command has been recognised.
The speed restrictions are between 18 mph (30 km/h) < X < 150 mph (250 km/h).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_SC040 / SID304_V48_SC040 / SID301_V4C_SC040

13B-324
MR-372-J84-13B050$936.mif
V17
DIESEL INJECTION
Fault finding – Tests
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
TEST 9
CONTINUED 3
SECTION D - Procedure for switching off the particle filter message or warning light on the instrument panel
Certain types of driving can trigger the activation of the particle filter warning light or message. This fault occurs
when the weight of soot is more than 30.8 g.
The customer must carry out a specific driving operation (cf. vehicle user manual) that consists of:
1. Making sure the engine is warm
2. Drive at a speed greater than 24 mph (40 km/h) for 2 minutes to initiate the regeneration process.
Initiating regeneration Minimum speed Minimum time
All vehicle types 24 mph (40 km/h) 2 minutes
3. Then drive at a speed of more than 24 mph (40 km/h) until the Particle Filter message or warning light on the
instrument panel goes out. In order for the procedure to succeed, it is necessary to drive without stopping
(without stopping the engine) or to leave the engine running at idle speed for an extended period of time. The
regeneration time depends on the vehicle and driving conditions but normally lasts about 20 minutes.
Regeneration duration Minimum speed Average time
All vehicle types 24 mph (40 km/h) 20 minutes
4. If regeneration when driving fails (the warning light has not switched off or the service warning light has come
on), carry out a particle filter regeneration in the Renault dealership. To carry out After-Sales regeneration:
check the oil level and remove some oil if the maximum level has been reached, then apply the procedure for
command SC017 Particle filter regeneration (see Interpretation of commands).
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.