warning light RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Siemens Injection Repair Manual

13B-135
MR-372-J84-13B050$585.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET028
LEVEL 1 FAULT WARNING LIGHT REQUEST
STATUS DEFINITION"ACTIVE": This status indicates that the Level 1 fault warning light request is active.
"INACTIVE": This status indicates that the Level 1 fault warning light request is not
active.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C
ACTIVE
The injection computer has detected one or more faults.
Deal with these faults (see interpretation of faults).
INACTIVEThe status is "INACTIVE" when the injection computer has not detected any fault which
may cause the level 1 warning light to come on.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET028/SID304_V45_ET028/SID301_V48_ET028/SID304_V49_ET028/SID304_V4D_ET028/SID301_V4C_ET028

13B-136
MR-372-J84-13B050$585.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET029
LEVEL 2 FAULT WARNING LIGHT REQUEST
STATUS DEFINITION"ACTIVE": This status indicates that the Level 2 fault warning light request is active.
"INACTIVE": This status indicates that the Level 2 fault warning light request is not
active.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C
ACTIVE
The injection computer has detected one or more faults.
Deal with these faults (see interpretation of faults)
INACTIVEThe status is "INACTIVE" when the injection computer has not detected any fault which
may cause the level 2 warning light to come on.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET029/SID304_V45_ET029/SID301_V48_ET029/SID304_V49_ET029/SID304_V4D_ET029/SID301_V4C_ET029

13B-155
MR-372-J84-13B050$585.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET148
OBD WARNING LIGHT ACTIVATION REQUEST
STATUS DEFINITION"OFF": This status indicates that the OBD warning light activation request is not
active.
"ON": This status indicates that the OBD warning light activation request is active.
"FLASHING": This status indicates that OBD warning light activation request is
alternating.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C
OFF
The status is "OFF" when no fault associated with the antipollution system is present or
stored.
ONThe status is "ON" when one or more faults associated with the antipollution system is
present or stored.
Consult the fault summary table to determine the faults associated with activation of the
OBD warning light.
Interpret the present or stored faults.
FLASHINGNONE
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET148/SID304_V45_ET148/SID301_V48_ET148/SID304_V49_ET148/SID304_V4D_ET148/SID301_V4C_ET148

13B-183
MR-372-J84-13B050$624.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET706
ET707
ET708
ET709
ET710
ET711
ET712
ET713
ET714
ET715STORED ENGINE STATUS NO. 1
STORED ENGINE STATUS NO. 2
STORED ENGINE STATUS NO. 3
STORED ENGINE STATUS NO. 4
STORED ENGINE STATUS NO. 5
STORED ENGINE STATUS NO. 6
STORED ENGINE STATUS NO. 7
STORED ENGINE STATUS NO. 8
STORED ENGINE STATUS NO. 9
STORED ENGINE STATUS NO. 10
STATUS DEFINITIONRUNNING: This status indicates that the stored engine status is engine running.
STOPPED: This status indicates that the stored engine status is engine stopped.
NOTESSpecial note:
Check the interpretation of these parameters only on ALP21 Particle filter warning
light illuminated.
Vdiag 4D and 49 only.
Each STATUS between ET706 and ET715 corresponds to regeneration failures for which the mileage is recorded
by the parameters PR794 Regeneration failure record No. 1 to PR803 Regeneration failure record No. 10
(for example: PR797 Regeneration failure record No. 4 is linked to ET709 Stored engine status no. 4).
"RUNNING"
The status is ACTIVE as soon as the ignition is switched on.
"STOPPED"If the status is STOPPED, regeneration failure due to the engine being switched off.
+ APCDo not interpret this engine status.
"NONE"Do not interpret this engine status.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID304_V4D_ET706/SID304_V4D_ET707/SID304_V4D_ET708/SID304_V4D_ET709/SID304_V4D_ET710/SID304_V4D_ET711/
SID304_V4D_ET712/SID304_V4D_ET713/SID304_V4D_ET714/SID304_V4D_ET715/SID304_V49_ET706/SID304_V49_ET707/
SID304_V49_ET708/SID304_V49_ET709/SID304_V49_ET710/SID304_V49_ET711/SID304_V49_ET712/SID304_V49_ET713/
SID304_V49_ET714/SID304_V49_ET715/SID301_V4C_ET707/SID301_V4C_ET708/SID301_V4C_ET709/SID301_V4C_ET710/
SID301_V4C_ET711/SID301_V4C_ET712/SID301_V4C_ET713/SID301_V4C_ET714/SID301_V4C_ET715

13B-187
MR-372-J84-13B050$663.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Parameter summary table13B
Tool parameter Diagnostic tool title
PR125Power absorbed by the AC* compressor Vdiag 44 and 48 only
PR128First EGR valve offset
PR129Last EGR valve offset
PR130Cruise control setpoint
PR132Air flow
PR171Air flow setpoint for EGR Vdiag 44 and 48 only
PR190Engine idle speed setpoint.
PR224Turbocharging pressure sensor voltage Vdiag 44 and 48 only
PR228Injector control capacitor voltage
PR364Cylinder no. 1 fuel flow correction
PR365Cylinder no. 4 fuel flow correction
PR381Particle filter downstream temperature
Vdiag 4D, 45 and 49 only PR382Particle filter upstream temperature
PR383Weight of soot in the particle filter
PR391Mileage since particle filter replacement
PR400New EGR valve offset
PR405Cylinder no. 2 fuel flow correction
PR406Cylinder no. 3 fuel flow correction
PR412Mileage at last successful regeneration
Vdiag 4D, 45 and 49 only PR414Particle filter diff* pressure
PR415Time since last regeneration
PR513Mileage counter for level 1 warning light
PR514Mileage counter for level 2 warning light
PR634Air flow request
PR667Turbine upstream temperature
Vdiag 4D, 45 and 49 only PR668Turbine upstream temperature sensor voltage
PR669Particle filter diff* press* sens* voltage
PR670Particle filter upstream temp* sens* voltage
PR671Particle filter downstream temp* sens* voltage
PR672Damper valve position setpoint Vdiag 44 and 48 only
*AC: air conditioning system
*diff: differential*sens: sensor
*temp: temperature*press: pressure

13B-188
MR-372-J84-13B050$663.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Parameter summary table13B
*St.: storedTool Parameter
Diagnostic tool title
PR739Fuel flow solenoid valve current
PR794Stored regeneration failure no. 1
Vdiag 4D, 45 and 49 only PR795Stored regeneration failure no. 2
PR796Stored regeneration failure no. 3
PR797Stored regeneration failure no. 4
PR798Stored regeneration failure no. 5
PR799Stored regeneration failure no. 6
PR800Stored regeneration failure no. 7
PR801Stored regeneration failure no. 8
PR802Stored regeneration failure no. 9
PR803Stored regeneration failure no.10
PR810Catalytic converter 1 downstream temperature
Vdiag 4D, 45 and 49 only
PR812Catalytic converter 1 temperature sensor
voltage
PR836St* particle filter warning light no. 1
Vdiag 45 and 49 only PR837St* particle filter warning light no. 2
PR838St* particle filter warning light no. 3
PR839St* particle filter warning light no. 4
PR840St* particle filter warning light no. 5
PR841St* particle filter warning light no. 6
PR842St* particle filter warning light no. 7
PR843St* particle filter warning light no. 8
PR844St* particle filter warning light no. 9
PR845St* particle filter warning light no. 10
PR873Oil oxidation signal Vdiag 44, 45, 48 and 49 only
PR874Last service
PR875Oil dilution signal Vdiag 44, 45, 48 and 49 only
PR878Increased idle speed Kangoo II only
PR879Maximum authorised speed Kangoo II only

13B-233
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR383
WEIGHT OF SOOT IN PARTICLE FILTER
PARAMETER
DEFINITIONThis parameter indicates the weight of soot in the particle filter in grams.
NOTESSpecial notes:
Only apply the checks if the parameter is inconsistent.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
The weight of the soot contained in the filter must not be greater than 31 g.
If the particle filter warning light is illuminated or if the message Regenerate catalytic converter is displayed,
carry out a special type of driving (see Technical Note 6507, Particle filter fault finding).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR383/SID304_V45_PR383/SID304_V49_PR383/SID301_V4C_PR383

13B-239
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR513
LEVEL 1 WARNING LIGHT DISTANCE COUNTER
PARAMETER
DEFINITIONThis parameter indicates the number of miles (km) travelled since the Level 1 warning
light was last activated.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
PR513 = X km
Check the consistency of this parameter with the first appearance of possible faults associated with the Level 1
warning light.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR513/SID304_V45_PR513/SID301_V48_PR513/SID304_V49_PR513/SID304_V4D_PR513/SID301_V4C_PR513

13B-240
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR514
LEVEL 2 WARNING LIGHT DISTANCE COUNTER
PARAMETER
DEFINITIONThis parameter indicates the number of miles (km) travelled since the Level 2 warning
light was last activated.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
PR514 = X miles (km)
Check the consistency of this parameter with the first appearance of any faults related to the Level 2 warning
light.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR514/SID304_V45_PR514/SID301_V48_PR514/SID304_V49_PR514/SID304_V4D_PR514/SID301_V4C_PR514

13B-249
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR794
PR795
PR796
PR797
PR798
PR799
PR800
PR801
PR802
PR803REGENERATION FAILURE RECORD NO. 1
REGENERATION FAILURE RECORD NO. 2
REGENERATION FAILURE RECORD NO. 3
REGENERATION FAILURE RECORD NO. 4
REGENERATION FAILURE RECORD NO. 5
REGENERATION FAILURE RECORD NO. 6
REGENERATION FAILURE RECORD NO. 7
REGENERATION FAILURE RECORD NO. 8
REGENERATION FAILURE RECORD NO. 9
REGENERATION FAILURE RECORD NO. 10
SPECIFICATION OF
THE PARAMETERSThese parameters indicate the regeneration failure record in miles (km).
NOTESSpecial note:
Check the interpretation of these parameters only on ALP21 Particle filter warning
light illuminated.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
these parameters are used so that the history of the last ten regeneration failures when driving are known.
Each parameter from PR794 to PR803 records the distance when regeneration fails and the engine status is
recorded by ET706 Stored engine status no. 1 to ET715 Stored engine status no. 10 (for example: PR797
Stored regeneration failure no. 4 is associated with ET709 Stored engine status no. 4).
The value is saved in the next parameter (PR+1) each time a new save is performed.
The distance of the last regeneration failures when driving are recorded in the other available parameters
(distance information in PR794 is recopied in PR795 and distance information in PR795 is recopied in PR796 and
so on).
When all ten parameters have a value other than zero, and a failed regeneration occurs when driving, the
distance information for PR794 Regeneration failure record No.1 is erased and replaced by the new value.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V4D_PR794/SID304_V4D_PR795/SID304_V4D_PR796/SID304_V4D_PR797/SID304_V4D_PR798/SID304_V4D_PR799/
SID304_V4D_PR800/SID304_V4D_PR801/SID304_V4D_PR802/SID304_V4D_PR803/SID304_V49_PR794/SID304_V49_PR795/
SID304_V49_PR796/SID304_V49_PR797/SID304_V49_PR798/SID304_V49_PR799/SID304_V49_PR800/SID304_V49_PR801/
SID304_V49_PR802/SID304_V49_PR803/SID301_V4C_PR794/SID301_V4C_PR795/SID301_V4C_PR796/SID301_V4C_PR797/
SID301_V4C_PR798/SID301_V4C_PR799/SID301_V4C_PR800/SID301_V4C_PR801/SID301_V4C_PR802/SID301_V4C_PR803