rz019 RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Siemens Injection Workshop Manual

13B-26
MR-372-J84-13B050$273.mif
V17
13B
DIESEL INJECTION
Fault finding – Replacement of components
COMPUTER REPROGRAMMING OPERATIONS
The system can be reprogrammed via the diagnostic socket using the RENAULT CLIP diagnostic tool (see
Technical Note 3585A, Computer programming and reprogramming procedure).
Note:
Before reprogramming the injection computer, move the main Cruise control - Speed limiter switch to the rest
position. The information about the cruise control or the speed limiter displayed on the instrument panel disappears.
Otherwise, if the main switch remains in the cruise control or speed limiter position during and after reprogramming,
the Cruise control/Speed limiter function will not be operational. The procedure for resetting the function is as
follows:
– Vehicle ignition on.
– Main switch in rest position (the computer then detects the rest position).
– Switch in Cruise control position to activate the Cruise control function.
– Switch in Speed limiter position to activate the Speed limiter function.
While the computer is being reprogrammed the fan assemblies are triggered automatically.
Before reprogramming the computer:
– Save the computer data to the diagnostic tool (engine adaptives) by performing command SC003 Save
computer data.
After any computer reprogramming operation:
– Switch the ignition off and then on again,
–Use the diagnostic tool to carry out the following procedures:
– run command RZ019 Programming reinitialisation.
– run command SC001 Write saved data to restore the engine adaptives,
– run command SC013 Enter VIN,
– start the engine (warning: the start-up phase may last up to 30 seconds),
– after injection computer reprogramming, stored faults may appear in other computers. Clear the fault memory of
these computers,
– carry out a road test followed by another check with the diagnostic tool.
DO NOT CARRY OUT ANY INJECTOR CODE WRITING ON THE SIEMENS SID304 AND 301 INJECTION
SYSTEMS.IMPORTANT
Switch on the diagnostic tool (mains or cigarette lighter supply).
Connect a battery charger.
Switch off all the electrical consumers (lights, interior lighting, air conditioning, radio CD, etc.).
Wait for the engine to cool (engine coolant temperature < 60 °C and air temperature < 50 °C).
MR-372-J84-13B050$273.mif
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4CProgram No.: B1 and B2

13B-27
MR-372-J84-13B050$273.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Replacement of components13B
If no communication is possible with the injection computer during reprogramming or programming:
●Clear the programming using command RZ019 Reinitialise programming.
●Clear any faults using command RZ001 Fault memory.
●Enter the V.I.N. using command SC013 Enter VIN code.
●Perform a powerlatch.
●Perform a detection of the cruise control - speed limiter and the air conditioning:
– Vehicle ignition on.
– Main switch in rest position (the computer then detects the rest position).
– Switch in Cruise control position to activate the Cruise control function.
– Switch in Speed limiter position to activate the Speed limiter function.
– Air conditioning in the ON position.
●For Kangoo II, program the values for fast idle speed (if equipped) and vehicle speed restriction (if equipped)
using commands SC041 Modification of commercial vehicle idle speed and SC040 Speed limiter.
●For Vdiag 45, 49 and 4D, carry out a particle filter regeneration using command SC017 Particle filter
regeneration (see Interpretation of commands).
●For Clio III, Modus, Megane II and Scenic II vehicles:
– If the configuration reading LC106 O.C.S. is" WITH" (check in the instrument panel computer), perform
an engine oil change and initialise the value of the oil service interval using the instrument panel.
●For Kangoo II:
– Change the engine oil and initialise the value of the oil change interval using the instrument panel.
IMPORTANT
The injection computer retains the immobiliser code for life.
The system has no security code.
It is forbidden to perform tests with computers borrowed from the Parts Department or from another vehicle
which must then be returned.
These computers are hard-coded.
If the injection computer is faulty, contact the Techline (and refer to the fault finding log).

13B-28
MR-372-J84-13B050$273.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2DIESEL INJECTION
Fault finding – Replacement of components13B
COMPUTER REPLACEMENT AND PROGRAMMING OPERATIONS
The system can be programmed via the diagnostic socket using the RENAULT CLIP diagnostic tool (see
Technical Note 3585A, Computer programming and reprogramming procedure).
While the computer is being programmed the fan assemblies are triggered automatically.
Before any replacement and programming of the computer:
– When possible, back up the old computer data (engine adaptives) in the diagnostic tool, by performing
command SC003 "Computer data backup".
After the computer has been programmed:
– Switch the ignition off and then on again.
– Use the diagnostic tool to carry out the following procedures:
– Run command RZ019 Reinitialise programming.
– Run command SC001 Write saved data to restore the engine adaptives,
– Start the engine. Important: the starting phase can last up to 30 seconds.
– Stop the engine (to initialise the computer) and wait 30 seconds.
– Switch on the ignition again and use the diagnostic tool to carry out the following steps:
– Run command SC013 Enter VIN code.
– After the injection has been programmed, stored faults may appear on other computers.
– Clear the fault memory of these computers.
– Carry out a road test followed by a complete check with the diagnostic tool.
After the computer has been programmed:
– Switch the ignition off and then on again.
– Use the diagnostic tool to carry out the following procedures:
– Use command RZ019 Reinitialise programming.
– Use command SC001 Write saved data to restore the engine adaptives.
– Select the UCH field,
– In the repair mode, perform command SC017 Programming injection immobiliser code and follow the
indications provided by the diagnostic tool (command SC017 Programming injection immobiliser code is
accessible in the menu "Secure programming").
– Switch the ignition off and then on again.
– Select the INJECTION field and check ET006 Code programmed.
If ET006 is "YES":
– Start the engine. Important: the starting phase can last up to 30 seconds.
– Stop the engine (to initialise the computer) and wait 30 seconds.
– Switch on the ignition again and use the diagnostic tool to carry out the following steps:
– Perform command SC013 Enter VIN code.
– After the injection has been programmed, stored faults may appear on other computers.
Clear the fault memory of these computers.
If ET006 is: "NO":
– Rerun command SC017 Programming injection immobiliser code and follow the instructions provided by the
diagnostic tool.
– Repeat the method described above.IMPORTANT
– Switch on the diagnostic tool (mains or cigarette lighter supply).
– Connect a battery charger.
– Switch off all the electrical consumers (lights, interior lighting, air conditioning, radio CD, etc.).
– Wait for the engine to cool (engine coolant temperature < 60 °C and air temperature < 50 °C).

13B-235
MR-372-J84-13B050$780.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR400
NEW EGR VALVE OFFSET
PARAMETER
DEFINITIONThis parameter indicates the new EGR valve offset.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
Approximately 850 mV
In the event of a fault, run commands RZ019 and RZ002 Reinitialise programming and EGR Adaptive.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR400/SID304_V45_PR400/SID301_V48_PR400/SID304_V49_PR400/SID304_V4D_PR400/SID301_V4C_PR400

13B-258
MR-372-J84-13B050$819.mif
V17
13B
DIESEL INJECTION
Fault finding – Interpretation of commands
SPECIAL COMMAND
SC001: Enter saved data.
SC003: Save computer data.
SC013: Enter VIN.
SC017: Particle filter regeneration (Only for vehicles equipped with a particle filter).
SC040: Speed limiter (Kangoo II only).
SC041: Modification of the commercial vehicle idle speed (Kangoo II only).
CLEARING
RZ001: Fault memory.
Enables the faults to be cleared from the computer memory.
RZ002: EGR adaptives.
Use this command at the time of replacement or when cleaning the EGR valve.
RZ004: Pressure regulation adaptives.
This mode initialises the variables related to the regulation function.
RZ005: Programming (except Kangoo II).
This command enables you to reinitialise all the computer data (engine adaptives, EGR, rail, etc.).
RZ019: Reinitialise programming.
This mode initialises all of the programming contained in EEPROM.
RZ030: Particle filter adaptives (Vdiag 45, 49 and 4D only).
This mode initialises the variables related to the particle filter function.
ACTUATION
AC003: Fuel pressure solenoid valve.
AC005 to AC008: Injectors for cylinders 1 to 4.
Running this lets you listen to the operation of the injector on the cylinder in question.
AC012: Damper valve (except Vdiag 4C).
Activating this lets you listen to the operation of the damper valve.
AC029: High-pressure circuit seal check.
Running this lets you check the high pressure circuit sealing after an operation has been carried out.
Run this command with the engine running and the engine coolant temperature above 60°C.
MR-372-J84-13B050$819.mif
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4CProgram No.: B1 and B2

13B-267
MR-372-J84-13B050$819.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of commands
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
RZ019
REINITIALISE PROGRAMMING
NOTESThis command is used to reset the computer parameters according to the type of
operation or component repaired or replaced from the following list:
– the EGR valve,
– the damper valve,
– particle filter.
Ignition on and engine stopped.
To run this command, select command RZ019 Reinitialise programming on the CLIP diagnostic tool.
Procedure to be followed:
– on the main screen, select the component to reinitialise after an operation (removal/refitting or replacement of
component),
–select YES then OK to begin reinitialisation,
–select Finish on the Configuration completed screen to return to the main screen,
– end of operation.
SID301_V44_RZ019 / SID304_V45_RZ019 / SID301_V48_RZ019 / SID304_V49_RZ019 / SID304_V4D_RZ019 / SID301_V4C_RZ019

13B-303
MR-372-J84-13B050$936.mif
V17
DIESEL INJECTION
Fault finding – Tests13B
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
TEST 2 Internal fuel transfer pump (ITP) check
NOTESConditions prior to test:
Test 1 Low-pressure supply system check has been carried out previously and
results are satisfactory.
Cause:
Fuel is present in the transparent supply pipe leading to the pump.
However, fuel does not move during starting.
– Remove the connector of the fuel flow solenoid valve (orange)
– Disconnect the fuel return pipe from the pump and seal it with a plug. Connect a pipe to the pump to measure
the flow of diesel.
– To authorise a 15 second starter action and carry out this test it is essential to carry out the following
procedure:
– Connect a battery charger.
– Run command SC003 Save computer data.
– Run command RZ019 Programming reinitialisation.
– Perform a starter action for at least 15 seconds (starting speed 250 rpm).
– Measure the flow rate of the fuel being collected in a graduated measuring cylinder (500 ml minimum).
The minimum flow rate must be 25 ml every 15 sec.
– Run command SC001 Enter computer data.
Is the flow measured less than 25 ml?
NO
Low pressure system correct.
YESReplace the pump.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
SID301_V44_TEST2 / SID304_V45_TEST2 / SID301_V48_TEST2 / SID304_V49_TEST2 / SID304_V4D_TEST2 / SID301_V4C_TEST2

13B-314
MR-372-J84-13B050$936.mif
V17
DIESEL INJECTION
Fault finding – Tests13B
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
TEST 6
CONTINUED 1
Disconnect the return system connections at the injectors and
close off the return pipes so they are leak-tight (pipe and can
kit for engines1711 and 1771).
– To authorise a 15 second starter action and carry out this
test it is essential to carry out the following procedure:
– Run command SC003 Save computer data.
– Run command RZ019 Programming reinitialisation.
– Perform a starter action for at least 15 seconds (starting
speed 250 rpm).
– Run command SC001 Enter computer data.
Is the return volume at the injectors greater than 20 ml per
injector for the starting phase?
Note:
Do not repeat this procedure more than 3times and wait
30 seconds between each 15 second starter activation.
Then wait 30 mins before activating the starter for
315second cycles.
Follow this instruction to avoid damage to the starter.
NO
YESReplace the corresponding
injectors.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
B
A