Temperature RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Owner's Manual

13B-76
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF114
CONTINUED
Check the resistance of the EGR valve, component code 169:
– with the engine stopped, the EGR valve will be closed (unless there is a fault),
– wait for the ambient temperature around the valve to stabilise (approximately 20°C),
– measure the resistance between connections 3FB2 and 3GB. The resistance must be between
7.5Ω – measure the resistance between connections 3GC and 3JM. The resistance must be between
2.4 kΩ – measure the resistance between connections 3JM and 3EL. The resistance must be between
800Ω If the value is not correct, replace the EGR valve, component code 169 (see MR 364 (Mégane II), MR 370 (Scénic
II), Mechanical, 14A, Emission control, Exhaust gas recirculation solenoid valve: Removal - Refitting). If the
EGR valve was replaced, use command RZ002 EGR adaptives to reinitialise the EGR valve offsets.
Also, if a 3.DEF, 4.DEF, or 5.DEF fault is present:
Remove the EGR valve. Check that there are no foreign bodies (scale, etc.) that could jam the valve.
Remove the foreign matter and clean the EGR valve (see MR Technical Note 3916, Cleaning the EGR solenoid
valve).
Use command RZ002 EGR adaptives to reinitialise the EGR valve offsets.
Clear the faults from the computer memory. Carry out a road test followed by another check with the diagnostic
tool.
If the fault is still present, contact the Techline.

13B-78
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF121
STOREDACCELEROMETER CIRCUIT
NOTESPriorities when dealing with a number of faults :
DF001 Coolant temperature sensor circuit,
DF002 Air temperature sensor circuit,
DF098 Fuel temperature sensor circuit,
DF003 Atmospheric pressure sensor circuit.
A fault on these sensors could lead to incorrect fault finding on the accelerometer.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Check the conformity of the injectors fitted to the vehicle in relation to the type of vehicle and engine number
(low, high or very high pressure injector).
Check the condition and connection of the accelerometer connector.
Repair if necessary.
Check the connection and condition of the brown 48-track connector B of the computer and check the sensor
shielding on track K1.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Sensor connector track 1 Track F1 computer connector B
Sensor connector track 2 Track G1 computer connector B
Repair if necessary.
Check that the C2I is correctly entered on the computer.
Check that the accelerometer is secured on the engine.
Disconnect and reconnect the accelerometer sensor to accomplish fast programming.
Carry out a road test followed by another check with the diagnostic tool.
If the fault is still present, replace the accelerometer.

13B-83V4 MR-372-J84-13B000$070.mif
13B
DDCR INJECTION
Vdiag No.: 44, 48
MAIN STATUSES AND PARAMETERS OF THE COMPUTER:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Battery
voltagePR074: Battery
voltage12 V < PR074 < 13.5 VIf there is a fault, apply the
fault finding procedure for the
"Charge circuit".
Engine speedPR055: Engine
speedIndicates the engine's speed of
rotation in rpm.In the event of a fault, apply
the fault finding procedure for
DF005 "Engine speed sensor
circuit".
Accelerator
pedal positionPR030: Accelerator
pedal position.
0%Indicates the position of the
accelerator pedal as a %.
PR030 = 0 %In the event of a fault, apply
the fault finding procedure for
Pedal sensor circuit gang 1
and gang 2
(DF008 and DF009)
and DF113 Sensor supply
voltage.
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90 °CIndicates the coolant
temperature in °C.
Default value: 80°CIn the event of a fault, consult
the interpretation of
parameter PR064 Coolant
temperature.
External air
temperaturePR061: External air
temperatureGives the external air
temperature in °C. This
parameter is controlled by the
UCH and transmitted to the
injection via the multiplex
network.
Default value: 20°C.In the event of a fault, apply
the fault finding procedure for
this fault described in the
UCH document.
DIESEL INJECTION
Fault finding – Conformity check

13B-84V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
MAIN COMPUTER STATUSES AND PARAMETERS: (continued 1)
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Inlet air
temperature
(invalid for
K9K 728)PR059: Inlet air
temperature.
Cold = PR061
Warm: 30°CIndicates the inlet air
temperature in °C. This
information is provided by the
air temperature/pressure
sensor.
Default value: 30°CIn the event of a fault, refer to
the interpretation of
parameter PR059 Inlet air
temperature.
Fuel
temperaturePR063: Fuel
temperature.
Cold = PR064
Warm: 50°CGives the fuel temperature
in °C. This value is supplied by
"the fuel temperature sensor".
Default value: 30°CIn the event of a fault, apply
the fault finding procedure for
fault DF098 "Fuel temperature
sensor circuit".
Air circuit
pressure.PR035: Atmospheric
pressure.Indicates the atmospheric
pressure in mbar. The sensor is
built into the computer.If not consistent, check that
PR035 = PR032 = local
atmospheric pressure,
with the engine stopped
and the ignition on. PR032: Inlet
pressure.Indicates the pressure in the
inlet circuit in mbar.
Rail pressurePR038: Rail
pressure.
cold and hot:
-90 bar < PR038
<90barIndicates the pressure, in bar, of
the diesel fuel in the injector
rail. This pressure is supplied
by the sensor on the rail.
Default value: 2000 barIn the event of a fault apply
the fault finding procedure for
fault DF007 "Rail pressure
sensor circuit".

13B-89V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
COLD LOOP SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Air conditioning
presentET079: Air
conditioning
present.
YESIndicates whether the vehicle is
fitted with air conditioning or not.
- YES: Air conditioning is
detected by the injection
computer.
- NO: Air conditioning is not
detected by the injection
computer.If inconsistent with the vehicle
equipment, perform a multiplex
network test and apply the
associated procedure.
Compressor
activation requestET088: Compressor
activation request.
INACTIVEThe injection requests the
Protection and Switching Unit
(via the multiplex network) to
start the compressor.
- ACTIVE: The multiplex network
must not be faulty on the
Automatic transmission,
Protection and Switching Unit, or
UCH systems. The UCH should
request the injection to be
engaged. The coolant pressure
sensor must not be defective.
Satisfactory engine operating
conditions (Coolant temperature,
engine load, etc.).
- INACTIVE: One of the above
conditions is not fulfilled.NONE

13B-90V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
COLD LOOP SUB-FUNCTION (continued 1):
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Air conditioning
authorisedET004: Air
conditioning
authorised.
NONon operational information,
designed solely for fault finding
purposes.
- YES: Satisfactory engine
operating conditions (coolant
temperature, engine load etc.).
The vehicle is not in a specific
movement phase (hill start, start
from stop etc.).
- NO: One of the above
conditions is not fulfilled.NONE
Refrigerant
pressure.PR037: Refrigerant
pressure.Gives the value in BAR for the
refrigerant fluid in the system.
2 bar < PR037 < 27 bar
Default value: 0 barIf there is a fault apply the fault
finding procedure for DF049
"Refrigerant sensor circuit". If
the fault is still present, replace
the refrigerant sensor.
Engine speedPR055: Engine
speed.Indicates the engine's speed of
rotation in rpm.In the event of a fault, apply the
fault finding procedure for
DF005 "Engine speed sensor
circuit".
Fast idle speed
requestET023: Fast idle
speed request.
ABSENTThe UCH requests fast idle speed
from the injection.
- ABSENT: The UCH did not make
a request.
- PRESENT: The UCH made
a request.If ET023 is inconsistent, carry
out a multiplex network test
using the diagnostic tool. If the
test is correct, consult the fault
finding procedure for the UCH.
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90°CIndicates the coolant
temperature in °C.
Default value: 80°CIn the event of a fault, consult
the interpretation of parameter
PR064 Coolant temperature.

13B-91V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
COLD LOOP SUB-FUNCTION (continued 2):
* When the air conditioning is requested with the engine idling and the vehicle speed = 0 mph (0 km/h),
ET022 will always be ACTIVE and ET021 INACTIVE (unless refrigerant pressure > 15 bar, vehicle speed
= 0 mph, and high coolant temperature). The fan assemblies are disabled under certain coolant temperature
conditions when driving.
When the UPC stops receiving multiplex transmissions from the injection, the fan assemblies are
constantly activated.
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Vehicle speedPR089: Vehicle
speed.Indicates the vehicle speed in mph.
This parameter is transmitted by the
ABS computer or by the vehicle
speed ECU. This signal is
transmitted to the injection system
on the multiplex network.Test the multiplex network.
Refer to fault finding for the
ABS or the vehicle speed
ECU.
Power consumed
by the air
conditioning
compressorPR125: Power
consumed by the air
conditioning
compressor.
0 WIndicates the power consumed by
the compressor.NONE
Speed request
for fan
assembly*ET022: Low speed
fan assembly
request.
INACTIVE.The injection requests the UPC to
start the fans.
- INACTIVE: Because engine speed
= 0 rpm.
- ACTIVE: Engine speed = idle
speed, correct refrigerant pressure
and vehicle speed = 0 mph (km/h),
or high coolant temperature.NONE
Speed request
for fan
assembly*ET021: High speed
fan assembly
request.
INACTIVE.The injection requests the UPC to
start the fans.
- INACTIVE: Because engine speed
= 0 rpm.
- ACTIVE: Engine speed = idle
speed. Refrigerant pressure
> 15 bar, vehicle speed = 0 mph,
or high coolant temperature.NONE

13B-92V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
HEATING SUB-FUNCTION:
*RCH = Passenger Compartment Heating Resistor
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90 °CIndicates the coolant temperature
in °C.
Default value: 80°CIn the event of a fault,
consult the interpretation
of parameter PR064
Coolant temperature.
Set number of
RCHET111: Set number of
RCH.
YES - NOThe RCHs* are actuated by the UCH.
They are high current consumers.
Consequently, their use is
conditional on the available power
all the time (alternator power).
The injection checks the balance of
available mechanical power
according to the engine operating
conditions (torque, power, etc.) to
authorise, limit, or stop their use.
(This information is sent via the
CAN network to the UCH).
Note: When the RCHs* are actuated,
the injection system must respond
to a fast idle speed request from the
UCH.NONE
RCH cut-offET112: RCH cut-off
YES - NO

13B-93V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
FUEL CIRCUIT SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Fuel
temperaturePR063: Fuel
temperature.
Cold = PR064
Warm: 50°CGives the fuel temperature in °C.
Default value: 30°CIn the event of a fault,
apply the fault finding
procedure for fault
DF098 "Fuel temperature
sensor circuit".
Fuel flowPR017: Fuel flow.
0.0 mg/stShows the fuel injected in mg/st for
each injector.
PR017 = 0 mg/stNONE
Rail pressurePR038: Rail pressure.
Cold and warm:
-90 bar < PR038
<90barIndicates the pressure, in bar, of the
diesel fuel in the injector rail. This
pressure is supplied by the sensor
on the rail.
Default value: 2000 barIn the event of a fault
apply the fault finding
procedure for fault
DF007 "Rail pressure
sensor circuit".
Rail pressure
set pointPR008: Rail pressure
setpoint.
375 bar (Engine
starting pressure
setpoint).
Cold: 500 bar.
Warm: 300 barGives a theoretical pressure value
for optimum engine operation.
300 bar < PR008 < 500 barNONE

13B-95V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
PRE-HEATING/IGNITION SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90 °CIndicates the coolant
temperature in °C.
Default value: 80°CIn the event of a fault, consult
the interpretation of
parameter PR064 Coolant
temperature.
External air
temperaturePR061: External air
temperatureGives the external air
temperature in °C. This
parameter is controlled by
the UCH and transmitted to
the injection via the multiplex
network.
Default value: 20°CIn the event of a fault, apply
the fault finding procedure for
this fault described in
the UCH document.
Inlet air
temperature
(invalid for
K9K 728)PR059: Inlet air
temperature.
Cold = PR061
Warm: 30°CIndicates the inlet air
temperature in °C. This signal is
provided by the air temperature/
pressure sensor.
Default value: 30°C.In the event of a fault, refer to
the interpretation of
parameter PR059 Inlet air
temperature.
Battery
voltagePR074: Battery
voltage12 V < PR074 < 13.5 VIf there is a fault, apply the
fault finding procedure for
the "Charge circuit".