engine coolant RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Owner's Manual

13B-111V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
COLD LOOP SUB-FUNCTION (continued 2):
*When the air conditioning is requested with the engine idling and the vehicle speed = 0 mph (0 km/h),
ET022 will always be ACTIVE and ET021 INACTIVE (unless refrigerant pressure > 15 bar, vehicle speed
= 0 mph (0 km/h) and high coolant temperature). The fan assemblies are disabled under certain coolant
temperature conditions when driving.
When the UPC stops receiving multiplex transmissions from the injection, the fan assemblies are
constantly activated.
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or
Status Check or
actionDisplay and notes Fault finding
Power consumed
by the air
conditioning
compressorPR125: Power
consumed by the
air conditioning
compressor.
0 WATTIndicates the power consumed by the
compressor.NONE
Fan assembly
speed request*ET022: Low speed
fan assembly
request.
INACTIVE.The injection requests the UPC to start the fans.
- INACTIVE: The request was not made by the
injection because ET088 = INACTIVE and ET004
=NO.
- ACTIVE: The request was made by the injection.
ET088 = ACTIVE and ET004 = YES.
(Correct refrigerant pressure and vehicle speed
= 0 mph (0 km/h) or high coolant temperature).
NONE
ET021: High
speed fan
assembly request.
INACTIVE.The injection requests the UPC to start the fans.
- INACTIVE: The request was not made by the
injection because ET088 = INACTIVE and ET004
=NO.
- ACTIVE: The request was made by the injection.
ET088 = ACTIVE and ET004 = YES.
(Refrigerant pressure > 15 bar and vehicle speed
= 0 mph or high engine coolant temperature).

13B-112V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
HEATING SUB-FUNCTION:
*RCH = Passenger Compartment Heating Resistor
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or
Status Check or
actionDisplay and notes Fault finding
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90 °CIndicates the coolant temperature in °C.
Default value: 80°C
RCH* number setET111: RCH*
number set.
YES - NOThe RCHs* are actuated by the UCH. They are high
current consumers. Consequently, their use is
conditional on the available power all the time
(alternator power). The injection checks the
balance of available mechanical power according
to the engine operating conditions (torque, power,
etc.) to authorise, limit, or stop their use.
(This information is sent via the CAN to the UCH).
Note: When the RCHs* are actuated, the injection
system must respond to a fast idle speed request
from the UCH.NONE
RCH cut-offET112: RCH*
cut-off
YES - NO

13B-115V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
PRE-HEATING/IGNITION SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90°CIndicates the coolant temperature
in °C.
Default value: 80°CIn the event of a fault,
consult the
interpretation of
parameter PR064
Coolant temperature.
External air
temperaturePR061: External air
temperature.Gives the external air temperature
in °C. This parameter is controlled
by the UCH and transmitted to the
injection via the multiplex network.
Default value: 20°CIn the event of a fault,
apply the fault finding
procedure for this fault
described in the UCH
document.
Inlet air
temperature
(invalid for
K9K 728)PR059: Inlet air
temperature.
Cold = PR061
Warm: 30°CIndicates the inlet air temperature
in °C. This signal is provided by the
air temperature/pressure sensor.
Default value: 30°C.In the event of a fault,
refer to the
interpretation of
parameter PR059 Inlet
air temperature.
Battery voltage PR074: Battery voltage.12 V < PR074 < 14 VIf there is a fault, apply
the fault finding
procedure for the
"Charge circuit".

13B-117V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
ENGINE COOLING SUB FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90°CIndicates the coolant
temperature in °C.
Default value: 80°CIn the event of a fault,
consult the interpretation
of parameter PR064
Coolant temperature.

13B-120V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
SUB-FUNCTION: ANTIPOLLUTION/OBD (cont.):
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
EGR valve
position sensor
voltagePR077: EGR valve position
sensor voltage.Indicates the EGR valve voltage
according to its position.
- INACTIVE: The valve is not
controlled by the computer.
- ACTIVE: The valve is controlled
by the computer.
0.5 V < PR077 < 4.8 VNONE
Accelerator pedal
positionPR030: Accelerator pedal
position.
0%.Shows the pedal position
between NO LOAD and FULL
LOAD as a percentage.
0< PR030 < 100%In the event of a fault,
apply the fault finding
procedures for Pedal
sensor circuit gang 1 and
gang 2 (DF008 and DF009)
and DF113 Sensor supply
voltage.
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90 °CIndicates the coolant
temperature in °C.
Default value: 80°CIn the event of a fault,
consult the interpretation
of parameter PR064
Coolant temperature.

13B-143V4 MR-372-J84-13B000$100.mif
13B
DDCR INJECTION
Vdiag No.: 44, 48
* Heat.: HeatingTool parameter DIAGNOSTIC TOOL DESCRIPTION
PR005 EGR valve opening setpoint
PR008 Rail pressure set point
PR009 Turbocharging pressure setpoint
PR010 Idle speed regulation setpoint
PR017 Fuel flow
PR073 Air flowmeter supply voltage
PR028 Pedal position (gang 1)
PR029 Pedal position (gang 2)
PR030 Accelerator pedal position
PR032 Inlet pressure
PR035 Atmospheric pressure
PR037 Refrigerant pressure
PR038 Rail pressure
PR051 EGR valve position feedbac
PR055 Engine speed
PR059 Inlet air temperature (invalid in K9K 728)
PR061 External air temperature
PR063 Fuel temperature
PR064 Coolant temperature
PR074 Battery voltage
PR077 EGR valve position sensor voltage
PR080 Rail pressure sensor voltage
PR081 Inlet temperature sensor voltage
PR088 Pedal potentiometer gang 2 voltage
PR089 Vehicle speed
PR125 Power absorbed by air conditioning compressor
PR127 Heat.* resistor maximum authorised power
PR130 Cruise control setpoint
PR132 Air flow
DIESEL INJECTION
Fault finding – Parameter summary table

13B-155V4 MR-372-J84-13B000$120.mif
DIESEL INJECTION
Fault finding – Tests13B
DDCR INJECTION
Vdiag No.: 44, 48
TEST 8 Injector return flow
NOTESSpecial note:
Certain faults make it impossible to carry out this test - deal with these first.
Does the engine start?
Command AC029 also checks the return volume of each injector to detect an internal injector leak.
Be careful with any objects (tool or other) on the engine housing during the four cycles of the operation
(possible vibrations).
Tooling required
–Mot. 1711 Injector flow measuring kit.
Or: Use four pipes with internal diameter 4mm and approximately 50 cm in length, and four graduated measuring
cylinders.
Procedure
– Ensure that the engine coolant temperature is above 60°C,
– switch off the ignition,
– disconnect the return pipes from the four injectors,
– cap the pump venturi tube to prevent the low-pressure circuit from depriming,
– connect the four transparent tubes in place of the return pipes,
– put the other ends of the four pipes into four graduated measuring cylinders.
– After finishing these preparations, start the engine and let it idle for 2 minutes.
Note: This idle time must be respected for the test results to be interpreted correctly.
–Run command AC029 High pressure circuit sealing check
.The engine will automatically carry out a cycle of four accelerations to increase the rail pressure and measure the
internal injector leaks under these conditions.
–Once the cycle is complete, run command AC029 again to obtain a correct reading of the return volume of
each injector.
– Switch off the engine at the end of the cycle.
NOA
YES
DDCR_V44_TEST08/DDCR_V48_TEST08

13B-167
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V4 MR-372-J84-13B000$140.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
InjectionDDCR
Vdiag No.: 44, 48
ALP2 The engine will not start
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Check that the fuel tank is correctly filled and that the fuel is correct: run TEST 13 Diesel fuel conformity check.
Check the levels of engine oil and coolant.
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Is the catalytic converter clogged or damaged?Replace the catalytic converter (see MR
364 (Mégane II) or MR 370 (Scénic II),
Mechanical, 19B, Exhaust, Catalytic
converter: Removal - Refitting).
Check the air inlet circuit by running TEST 2 Electrical circuit check.
Check the electrical conformity of the heater plugs (the resistance value of the heater plug must be less than 2 Ω).
Is the timing set correctly? Carry out the necessary repairs.
Visually check the condition of the engine wiring harness.
YES
NO
NO
YES
A
DDCR_V44_ALP02/DDCR_V48_ALP02

13B-170
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V4 MR-372-J84-13B000$140.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
InjectionDDCR
Vdiag No.: 44, 48
ALP3 The engine starts with difficulty, or starts then stalls
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Check that the fuel tank is correctly filled and that the fuel is correct by running TEST 13 Diesel fuel conformity
check.
Check the levels of engine oil and coolant.
Check the air inlet circuit: run test 5 Air inlet circuit check.
Is the catalytic converter clogged or damaged?Replace the catalytic converter (see MR 364
(Mégane II) or MR 370 (Scénic II),
Mechanical, 19B, Exhaust, Catalytic
converter: Removal - Refitting).
Check the electrical conformity of the heater plugs (the resistance value of the heater plug must be less than 2 Ω).
Is the timing set correctly? Carry out the necessary repairs.
Is the compression in order? Carry out the necessary repairs.
YES
NO
NO
YES
NO
YES
A
DDCR_V44_ALP03/DDCR_V48_ALP03

13B-179
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V4 MR-372-J84-13B000$140.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
InjectionDDCR
Vdiag No.: 44, 48
ALP9 Engine cut-out (stalling)
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Check that the fuel tank is correctly filled and that the fuel is correct by running TEST 13 Diesel fuel conformity
check.
Check the levels of engine oil and coolant.
Check that the engine has not sucked up its oil (engine racing).
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Is the catalytic converter clogged or
damaged?Replace the catalytic converter (see MR 364
(Mégane II) or MR 370 (Scénic II), Mechanical, 19B,
Exhaust, Catalytic converter: Removal - Refitting).
Visually check the condition of the engine wiring harness.
Check the air inlet circuit by running TEST 2 Electrical circuit check.
Check the low pressure circuit by running TEST 1 Low pressure circuit check.
YES
NO
A
DDCR_V44_ALP09/DDCR_V48_ALP09