engine RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Repair Manual

13B-76
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF114
CONTINUED
Check the resistance of the EGR valve, component code 169:
– with the engine stopped, the EGR valve will be closed (unless there is a fault),
– wait for the ambient temperature around the valve to stabilise (approximately 20°C),
– measure the resistance between connections 3FB2 and 3GB. The resistance must be between
7.5Ω – measure the resistance between connections 3GC and 3JM. The resistance must be between
2.4 kΩ – measure the resistance between connections 3JM and 3EL. The resistance must be between
800Ω If the value is not correct, replace the EGR valve, component code 169 (see MR 364 (Mégane II), MR 370 (Scénic
II), Mechanical, 14A, Emission control, Exhaust gas recirculation solenoid valve: Removal - Refitting). If the
EGR valve was replaced, use command RZ002 EGR adaptives to reinitialise the EGR valve offsets.
Also, if a 3.DEF, 4.DEF, or 5.DEF fault is present:
Remove the EGR valve. Check that there are no foreign bodies (scale, etc.) that could jam the valve.
Remove the foreign matter and clean the EGR valve (see MR Technical Note 3916, Cleaning the EGR solenoid
valve).
Use command RZ002 EGR adaptives to reinitialise the EGR valve offsets.
Clear the faults from the computer memory. Carry out a road test followed by another check with the diagnostic
tool.
If the fault is still present, contact the Techline.

13B-78
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF121
STOREDACCELEROMETER CIRCUIT
NOTESPriorities when dealing with a number of faults :
DF001 Coolant temperature sensor circuit,
DF002 Air temperature sensor circuit,
DF098 Fuel temperature sensor circuit,
DF003 Atmospheric pressure sensor circuit.
A fault on these sensors could lead to incorrect fault finding on the accelerometer.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Check the conformity of the injectors fitted to the vehicle in relation to the type of vehicle and engine number
(low, high or very high pressure injector).
Check the condition and connection of the accelerometer connector.
Repair if necessary.
Check the connection and condition of the brown 48-track connector B of the computer and check the sensor
shielding on track K1.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connections:
Sensor connector track 1 Track F1 computer connector B
Sensor connector track 2 Track G1 computer connector B
Repair if necessary.
Check that the C2I is correctly entered on the computer.
Check that the accelerometer is secured on the engine.
Disconnect and reconnect the accelerometer sensor to accomplish fast programming.
Carry out a road test followed by another check with the diagnostic tool.
If the fault is still present, replace the accelerometer.

13B-79
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF122
PRESENTPEDAL POTENTIOMETER GANG 2 SUPPLY VOLTAGECO.1: Open circuit or short circuit to +12 volts
CC.0: Short circuit to earth
NOTESSpecial notes:
If DF122, the idling speed is stuck at 1000 rpm, the engine performance is reduced to
75%, and the level 1 warning light illuminates along with the message Faulty
injection.
CC.0
NOTESNone.
Check the connection and condition of the 6-track connector of the pedal potentiometer.
Repair if necessary.
Check the connection and condition of the black 32-track connector A of the computer.
Repair if necessary.
Measure the resistance between tracks 2 and 6 of the pedal potentiometer.
Replace the pedal potentiometer if the resistance is not 2.85 kΩ +
2.05 Ω.
Disconnect computer connector A and the pedal potentiometer connector.
Check the insulation against earth of the connection on track F2 on computer connector A.
Repair if necessary.
DDCR_V44_DF122P/DDCR_V48_DF122P

13B-81
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF130
STOREDFLOW CAPACITY FUNCTION
NOTESSpecial notes:
If DF130, the engine may stop with the level 1 and 2 warning lights illuminated along
with the message Faulty injection.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine running.
Check the connection and condition of the of the fuel flow actuator connector (IMV), and repair it if necessary.
Measure the resistance between tracks 1 and 2 of the flow actuator.
Replace the flow actuator if the resistance is not 5.3 Ω ± 0.5 Ω at 20°C.
Check the connection and condition of the computer 48-track brown connector B.
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the following connection:
Computer connector B track M4 track 1 fuel flow actuator
Repair if necessary.
Check that there is fuel present in the tank and that it is correct. Run Test 13 Diesel fuel conformity check.
Run Test 1 Low pressure circuit check.
Run Test 6 High pressure system check.
Repair if necessary.
DDCR_V44_DF130M/DDCR_V48_DF130M

13B-82
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF1070
PRESENT
OR
STOREDCOLD LOOP
1.DEF: Jammed component
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present with the engine running and with a climate control request.
Priorities when dealing with a number of faults:
– DF049 Refrigerant sensor circuit if it is present or stored.
When the fault is present or stored, the heating and air conditioning system is inhibited. There is no longer any air
conditioning.
Check fuse F22 (10 A) of the UPC, component code 1337.
Check the connector of the air conditioning compressor, component code 171.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the wiring of the air conditioning compressor.
If the wiring is faulty and there is a repair procedure (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Manually check if the compressor is jammed (turn the clutch plate manually to check that there is no point of
resistance). In the event of jamming, replace the air conditioning compressor (see MR 364 (Mégane II), MR 370
(Scénic II), Mechanical, 62A, Air conditioning, Compressor: Removal - Refitting).
Top up the refrigerant, check for any leaks, and repair if necessary (see MR 364 (Mégane II), MR 370 (Scénic II),
Mechanical, 62A, Air conditioning, Refrigerant circuit: Draining - Filling).
DDCR__V44_DF1070 / DDCR_V48_DF1070

13B-83V4 MR-372-J84-13B000$070.mif
13B
DDCR INJECTION
Vdiag No.: 44, 48
MAIN STATUSES AND PARAMETERS OF THE COMPUTER:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Battery
voltagePR074: Battery
voltage12 V < PR074 < 13.5 VIf there is a fault, apply the
fault finding procedure for the
"Charge circuit".
Engine speedPR055: Engine
speedIndicates the engine's speed of
rotation in rpm.In the event of a fault, apply
the fault finding procedure for
DF005 "Engine speed sensor
circuit".
Accelerator
pedal positionPR030: Accelerator
pedal position.
0%Indicates the position of the
accelerator pedal as a %.
PR030 = 0 %In the event of a fault, apply
the fault finding procedure for
Pedal sensor circuit gang 1
and gang 2
(DF008 and DF009)
and DF113 Sensor supply
voltage.
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90 °CIndicates the coolant
temperature in °C.
Default value: 80°CIn the event of a fault, consult
the interpretation of
parameter PR064 Coolant
temperature.
External air
temperaturePR061: External air
temperatureGives the external air
temperature in °C. This
parameter is controlled by the
UCH and transmitted to the
injection via the multiplex
network.
Default value: 20°C.In the event of a fault, apply
the fault finding procedure for
this fault described in the
UCH document.
DIESEL INJECTION
Fault finding – Conformity check

13B-84V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
MAIN COMPUTER STATUSES AND PARAMETERS: (continued 1)
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Inlet air
temperature
(invalid for
K9K 728)PR059: Inlet air
temperature.
Cold = PR061
Warm: 30°CIndicates the inlet air
temperature in °C. This
information is provided by the
air temperature/pressure
sensor.
Default value: 30°CIn the event of a fault, refer to
the interpretation of
parameter PR059 Inlet air
temperature.
Fuel
temperaturePR063: Fuel
temperature.
Cold = PR064
Warm: 50°CGives the fuel temperature
in °C. This value is supplied by
"the fuel temperature sensor".
Default value: 30°CIn the event of a fault, apply
the fault finding procedure for
fault DF098 "Fuel temperature
sensor circuit".
Air circuit
pressure.PR035: Atmospheric
pressure.Indicates the atmospheric
pressure in mbar. The sensor is
built into the computer.If not consistent, check that
PR035 = PR032 = local
atmospheric pressure,
with the engine stopped
and the ignition on. PR032: Inlet
pressure.Indicates the pressure in the
inlet circuit in mbar.
Rail pressurePR038: Rail
pressure.
cold and hot:
-90 bar < PR038
<90barIndicates the pressure, in bar, of
the diesel fuel in the injector
rail. This pressure is supplied
by the sensor on the rail.
Default value: 2000 barIn the event of a fault apply
the fault finding procedure for
fault DF007 "Rail pressure
sensor circuit".

13B-85V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
MAIN COMPUTER STATUSES AND PARAMETERS: (continued 2)
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
EngineET038: Engine.
UNDER + AFTER
IGNITION FEEDIndicates the current status of
the engine.
- UNDER + AFTER IGNITION
FEED
- UNDER STARTER
- RUNNING
- SUPPLY MAINTAINED: Supply
maintained during the power
latch phase.
- STALLED: When the engine
has stalled.
- PROTECTED: When a level 2
fault has appeared or when
the engine speed is locked at
a certain value.NONE
Engine
immobiliserET003: Engine
immobiliser.
INACTIVEIndicates the status of the
immobiliser system.
- INACTIVE: The injection
computer has recognised the
immobiliser code transmitted
by the UCH.
- ACTIVE: The injection
computer does not recognise
the immobiliser code
transmitted by the UCH.If ACTIVE, apply the
associated Help given in
the tool.
Code
programmedET006: Code
programmed
YESIndicates whether the
immobiliser code has been
programmed into the computer.
- YES: Code is programmed.
- NO: Code was not
programmed into the injection
computer.If NO, contact the Techline.

13B-86V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
MAIN COMPUTER STATUSES AND PARAMETERS: (continued 3)
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Vehicle speedPR089: Vehicle
speedIndicates the vehicle speed in
mph. This parameter is
transmitted by the ABS
computer or by the vehicle
speed ECU. This signal is
transmitted to the injection
system on the multiplex
network. Test the multiplex network.
Refer to fault finding for the
ABS or the vehicle speed
ECU.
New pump
chamber filling ET637: New pump
chamber fillingCOMPLETEDIf NOT DONE, see
Replacement of components.

13B-87V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
STARTING SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
+ After ignition
computer feedET001: + After ignition
computer feed.
PRESENTIndicates + after ignition feed to
the computer.
- Present
- AbsentIn the event of a fault, apply
the fault finding procedure for
DF047 "Computer feed
voltage" or DF015 "Main relay
control circuit".
StartingET076: Starting.
AUTHORISEDIndicates whether or not
starting has been authorised by
the injection.
AUTHORISED: The injection
authorises starting.
PROHIBITED: The injection
does not authorise starting.If PROHIBITED, carry out
a complete fault finding
procedure on the preheating
system.
EngineET038: Engine.
UNDER + AFTER
IGNITION FEEDIndicates the current status of
the engine.
- UNDER + AFTER IGNITION
FEED
- UNDER STARTER
- RUNNING
- SUPPLY MAINTAINED: Supply
maintained during the power
latch phase.
- STALLED: When the engine
has stalled.
- PROTECTED: When a fault has
appeared or when the engine
speed is locked at a certain
value.NONE
Battery
voltagePR074: Battery
voltage.12 V < PR074 < 13.5 VIf there is a fault, apply the
fault finding procedure for
the "Charge circuit".