wiring diagram RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Workshop Manual

13B-2V4 MR-372-J84-13B000$010.mif
13B
DDCR INJECTION
Vdiag No.: 44, 48
1. APPLICABILITY OF THE DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
Following the introduction of the Pump repriming function on K9K engines, a new Vdiag was issued to cover this
function.
When replacing a high pressure pump on vehicles fitted with a computer with Vdiag 44, it is essential to reprogram
the injection computer to activate the Pump repriming function.
After reprogramming, Vdiag 44 is replaced by Vdiag 48.
2. PREREQUISITES FOR FAULT FINDING:
Documentation type:
Fault finding procedures (this document):
– Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
– Visu-Schéma (CD-ROM), paper.
Type of diagnostic tools:
–CLIP
Special tooling required:
3. REMINDERS
Procedure
To run fault finding on the vehicle's computers, switch on the ignition in fault finding mode (forced + after ignition
feed).
Proceed as follows:
– Vehicle card in card reader.
– Press and hold the start button (longer than 5 seconds) with the start-up conditions not fulfilled.
– Then connect the diagnostic tool and perform the required operations.Vehicle(s): MEGANE II, SCENIC II
for engines K9K 722, 728, 729
Function concerned: DELPHI K9 DIESEL
DIRECT COMMON RAIL INJECTION (DDCR)Computer name: DDCR INJECTION
Program No.: BE
Vdiag No.: 44, 48
SPECIAL TOOLING REQUIRED
Multimeter.
Elé. 1590 112-track computer bornier.
Elé. 1681 Universal bornier.
Mot. 1711 Injector flow measuring kit.
DDCR_V44_PRELI/DDCR_V48_PRELI
DIESEL INJECTION
Fault finding – Introduction

13B-33
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF010
STOREDEGR POSITION SENSOR CIRCUITCO.0: Open circuit or short circuit to earth
CC.1: Short-circuit on +12 volts.
1.DEF: Above maximum threshold.
2.DEF: Below minimum threshold.
NOTESPriority when dealing with a number of faults:
- Deal first with fault DF113 Sensor supply voltage.
See Technical Note Wiring Diagrams of the vehicle concerned.
Check the connection and condition of the EGR valve connector, component code 169.
Check the connection and condition of connector B (brown 48-track) of the computer, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for +5 V on connection 3GC of component 169.
Check for earth on connection 3JM of component 169.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check the insulation and continuity of the following connections:
–3GC between components 169 and 120,
–3EL between components 169 and 120,
–3JM between components 169 and 120.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check the resistance of the EGR valve, component code 169:
– with the engine stopped, the EGR valve will be closed (unless there is a fault),
– wait for the ambient temperature around the valve to stabilise (approximately 20°C),
– measure the resistance between connections 3FB2 and 3GB. The resistance must be between
7.54 Ω < R < 8.5 Ω (at 20°C),
– measure the resistance between connections 3GC and
3JM. The resistance must be between
2.4 KΩ < R < 5.6 KΩ (at 20°C),
– measure the resistance between connections 3JM and 3EL, the resistance should be between
800 Ω < R < 3.6 KΩ (at 20°C),
if the value is not correct, replace the EGR valve, component code 1460 (see MR 364 (Mégane II), MR 370
(Scénic II), Mechanical, 14A, Emission control, Exhaust gas recirculation solenoid valve: Removal -
Refitting). If the EGR valve was replaced, use command RZ002 EGR adaptives to reinitialise the EGR valve
offsets.
If the fault is still present, contact the Techline.
DDCR_V44_DF010M/DDCR_V48_DF010M

13B-36
AFTER REPAIRDeal with any faults displayed by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$061.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF016
STOREDEGR VALVE CONTROL CIRCUITCO.0: Open circuit or short circuit to earth.
CC.1: Short circuit to +12 volts.
NOTESConditions for applying fault finding procedures to stored faults:
The fault is present with the engine idling.
Special notes:
If fault DF016 is present: the engine is unstable and may even stall.
Starting difficult or even impossible when cold.
See Technical Note Wiring Diagrams of the vehicle concerned.
Check the connection and condition of the exhaust gas recirculation solenoid valve connector, component code
169.
Check the connection and condition of connector B (brown 48-track) of the injection computer, component code
120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for the supply: 13 V < X < 14 V (with the engine running), 11.5 V < X < 12.5 V (with the ignition on and
the engine stopped) on connection 3FB2 of component 169.
Check the insulation and continuity of the following connections:
–3GB between components 169 and 120,
–3FB2 between components 169 and 120.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Measure the resistance of the EGR valve, component code 169:
– with the engine stopped, the EGR valve will be closed (unless there is a fault),
– wait for the ambient temperature around the valve to stabilise (approximately 20°C),
– measure the resistance between connections 3FB2 and 3GB of component 169. The resistance must be
between
7.5 Ω
< R < 8.5 Ω (at 20°C),
– measure the resistance between connections 3GC and 3JM of component 169. The resistance must be between
2.4 KΩ < R < 5.6 KΩ (at 20°C),
– measure the resistance between connections 3JM and 3EL of component 169. The resistance must be between
800 Ω < R < 3.6 KΩ (ατ 20°C),
if the value is not correct, replace the EGR valve (see MR 364 (Mégane II), MR 370
(Scénic II), Mechanical, 14A, Emission control, Exhaust gas recirculation solenoid valve: Removal -
Refitting). If the EGR valve was replaced, use command RZ002 EGR adaptives to reinitialise the EGR valve
offsets.
If the fault is still present, contact the Techline.
DDCR_V44_DF016M/DDCR_V48_DF016M

13B-75
AFTER REPAIRDeal with any faults declared by the diagnostic tool. Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V4 MR-372-J84-13B000$062.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DDCR INJECTION
Vdiag No.: 44, 48
DF114
STOREDEGR SOLENOID VALVE CIRCUIT
1.DEF: At minimum limit
2.DEF: At maximum limit
3.DEF: Inconsistency
4.DEF: Valve jammed
5.DEF: Valve clogged
NOTESPriority when dealing with a number of faults:
– DF113 Sensor supply voltage.
Special notes:
If fault DF114 is present: the engine is unstable and may even stall. Starting difficult or
even impossible when cold, smoke emissions and loss of performance possible. On
status 4.DEF, the level 1 warning light illuminates with the message Faulty injection
displayed on the instrument panel.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine running.
See Technical Note Wiring Diagrams of the vehicle concerned.
Check the connection and condition of the EGR valve connector, component code 169.
Check the connection and condition of connector B (brown 48-track) of the injection computer, component
code120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for +12 V on connection 3FB2 of component 169.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation and continuity of the following connections:
–3GB between components 169 and 120,
–3FB2 between components 169 and 1337.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
DDCR_V44_DF114M/DDCR_V48_DF114M