ESP RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 Workshop Manual

13B-196
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF310
CONTINUED
If the wiring of the particle filter downstream temperature sensor, component code 1288, is present (with or without
the sensor being present), check the electrical insulation in relation to + 12 V between the following connections:
–3XU between components 120 and 1288,
–3TG between components 120 and 1288.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the particle filter upstream temperature sensor.
CO.1
NOTESNone.
Check the condition of the particle filter upstream temperature sensor connector (see Wiring Diagram Technical
Note, Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 1287).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and insulation from + 12 V of the following connections:
•3XT between components 120 and 1287,
•3TD between components 120 and 1287.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, replace the particle filter upstream temperature sensor.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-198
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
diff.*: Differential
temp.*: Temperature
DF311
CONTINUED
The fault appears following:
–7 failed regenerations when driving for Laguna II ph2.
–Between 9 and 11 failed regenerations when driving for Mégane II ph2, Vel Satis ph2 and Espace IV ph2.
If Vdiag 18, reprogram the computer (see Replacement of components). Then apply the procedure
corresponding to the new Vdiag.
For the other Vdiag:
Check that there are no leaks or blockages in the exhaust pipe,
Repair if necessary.
Explain the regeneration procedure when driving to the customer to avoid unnecessary repairs: see SECTION D
in the interpretation of DF312 Speed request.
If the fault is still present, contact the Techline.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 54, 58, 5C, 60

13B-200
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF312
CONTINUED 1
The fault appears:
–Vdiag 18 and 1C:
4 failed regeneration attempts (for Laguna II ph2) and 5 failed regeneration attempts (for Vel Satis ph2 and
Espace IV ph2) when driving and the weight of soot in the particle filter is above 20 g.
–Vdiag54:
5 failed regeneration attempts (for Mégane ph2) when driving and the weight of soot in the particle filter is above
20 g.
– Vdiag 20, 24 and 26:
4 failed regeneration attempts (for Laguna II ph2) and 5 failed regeneration attempts (for Vel Satis ph2 and
Espace IV ph2) and 7 failed regeneration attempts (for Espace IV ph2, M9R 761 only) when driving and the weight
of soot in the particle filter is above 20 g for M9R760 and M9R762 or 36 g for M9R761 and M9R763.
–Vdiag 5C and 58:
5 failed regeneration attempts (for Mégane II ph2, M9R 722/724 only) and 7 failed regeneration attempts (for
Mégane II ph2, M9R 721 only) when driving and the weight of soot in the particle filter is above 20 g for M9R 722/
724 or 36 g for M9R 721.
PART A
The flow chart on the following page allows analysis of the driving profile and the causes for the warning to come
on:
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 54, 58, 5C, 60

13B-203
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
13B
DF312
CONTINUED 4
PART B
1. No particle filter regeneration.
2.Write on the repair order the parameter and status relating to the last failure:
– Mileage of the last DF312 Speed request.
– Mileage of the last failures.
– Engine statuses of the last failures.
E.g.: PR787 = 2794 miles (4657 km); PR801 = 2760 miles (4600 km); engine status = STOPPED
3. Interpretation of the values written on the repair order by the service advisor for the customer:
Before the last time the particle filter warning light or message came on (appeared at the Mileage of the last
DF312), the customer had not respected the driving recommendations: the failure that occurred at the Mileage of
the last failure is due to the engine being switched off.
4. Explain to the customer the procedure to turn off the warning light, making use of the parameters noted in the
repair order: see PART D.
PART C
If Vdiag 18:
Reprogram the computer in Vdiag 1C.
Then apply the procedure corresponding to Vdiag 1C.
If Vdiag 1C, 54, 58, 20 and 24:
– Check that there are no leaks or blockages in the exhaust pipe,
Repair if necessary.
– Carry out an After-Sales regeneration with approval from the Techline.
– Follow the procedure for command SC017 Particle filter regeneration (see Interpretation of commands).
– Explain to the customer the procedure for regeneration when driving to avoid unnecessary repairs: see PART D.
DIESEL INJECTION
Fault finding – Interpretation of faults
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 54, 58, 5C, 60

13B-205
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF315
PRESENT
OR
STOREDPARTICLE FILTER DIFFERENTIAL PRESSURE SENSOR
CO: Open circuit
CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to + 12 V
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after the engine is started or following a road test.
Special notes:
If the fault is present:
–the level 1 warning light is lit,
– the EOBD (European On Board Diagnostic) warning light will come on after three
consecutive driving cycles (starting + 5 seconds + switching off the ignition and
waiting for 1 minute),
– the particle filter fault finding procedure is inhibited,
– particle filter regeneration is inhibited.
Priorities when dealing with a number of faults:
–DF315 if it is present.
–DF308 Particle filter clogged if DF315 is stored and DF308 is present.
–DF011 Sensor supply voltage no. 1 if it is present or stored.
CC.1
NOTESNone.
Check the condition of the differential pressure sensor connector (see Wiring Diagram Technical Note, Laguna
II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 1290).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
EDC16CP33_V18_DF315 / EDC16CP33_V1C_DF315 / EDC16CP33_V54_DF315 / EDC16CP33_V20_DF315 / EDC16CP33_V58_DF315 /
EDC16CP33_V5C_DF315 / EDC16CP33_V24_DF315 / EDC16CP33_V28_DF315 / EDC16CP33_V62_DF315 / EDC16CP33_V26_DF315 /
EDC16CP33_V60_DF315
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-206
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF315
CONTINUED
Check the continuity and insulation from + 12 V of the following connections:
•3TL between components 120 and 1290,
•3TM between components 120 and 1290.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, replace the differential pressure sensor.
CO.0
CO
NOTESNone.
Check the condition of the differential pressure sensor connector (see Wiring Diagram Technical Note, Laguna
II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 1290).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and insulation to earth of the following connections:
•3TL between components 120 and 1290,
•3TM between components 120 and 1290.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the wiring of the particle filter downstream temperature sensor, component code 1288, is present (with or without
the sensor being present), check the electrical insulation in relation to + 12 V between the following connections:
–3XU between components 120 and 1288,
–3TG between components 120 and 1288.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the differential pressure sensor.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-207
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF323
PRESENT
OR
STOREDDAMPER VALVECC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CC: Short circuit
C0: Open circuit
1.DEF: Internal electronic fault
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the ignition has been switched on.
Special notes:
If the fault is present:
–the level 1 warning light is lit (for Vdiag 20, 58, 24, 5C, 26, 28, 60 and 62),
– particle filter regeneration is inhibited.
Use bornier Elé. 1681 for all operations on the engine management computer
connector.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
CC.0
CC.1
NOTESNone.
Check the condition of the damper valve connector (see Wiring Diagram Technical Note, Laguna II ph2, Vel
Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 1461).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance between connections 3AAX and 3AAY of component 1461.
If the resistance of the damper valve is less than 0.5 Ω or greater than 400 Ω, replace the damper valve.
Then run command SC036: Reinitialise programming and select Damper valve to reinitialise the valve's
opening and closing stops.
EDC16CP33_V18_DF323 / EDC16CP33_V1C_DF323 / EDC16CP33_V54_DF323 / EDC16CP33_V20_DF323 / EDC16CP33_V58_DF323 /
EDC16CP33_V5C_DF323 / EDC16CP33_V24_DF323 / EDC16CP33_V04_DF323 / EDC16CP33_V08_DF323 / EDC16CP33_V44_DF323 /
EDC16CP33_V4C_DF323 / EDC16CP33_V34_DF323 / EDC16CP33_V38_DF323 / EDC16CP33_V74_DF323 / EDC16CP33_V28_DF323 /
EDC16CP33_V62_DF323 / EDC16CP33_V26_DF323 / EDC16CP33_V60_DF323
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-208
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF323
CONTINUED 1
Check the insulation to earth of the following connections:
•3AAX between components 120 and 1461,
•3AAY between the components 120 and 1461.
Check the insulation from + 12 V of the following connections:
•3AAX between components 120 and 1461,
•3AAY between the components 120 and 1461.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.
CC
NOTESNone.
Check the condition of the damper valve connector (see Wiring Diagram Technical Note, Laguna II ph2, Vel
Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 1461).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance between connections 3AAX and 3AAY of component 1461.
If the resistance of the damper valve is less than 0.5 Ω or greater than 400 Ω, replace the damper valve.
Then run command SC036 Reinitialise programming and select Damper valve to reinitialise the valve's opening
and closing stops.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-209
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF323
CONTINUED 2
Check the insulation between the following connections:
•3AAX between components 120 and 1461,
•3AAY between the components 120 and 1461.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.
CO
NOTESNone.
Check the condition of the damper valve connector (see Wiring Diagram Technical Note, Laguna II ph2, Vel
Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 1461).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance between connections 3AAX and 3AAY of component 1461.
If the resistance of the damper valve is less than 0.5 Ω or greater than 400 Ω, replace the damper valve.
Then run command SC036: Reinitialise programming and select Damper valve to reinitialise the valve's
opening and closing stops.
Check the continuity of the following connections:
•3AAX between components 120 and 1461,
•3AAY between the components 120 and 1461.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-210
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$074.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF323
CONTINUED 3
1.DEFNOTESSpecial notes:
This fault appears when the computer control section has
overheated. A road test may be necessary.
Priorities when dealing with a number of faults:
Deal with CO, CO.0, CC.1 and CO first if they are present or
stored.
Check the condition of the damper valve connector (see Wiring Diagram Technical Note, Laguna II ph2, Vel
Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 1461).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity of the following connections:
•3AAX between components 120 and 1461,
•3AAY between the components 120 and 1461.
Check the insulation from + 5 V (computer supplies) of the following connections:
•3AAX between components 120 and 1461,
•3AAY between the components 120 and 1461.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74