check engine RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2012, Model line: SCENIC, Model: RENAULT SCENIC 2012 J95 / 3.GPages: 510, PDF Size: 2.98 MB
Page 353 of 510
13B-353
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR059INLET AIR TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the air inlet temperature in °C.
NOTESThere must be no present or stored faults.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (e.g. lack of power).
Use the Technical Note Wiring Diagram, Laguna II ph2, Vel Satis ph2, Mégane ll
ph2, Scénic ll ph2, Espace IV ph2.
Conformity check: Engine stopped and ignition on
With the ignition on the inlet air temperature varies according to the exterior temperature.
In the event of a fault, consult the interpretation of fault DF002 Air temperature sensor circuit.
Parameter PR059 ≈ PR064 Coolant temperature engine cold.
Conformity check with the engine running and engine coolant temperature > 80°C
With the engine running at idle speed the inlet air temperature varies according to the engine coolant temperature.
In the event of a fault, refer to the interpretation of fault DF002.
EDC16CP33_V18_PR059 / EDC16CP33_V1C_PR059 / EDC16CP33_V54_PR059 / EDC16CP33_V20_PR059 / EDC16CP33_V58_PR059 /
EDC16CP33_V5C_PR059 / EDC16CP33_V24_PR059 / EDC16CP33_V04_PR059 / EDC16CP33_V08_PR059 / EDC16CP33_V44_PR059 /
EDC16CP33_V4C_PR059 / EDC16CP33_V34_PR059 / EDC16CP33_V38_PR059 / EDC16CP33_V74_PR059 / EDC16CP33_V28_PR059 /
EDC16CP33_V62_PR059 / EDC16CP33_V26_PR059 / EDC16CP33_V60_PR059
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
Page 355 of 510
13B-355
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR061EXTERIOR AIR TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the exterior air temperature in °C.
NOTESNone.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The exterior air temperature value must be:
PR061 = 20°C (default value).
This parameter is controlled by the UCH and transmitted to the injection on the multiplex network.
In the event of a fault, run fault finding on the UCH (see 87B, Passenger compartment connection unit).
EDC16CP33_V18_PR061 / EDC16CP33_V1C_PR061 / EDC16CP33_V54_PR061 / EDC16CP33_V20_PR061 / EDC16CP33_V58_PR061 /
EDC16CP33_V5C_PR061 / EDC16CP33_V24_PR061 / EDC16CP33_V04_PR061 / EDC16CP33_V08_PR061 / EDC16CP33_V44_PR061 /
EDC16CP33_V4C_PR061 / EDC16CP33_V34_PR061 / EDC16CP33_V38_PR061 / EDC16CP33_V74_PR061 / EDC16CP33_V28_PR061 /
EDC16CP33_V62_PR061 / EDC16CP33_V26_PR061 / EDC16CP33_V60_PR061
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
Page 356 of 510
13B-356
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR063FUEL TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the fuel temperature in °C.
NOTESThere must be no present or stored faults.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (e.g. lack of power).
Use the Technical Note Wiring Diagram, Laguna II ph2, Vel Satis ph2, Mégane ll
ph2, Scénic ll ph2, Espace IV ph2.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The fuel temperature value must be between:
– 30°C < PR063 <90°C
PR063 = 100°C (default value).
In the event of a fault, consult the interpretation of fault DF098 Fuel temperature sensor circuit.
EDC16CP33_V18_PR063 / EDC16CP33_V1C_PR063 / EDC16CP33_V54_PR063 / EDC16CP33_V20_PR063 / EDC16CP33_V58_PR063 /
EDC16CP33_V5C_PR063 / EDC16CP33_V24_PR063 / EDC16CP33_V04_PR063 / EDC16CP33_V08_PR063 / EDC16CP33_V44_PR063 /
EDC16CP33_V4C_PR063 / EDC16CP33_V34_PR063 / EDC16CP33_V38_PR063 / EDC16CP33_V74_PR063 / EDC16CP33_V28_PR063 /
EDC16CP33_V62_PR063 / EDC16CP33_V26_PR063 / EDC16CP33_V60_PR063
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
Page 358 of 510
13B-358
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR064COOLANT TEMPERATURE
PARAMETER
DEFINITIONThis parameter indicates the engine coolant temperature in °C.
NOTESThere must be no present or stored faults.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (e.g. lack of power).
Use the Technical Note Wiring Diagram, Laguna II ph2, Vel Satis ph2, Mégane ll
ph2, Scénic ll ph2, Espace IV ph2.
Conformity check with engine stopped and ignition on.
With the ignition on the coolant temperature varies according to the exterior temperature.
In the event of a fault, consult the interpretation of fault DF001 Coolant temperature sensor circuit.
Parameter PR059: Inlet air temperature ≈ PR064 engine cold.
Conformity check with the engine running and engine coolant temperature > 80°C
With the engine running at idle speed the coolant temperature varies according to the engine temperature.
If there is a fault, refer to the interpretation of fault DF001.
EDC16CP33_V18_PR064 / EDC16CP33_V1C_PR064 / EDC16CP33_V54_PR064 / EDC16CP33_V20_PR064 / EDC16CP33_V58_PR064 /
EDC16CP33_V5C_PR064 / EDC16CP33_V24_PR064 / EDC16CP33_V04_PR064 / EDC16CP33_V08_PR064 / EDC16CP33_V44_PR064 /
EDC16CP33_V4C_PR064 / EDC16CP33_V34_PR064 / EDC16CP33_V38_PR064 / EDC16CP33_V74_PR064 / EDC16CP33_V28_PR064 /
EDC16CP33_V62_PR064 / EDC16CP33_V26_PR064 / EDC16CP33_V60_PR064
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
Page 360 of 510
13B-360
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR074BATTERY VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the battery voltage in volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The battery voltage value must be between:
8.5 V < PR074 < 15 V.
Test the battery and run fault finding on the charging circuit (see Technical Note 6014A, Charging circuit check).
EDC16CP33_V18_PR074 / EDC16CP33_V1C_PR074 / EDC16CP33_V54_PR074 / EDC16CP33_V20_PR074 / EDC16CP33_V58_PR074 /
EDC16CP33_V5C_PR074 / EDC16CP33_V24_PR074 / EDC16CP33_V04_PR074 / EDC16CP33_V08_PR074 / EDC16CP33_V44_PR074 /
EDC16CP33_V4C_PR074 / EDC16CP33_V34_PR074 / EDC16CP33_V38_PR074 / EDC16CP33_V74_PR074 / EDC16CP33_V28_PR074 /
EDC16CP33_V62_PR074 / EDC16CP33_V26_PR074 / EDC16CP33_V60_PR074
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
Page 361 of 510
13B-361
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR077EGR VALVE POSITION SENSOR VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the EGR valve position sensor voltage in volts.
NOTESNone.
Conformity check: Engine stopped and ignition on
The EGR valve position sensor voltage value must be between:
0 < PR077 < 1.5 V
The default value is: X = 0 V
In the event of a fault, refer to the interpretation of fault DF012 Sensor supply voltage no. 2.
Engine running, engine coolant temperature > 80°C, with no electrical consumers
The EGR valve position sensor voltage value must be between:
0 V < PR077 < 5 V
The default value is: X = 0 V
In the event of a fault, refer to the interpretation of fault DF012.
EDC16CP33_V18_PR077 / EDC16CP33_V1C_PR077 / EDC16CP33_V54_PR077 / EDC16CP33_V20_PR077 / EDC16CP33_V58_PR077 /
EDC16CP33_V5C_PR077 / EDC16CP33_V24_PR077 / EDC16CP33_V04_PR077 / EDC16CP33_V08_PR077 / EDC16CP33_V44_PR077 /
EDC16CP33_V4C_PR077 / EDC16CP33_V34_PR077 / EDC16CP33_V38_PR077 / EDC16CP33_V74_PR077 / EDC16CP33_V28_PR077 /
EDC16CP33_V62_PR077 / EDC16CP33_V26_PR077 / EDC16CP33_V60_PR077
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
Page 362 of 510
13B-362
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR079ATMOSPHERIC PRESSURE SENSOR VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the atmospheric pressure sensor voltage in volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The value of the atmospheric pressure sensor voltage must be between:
0 V < PR079 < 5 V.
In the event of a fault, consult the interpretation of faults DF011 Sensor supply no. 1 voltage, DF012 Sensor
supply no. 2 voltage, and DF013 Sensor supply no. 3 voltage.
EDC16CP33_V18_PR079 / EDC16CP33_V1C_PR079 / EDC16CP33_V54_PR079 / EDC16CP33_V20_PR079 / EDC16CP33_V58_PR079 /
EDC16CP33_V5C_PR079 / EDC16CP33_V24_PR079 / EDC16CP33_V04_PR079 / EDC16CP33_V08_PR079 / EDC16CP33_V44_PR079 /
EDC16CP33_V4C_PR079 / EDC16CP33_V34_PR079 / EDC16CP33_V38_PR079 / EDC16CP33_V74_PR079 / EDC16CP33_V28_PR079 /
EDC16CP33_V62_PR079 / EDC16CP33_V26_PR079 / EDC16CP33_V60_PR079
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
Page 363 of 510
13B-363
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR080RAIL PRESSURE SENSOR VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the rail pressure sensor voltage in volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The value of the rail position sensor voltage must be between:
0 V
EDC16CP33_V18_PR080 / EDC16CP33_V1C_PR080 / EDC16CP33_V54_PR080 / EDC16CP33_V20_PR080 / EDC16CP33_V58_PR080 /
EDC16CP33_V5C_PR080 / EDC16CP33_V24_PR080 / EDC16CP33_V04_PR080 / EDC16CP33_V08_PR080 / EDC16CP33_V44_PR080 /
EDC16CP33_V4C_PR080 / EDC16CP33_V34_PR080 / EDC16CP33_V38_PR080 / EDC16CP33_V74_PR080 / EDC16CP33_V28_PR080 /
EDC16CP33_V62_PR080 / EDC16CP33_V26_PR080 / EDC16CP33_V60_PR080
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
Page 364 of 510
13B-364
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR082FUEL TEMPERATURE SENSOR VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the fuel temperature sensor voltage in volts.
NOTESNone.
Conformity check: Engine stopped and ignition on, or Engine running and engine coolant
temperature > 80°C without electrical consumers
0 V < PR082 < 5 V
In the event of a fault, consult the interpretation of fault DF098 Fuel temperature sensor circuit.
EDC16CP33_V18_PR082 / EDC16CP33_V1C_PR082 / EDC16CP33_V54_PR082 / EDC16CP33_V20_PR082 / EDC16CP33_V58_PR082 /
EDC16CP33_V5C_PR082 / EDC16CP33_V24_PR082 / EDC16CP33_V04_PR082 / EDC16CP33_V08_PR082 / EDC16CP33_V44_PR082 /
EDC16CP33_V4C_PR082 / EDC16CP33_V34_PR082 / EDC16CP33_V38_PR082 / EDC16CP33_V74_PR082 / EDC16CP33_V28_PR082 /
EDC16CP33_V62_PR082 / EDC16CP33_V26_PR082 / EDC16CP33_V60_PR082
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
Page 365 of 510
13B-365
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR083AIR TEMPERATURE SENSOR VOLTAGE
PARAMETER
DEFINITIONThis parameter indicates the air temperature sensor voltage in volts.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The value of the air temperature sensor voltage must be between:
0 V < PR083 < 5 V.
In the event of a fault, consult the interpretation of faults DF011 Sensor supply voltage no. 1, DF012 Sensor
supply voltage no. 2 and DF013 Sensor supply voltage no. 3.
EDC16CP33_V18_PR083 / EDC16CP33_V1C_PR083 / EDC16CP33_V54_PR083 / EDC16CP33_V20_PR083 / EDC16CP33_V58_PR083 /
EDC16CP33_V5C_PR083 / EDC16CP33_V24_PR083 / EDC16CP33_V04_PR083 / EDC16CP33_V08_PR083 / EDC16CP33_V44_PR083 /
EDC16CP33_V4C_PR083 / EDC16CP33_V34_PR083 / EDC16CP33_V38_PR083 / EDC16CP33_V74_PR083 / EDC16CP33_V28_PR083 /
EDC16CP33_V62_PR083 / EDC16CP33_V26_PR083 / EDC16CP33_V60_PR083
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74