manual transmission RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 Workshop Manual

13B-294V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET285INJECTION -> AUTOMATIC TRANSMISSION CONNECTION
STATUS
DEFINITIONPRESENT
ABSENT
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
PRESENTThere is a multiplex connection between the injection computer and the automatic
transmission computer.
ABSENTThere is no multiplex connection between the injection computer and the automatic
transmission computer, as there is a manual gearbox.
If there is an automatic transmission and the message ABSENT appears:
Run a multiplex network test (see 88B, Multiplex).
Check the continuity and insulation to earth of the following connections:
•3MS and 3MT between components 119 and 120.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
EDC16CP33_V18_ET285 / EDC16CP33_V1C_ET285 / EDC16CP33_V54_ET285 / EDC16CP33_V20_ET285 / EDC16CP33_V58_ET285 /
EDC16CP33_V5C_ET285 / EDC16CP33_V24_ET285 / EDC16CP33_V28_ET285 / EDC16CP33_V62_ET285 / EDC16CP33_V26_ET285 /
EDC16CP33_V60_ET285
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 28, 54, 58, 5C, 60, 62

13B-300V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 2
STATUS 2
Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes STATUS 2, when driving with the cruise control active
(ET042: CRUISE CONTROL) and brake pedal depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 2 without depressing the brake pedal, consult
the interpretation of statuses ET704 Brake contact no. 1 and ET705 Brake
contact no. 2.
STATUS 3Clutch pedal depressed
Manual gearbox ONLY
The cruise control function is deactivated when the gearbox is not coupled to
the engine (clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with the cruise control active
(ET042 Cruise control / speed limiter: CRUISE CONTROL) and the clutch pedal is
depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 becomes STATUS 3 without the clutch pedal being depressed, consult
the interpretation of status ET405 Clutch pedal switch.
If the vehicle is fitted with an automatic transmission:
Test the multiplex network: check the configuration of the multiplex network in relation
to the vehicle's technical specification, especially the configuration of the automatic
transmission computer (see 88B, Multiplexing).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-302V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 4
STATUS 5
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 changes to STATUS 5, deal with present faults or those stored in
the injection computer.
If the fault is still present, contact the Techline.
STATUS 6Gear lever in neutral (manual gearbox) or neutral (automatic gearbox)
Status ET415 changes to STATUS 6, when driving, with cruise control active (ET042:
CRUISE CONTROL) and:
– if the driver puts the gear lever in neutral position on a manual gearbox without
declutching or,
– if the gear lever is put in neutral on an automatic transmission.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 Fault memory.
If status ET415 becomes STATUS 6 without shifting the gear lever into neutral on
a manual gearbox without declutching, or into the neutral position on an automatic
transmission, run fault finding on the ABS computer and check the configuration of the
tyre size stored in the computer. If the configuration is correct, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74